| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_en |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Dither enable. Write 1 to enable dither or 0 to disable it. This is useful |
| for changing the dither parameters. They way it should be done is: |
| |
| - disable dither operation; |
| - change dither parameters (eg: frequency, phase...); |
| - enabled dither operation |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_raw |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This raw, unscaled value refers to the dither signal amplitude. |
| The same scale as in out_voltageY_raw applies. However, the |
| offset might be different as it's always 0 for this attribute. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_raw_available |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Available range for dither raw amplitude values. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_offset |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Offset applied to out_voltageY_dither_raw. Read only attribute |
| always set to 0. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_frequency |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Sets the dither signal frequency. Units are in Hz. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_frequency_available |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Returns the available values for the dither frequency. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_phase |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Sets the dither signal phase. Units are in Radians. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_dither_phase_available |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Returns the available values for the dither phase. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_toggle_en |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Toggle enable. Write 1 to enable toggle or 0 to disable it. This is |
| useful when one wants to change the DAC output codes. The way it should |
| be done is: |
| |
| - disable toggle operation; |
| - change out_voltageY_raw0 and out_voltageY_raw1; |
| - enable toggle operation. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw0 |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw1 |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| It has the same meaning as out_voltageY_raw. This attribute is |
| specific to toggle enabled channels and refers to the DAC output |
| code in INPUT_A (_raw0) and INPUT_B (_raw1). The same scale and offset |
| as in out_voltageY_raw applies. |
| |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_symbol |
| KernelVersion: 5.18 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Performs a SW toggle. This attribute is specific to toggle |
| enabled channels and allows to toggle between out_voltageY_raw0 |
| and out_voltageY_raw1 through software. Writing 0 will select |
| out_voltageY_raw0 while 1 selects out_voltageY_raw1. |
