blob: 7b151894f5a0df4158e1f5186bb9a2c469448fed [file] [log] [blame]
Qualcomm Technologies, Inc. IPQ8074 TLMM block
This binding describes the Top Level Mode Multiplexer block found in the
IPQ8074 platform.
- compatible:
Usage: required
Value type: <string>
Definition: must be "qcom,ipq8074-pinctrl"
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: the base address and size of the TLMM register space.
- interrupts:
Usage: required
Value type: <prop-encoded-array>
Definition: should specify the TLMM summary IRQ.
- interrupt-controller:
Usage: required
Value type: <none>
Definition: identifies this node as an interrupt controller
- #interrupt-cells:
Usage: required
Value type: <u32>
Definition: must be 2. Specifying the pin number and flags, as defined
in <dt-bindings/interrupt-controller/irq.h>
- gpio-controller:
Usage: required
Value type: <none>
Definition: identifies this node as a gpio controller
- #gpio-cells:
Usage: required
Value type: <u32>
Definition: must be 2. Specifying the pin number and flags, as defined
in <dt-bindings/gpio/gpio.h>
- gpio-ranges:
Usage: required
Definition: see ../gpio/gpio.txt
- gpio-reserved-ranges:
Usage: optional
Definition: see ../gpio/gpio.txt
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
The pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those pin(s)/group(s), and various pin configuration
parameters, such as pull-up, drive strength, etc.
PIN CONFIGURATION NODES:
The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.
Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.
The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:
- pins:
Usage: required
Value type: <string-array>
Definition: List of gpio pins affected by the properties specified in
this subnode. Valid pins are:
gpio0-gpio69
- function:
Usage: required
Value type: <string>
Definition: Specify the alternative function to be configured for the
specified pins. Functions are only valid for gpio pins.
Valid values are:
atest_char, atest_char0, atest_char1, atest_char2,
atest_char3, audio_rxbclk, audio_rxd, audio_rxfsync,
audio_rxmclk, audio_txbclk, audio_txd, audio_txfsync,
audio_txmclk, blsp0_i2c, blsp0_spi, blsp0_uart, blsp1_i2c,
blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, blsp2_uart,
blsp3_i2c, blsp3_spi, blsp3_spi0, blsp3_spi1, blsp3_spi2,
blsp3_spi3, blsp3_uart, blsp4_i2c0, blsp4_i2c1, blsp4_spi0,
blsp4_spi1, blsp4_uart0, blsp4_uart1, blsp5_i2c, blsp5_spi,
blsp5_uart, burn0, burn1, cri_trng, cri_trng0, cri_trng1,
cxc0, cxc1, dbg_out, gcc_plltest, gcc_tlmm, gpio, ldo_en,
ldo_update, led0, led1, led2, mac0_sa0, mac0_sa1, mac1_sa0,
mac1_sa1, mac1_sa2, mac1_sa3, mac2_sa0, mac2_sa1, mdc,
mdio, pcie0_clk, pcie0_rst, pcie0_wake, pcie1_clk,
pcie1_rst, pcie1_wake, pcm_drx, pcm_dtx, pcm_fsync,
pcm_pclk, pcm_zsi0, pcm_zsi1, prng_rosc, pta1_0, pta1_1,
pta1_2, pta2_0, pta2_1, pta2_2, pwm0, pwm1, pwm2, pwm3,
qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
qdss_cti_trig_out_a0, qdss_cti_trig_out_a1,
qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b,
qpic, rx0, rx1, rx2, sd_card, sd_write, tsens_max, wci2a,
wci2b, wci2c, wci2d
- bias-disable:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as no pull.
- bias-pull-down:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as pull down.
- bias-pull-up:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as pull up.
- output-high:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
high.
- output-low:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
low.
- drive-strength:
Usage: optional
Value type: <u32>
Definition: Selects the drive strength for the specified pins, in mA.
Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
Example:
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq8074-pinctrl";
reg = <0x1000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&tlmm 0 0 70>;
interrupt-controller;
#interrupt-cells = <2>;
uart2: uart2-default {
mux {
pins = "gpio23", "gpio24";
function = "blsp4_uart1";
};
rx {
pins = "gpio23";
drive-strength = <4>;
bias-disable;
};
tx {
pins = "gpio24";
drive-strength = <2>;
bias-pull-up;
};
};
};