blob: 02c059897784d18fba755a61ec8e79b2438e544b [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Mainly by David Woodhouse, somewhat modified by Jordan Crouse
*
* Copyright © 2006-2007 Red Hat, Inc.
* Copyright © 2006-2007 Advanced Micro Devices, Inc.
* Copyright © 2009 VIA Technology, Inc.
* Copyright (c) 2010 Andres Salomon <dilinger@queued.net>
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/cs5535.h>
#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <asm/olpc.h>
#include "olpc_dcon.h"
enum dcon_gpios {
OLPC_DCON_STAT0,
OLPC_DCON_STAT1,
OLPC_DCON_IRQ,
OLPC_DCON_LOAD,
OLPC_DCON_BLANK,
};
static const struct dcon_gpio gpios_asis[] = {
[OLPC_DCON_STAT0] = { .name = "dcon_stat0", .flags = GPIOD_ASIS },
[OLPC_DCON_STAT1] = { .name = "dcon_stat1", .flags = GPIOD_ASIS },
[OLPC_DCON_IRQ] = { .name = "dcon_irq", .flags = GPIOD_ASIS },
[OLPC_DCON_LOAD] = { .name = "dcon_load", .flags = GPIOD_ASIS },
[OLPC_DCON_BLANK] = { .name = "dcon_blank", .flags = GPIOD_ASIS },
};
static struct gpio_desc *gpios[5];
static int dcon_init_xo_1(struct dcon_priv *dcon)
{
unsigned char lob;
int ret, i;
const struct dcon_gpio *pin = &gpios_asis[0];
for (i = 0; i < ARRAY_SIZE(gpios_asis); i++) {
gpios[i] = devm_gpiod_get(&dcon->client->dev, pin[i].name,
pin[i].flags);
if (IS_ERR(gpios[i])) {
ret = PTR_ERR(gpios[i]);
pr_err("failed to request %s GPIO: %d\n", pin[i].name,
ret);
return ret;
}
}
/* Turn off the event enable for GPIO7 just to be safe */
cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);
/*
* Determine the current state by reading the GPIO bit; earlier
* stages of the boot process have established the state.
*
* Note that we read GPIO_OUTPUT_VAL rather than GPIO_READ_BACK here;
* this is because OFW will disable input for the pin and set a value..
* READ_BACK will only contain a valid value if input is enabled and
* then a value is set. So, future readings of the pin can use
* READ_BACK, but the first one cannot. Awesome, huh?
*/
dcon->curr_src = cs5535_gpio_isset(OLPC_GPIO_DCON_LOAD, GPIO_OUTPUT_VAL)
? DCON_SOURCE_CPU
: DCON_SOURCE_DCON;
dcon->pending_src = dcon->curr_src;
/* Set the directions for the GPIO pins */
gpiod_direction_input(gpios[OLPC_DCON_STAT0]);
gpiod_direction_input(gpios[OLPC_DCON_STAT1]);
gpiod_direction_input(gpios[OLPC_DCON_IRQ]);
gpiod_direction_input(gpios[OLPC_DCON_BLANK]);
gpiod_direction_output(gpios[OLPC_DCON_LOAD],
dcon->curr_src == DCON_SOURCE_CPU);
/* Set up the interrupt mappings */
/* Set the IRQ to pair 2 */
cs5535_gpio_setup_event(OLPC_GPIO_DCON_IRQ, 2, 0);
/* Enable group 2 to trigger the DCON interrupt */
cs5535_gpio_set_irq(2, DCON_IRQ);
/* Select edge level for interrupt (in PIC) */
lob = inb(0x4d0);
lob &= ~(1 << DCON_IRQ);
outb(lob, 0x4d0);
/* Register the interrupt handler */
if (request_irq(DCON_IRQ, &dcon_interrupt, 0, "DCON", dcon)) {
pr_err("failed to request DCON's irq\n");
return -EIO;
}
/* Clear INV_EN for GPIO7 (DCONIRQ) */
cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_INVERT);
/* Enable filter for GPIO12 (DCONBLANK) */
cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_FILTER);
/* Disable filter for GPIO7 */
cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_FILTER);
/* Disable event counter for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
cs5535_gpio_clear(OLPC_GPIO_DCON_IRQ, GPIO_INPUT_EVENT_COUNT);
cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_INPUT_EVENT_COUNT);
/* Add GPIO12 to the Filter Event Pair #7 */
cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_FE7_SEL);
/* Turn off negative Edge Enable for GPIO12 */
cs5535_gpio_clear(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_EN);
/* Enable negative Edge Enable for GPIO7 */
cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_EN);
/* Zero the filter amount for Filter Event Pair #7 */
cs5535_gpio_set(0, GPIO_FLTR7_AMOUNT);
/* Clear the negative edge status for GPIO7 and GPIO12 */
cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);
cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_NEGATIVE_EDGE_STS);
/* FIXME: Clear the positive status as well, just to be sure */
cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_POSITIVE_EDGE_STS);
cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_POSITIVE_EDGE_STS);
/* Enable events for GPIO7 (DCONIRQ) and GPIO12 (DCONBLANK) */
cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_EVENTS_ENABLE);
cs5535_gpio_set(OLPC_GPIO_DCON_BLANK, GPIO_EVENTS_ENABLE);
return 0;
}
static void dcon_wiggle_xo_1(void)
{
int x;
/*
* According to HiMax, when powering the DCON up we should hold
* SMB_DATA high for 8 SMB_CLK cycles. This will force the DCON
* state machine to reset to a (sane) initial state. Mitch Bradley
* did some testing and discovered that holding for 16 SMB_CLK cycles
* worked a lot more reliably, so that's what we do here.
*
* According to the cs5536 spec, to set GPIO14 to SMB_CLK we must
* simultaneously set AUX1 IN/OUT to GPIO14; ditto for SMB_DATA and
* GPIO15.
*/
cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_VAL);
cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_ENABLE);
cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_ENABLE);
cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX2);
cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX2);
cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
cs5535_gpio_clear(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);
for (x = 0; x < 16; x++) {
udelay(5);
cs5535_gpio_clear(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
udelay(5);
cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_VAL);
}
udelay(5);
cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_OUTPUT_AUX1);
cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_OUTPUT_AUX1);
cs5535_gpio_set(OLPC_GPIO_SMB_CLK, GPIO_INPUT_AUX1);
cs5535_gpio_set(OLPC_GPIO_SMB_DATA, GPIO_INPUT_AUX1);
}
static void dcon_set_dconload_1(int val)
{
gpiod_set_value(gpios[OLPC_DCON_LOAD], val);
}
static int dcon_read_status_xo_1(u8 *status)
{
*status = gpiod_get_value(gpios[OLPC_DCON_STAT0]);
*status |= gpiod_get_value(gpios[OLPC_DCON_STAT1]) << 1;
/* Clear the negative edge status for GPIO7 */
cs5535_gpio_set(OLPC_GPIO_DCON_IRQ, GPIO_NEGATIVE_EDGE_STS);
return 0;
}
struct dcon_platform_data dcon_pdata_xo_1 = {
.init = dcon_init_xo_1,
.bus_stabilize_wiggle = dcon_wiggle_xo_1,
.set_dconload = dcon_set_dconload_1,
.read_status = dcon_read_status_xo_1,
};