blob: 585caecda3a5fc3a533360eea7ac95589b9c2545 [file] [log] [blame]
What: /sys/class/watchdog/watchdogn/bootstatus
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It contains status of the watchdog
device at boot. It is equivalent to WDIOC_GETBOOTSTATUS of
ioctl interface.
What: /sys/class/watchdog/watchdogn/identity
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It contains identity string of
watchdog device.
What: /sys/class/watchdog/watchdogn/nowayout
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read/write file. While reading, it gives '1'
if the device has the nowayout feature set, otherwise
it gives '0'. Writing a '1' to the file enables the
nowayout feature. Once set, the nowayout feature
cannot be disabled, so writing a '0' either has no
effect (if the feature was already disabled) or
results in a permission error.
What: /sys/class/watchdog/watchdogn/state
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It gives active/inactive status of
watchdog device.
What: /sys/class/watchdog/watchdogn/status
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It contains watchdog device's
internal status bits. It is equivalent to WDIOC_GETSTATUS
of ioctl interface.
What: /sys/class/watchdog/watchdogn/timeleft
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It contains value of time left for
reset generation. It is equivalent to WDIOC_GETTIMELEFT of
ioctl interface.
What: /sys/class/watchdog/watchdogn/timeout
Date: August 2015
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It is read to know about current
value of timeout programmed.
What: /sys/class/watchdog/watchdogn/pretimeout
Date: December 2016
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It specifies the time in seconds before
timeout when the pretimeout interrupt is delivered. Pretimeout
is an optional feature.
What: /sys/class/watchdog/watchdogn/pretimeout_avaialable_governors
Date: February 2017
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read only file. It shows the pretimeout governors
available for this watchdog.
What: /sys/class/watchdog/watchdogn/pretimeout_governor
Date: February 2017
Contact: Wim Van Sebroeck <wim@iguana.be>
Description:
It is a read/write file. When read, the currently assigned
pretimeout governor is returned. When written, it sets
the pretimeout governor.
What: /sys/class/watchdog/watchdog1/access_cs0
Date: August 2019
Contact: Ivan Mikhaylov <i.mikhaylov@yadro.com>,
Alexander Amelkin <a.amelkin@yadro.com>
Description:
It is a read/write file. This attribute exists only if the
system has booted from the alternate flash chip due to
expiration of a watchdog timer of AST2400/AST2500 when
alternate boot function was enabled with 'aspeed,alt-boot'
devicetree option for that watchdog or with an appropriate
h/w strapping (for WDT2 only).
At alternate flash the 'access_cs0' sysfs node provides:
ast2400:
a way to get access to the primary SPI flash
chip at CS0 after booting from the alternate
chip at CS1.
ast2500:
a way to restore the normal address mapping
from (CS0->CS1, CS1->CS0) to (CS0->CS0,
CS1->CS1).
Clearing the boot code selection and timeout counter also
resets to the initial state the chip select line mapping. When
the SoC is in normal mapping state (i.e. booted from CS0),
clearing those bits does nothing for both versions of the SoC.
For alternate boot mode (booted from CS1 due to wdt2
expiration) the behavior differs as described above.
This option can be used with wdt2 (watchdog1) only.
When read, the current status of the boot code selection is
shown. When written with any non-zero value, it clears
the boot code selection and the timeout counter, which results
in chipselect reset for AST2400/AST2500.