blob: 0e4613bb56eeae02d496be3784517760cf425537 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
* Device Tree file for Marvell Armada 385 Access Point Development board
* (DB-88F6820-AP)
*
* Copyright (C) 2014 Marvell
*
* Nadav Haklai <nadavh@marvell.com>
*/
/dts-v1/;
#include "armada-385.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Marvell Armada 385 Access Point Development Board";
compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada380";
chosen {
stdout-path = "serial1:115200n8";
};
memory {
device_type = "memory";
reg = <0x00000000 0x80000000>; /* 2GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
i2c0: i2c@11000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
/*
* This bus is wired to two EEPROM
* sockets, one of which holding the
* board ID used by the bootloader.
* Erasing this EEPROM's content will
* brick the board.
* Use this bus with caution.
*/
};
mdio@72004 {
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
phy0: ethernet-phy@1 {
reg = <1>;
};
phy1: ethernet-phy@4 {
reg = <4>;
};
phy2: ethernet-phy@6 {
reg = <6>;
};
};
/* UART0 is exposed through the JP8 connector */
uart0: serial@12000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
/*
* UART1 is exposed through a FTDI chip
* wired to the mini-USB connector
*/
uart1: serial@12100 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
pinctrl@18000 {
xhci0_vbus_pins: xhci0-vbus-pins {
marvell,pins = "mpp44";
marvell,function = "gpio";
};
};
/* CON3 */
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
buffer-manager = <&bm>;
bm,pool-long = <1>;
bm,pool-short = <3>;
};
/* CON2 */
ethernet@34000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
buffer-manager = <&bm>;
bm,pool-long = <2>;
bm,pool-short = <3>;
};
usb@58000 {
status = "okay";
};
/* CON4 */
ethernet@70000 {
pinctrl-names = "default";
/*
* The Reference Clock 0 is used to
* provide a clock to the PHY
*/
pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
buffer-manager = <&bm>;
bm,pool-long = <0>;
bm,pool-short = <3>;
};
bm@c8000 {
status = "okay";
};
usb3@f0000 {
status = "okay";
usb-phy = <&usb3_phy>;
};
};
bm-bppi {
status = "okay";
};
pcie {
status = "okay";
/*
* The three PCIe units are accessible through
* standard mini-PCIe slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
pcie@3,0 {
/* Port 2, Lane 0 */
status = "okay";
};
};
};
usb3_phy: usb3_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_xhci0_vbus>;
#phy-cells = <0>;
};
reg_xhci0_vbus: xhci0-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&xhci0_vbus_pins>;
regulator-name = "xhci0-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
};
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
status = "okay";
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p128", "jedec,spi-nor";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <54000000>;
};
};
&nand_controller {
status = "okay";
nand@0 {
reg = <0>;
label = "pxa3xx_nand-0";
nand-rb = <0>;
nand-on-flash-bbt;
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "U-Boot";
reg = <0x00000000 0x00800000>;
read-only;
};
partition@800000 {
label = "uImage";
reg = <0x00800000 0x00400000>;
read-only;
};
partition@c00000 {
label = "Root";
reg = <0x00c00000 0x3f400000>;
};
};
};
};