blob: 2821425ee44596def3801d52280d0904e770cbb9 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
%YAML 1.2
---
$id: http://devicetree.org/schemas/clock/baikal,bt1-ccu-div.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Baikal-T1 Clock Control Unit Dividers
maintainers:
- Serge Semin <fancer.lancer@gmail.com>
description: |
Clocks Control Unit is the core of Baikal-T1 SoC System Controller
responsible for the chip subsystems clocking and resetting. The CCU is
connected with an external fixed rate oscillator, which signal is transformed
into clocks of various frequencies and then propagated to either individual
IP-blocks or to groups of blocks (clock domains). The transformation is done
by means of an embedded into CCU PLLs and gateable/non-gateable dividers. The
later ones are described in this binding. Each clock domain can be also
individually reset by using the domain clocks divider configuration
registers. Baikal-T1 CCU is logically divided into the next components:
1) External oscillator (normally XTAL's 25 MHz crystal oscillator, but
in general can provide any frequency supported by the CCU PLLs).
2) PLLs clocks generators (PLLs).
3) AXI-bus clock dividers (AXI) - described in this binding file.
4) System devices reference clock dividers (SYS) - described in this binding
file.
which are connected with each other as shown on the next figure:
+---------------+
| Baikal-T1 CCU |
| +----+------|- MIPS P5600 cores
| +-|PLLs|------|- DDR controller
| | +----+ |
+----+ | | | | |
|XTAL|--|-+ | | +---+-|
+----+ | | | +-|AXI|-|- AXI-bus
| | | +---+-|
| | | |
| | +----+---+-|- APB-bus
| +-------|SYS|-|- Low-speed Devices
| +---+-|- High-speed Devices
+---------------+
Each sub-block is represented as a separate DT node and has an individual
driver to be bound with.
In order to create signals of wide range frequencies the external oscillator
output is primarily connected to a set of CCU PLLs. Some of PLLs CLKOUT are
then passed over CCU dividers to create signals required for the target clock
domain (like AXI-bus or System Device consumers). The dividers have the
following structure:
+--------------+
CLKIN --|->+----+ 1|\ |
SETCLK--|--|/DIV|->| | |
CLKDIV--|--| | | |-|->CLKLOUT
LOCK----|--+----+ | | |
| |/ |
| | |
EN------|-----------+ |
RST-----|--------------|->RSTOUT
+--------------+
where CLKIN is the reference clock coming either from CCU PLLs or from an
external clock oscillator, SETCLK - a command to update the output clock in
accordance with a set divider, CLKDIV - clocks divider, LOCK - a signal of
the output clock stabilization, EN - enable/disable the divider block,
RST/RSTOUT - reset clocks domain signal. Depending on the consumer IP-core
peculiarities the dividers may lack of some functionality depicted on the
figure above (like EN, CLKDIV/LOCK/SETCLK). In this case the corresponding
clock provider just doesn't expose either switching functions, or the rate
configuration, or both of them.
The clock dividers, which output clock is then consumed by the SoC individual
devices, are united into a single clocks provider called System Devices CCU.
Similarly the dividers with output clocks utilized as AXI-bus reference clocks
are called AXI-bus CCU. Both of them use the common clock bindings with no
custom properties. The list of exported clocks and reset signals can be found
in the files: 'include/dt-bindings/clock/bt1-ccu.h' and
'include/dt-bindings/reset/bt1-ccu.h'. Since System Devices and AXI-bus CCU
are a part of the Baikal-T1 SoC System Controller their DT nodes are supposed
to be a children of later one.
if:
properties:
compatible:
contains:
const: baikal,bt1-ccu-axi
then:
properties:
clocks:
items:
- description: CCU SATA PLL output clock
- description: CCU PCIe PLL output clock
- description: CCU Ethernet PLL output clock
clock-names:
items:
- const: sata_clk
- const: pcie_clk
- const: eth_clk
else:
properties:
clocks:
items:
- description: External reference clock
- description: CCU SATA PLL output clock
- description: CCU PCIe PLL output clock
- description: CCU Ethernet PLL output clock
clock-names:
items:
- const: ref_clk
- const: sata_clk
- const: pcie_clk
- const: eth_clk
properties:
compatible:
enum:
- baikal,bt1-ccu-axi
- baikal,bt1-ccu-sys
reg:
maxItems: 1
"#clock-cells":
const: 1
"#reset-cells":
const: 1
unevaluatedProperties: false
required:
- compatible
- "#clock-cells"
- clocks
- clock-names
examples:
# AXI-bus Clock Control Unit node:
- |
#include <dt-bindings/clock/bt1-ccu.h>
clock-controller@1f04d030 {
compatible = "baikal,bt1-ccu-axi";
reg = <0x1f04d030 0x030>;
#clock-cells = <1>;
#reset-cells = <1>;
clocks = <&ccu_pll CCU_SATA_PLL>,
<&ccu_pll CCU_PCIE_PLL>,
<&ccu_pll CCU_ETH_PLL>;
clock-names = "sata_clk", "pcie_clk", "eth_clk";
};
# System Devices Clock Control Unit node:
- |
#include <dt-bindings/clock/bt1-ccu.h>
clock-controller@1f04d060 {
compatible = "baikal,bt1-ccu-sys";
reg = <0x1f04d060 0x0a0>;
#clock-cells = <1>;
#reset-cells = <1>;
clocks = <&clk25m>,
<&ccu_pll CCU_SATA_PLL>,
<&ccu_pll CCU_PCIE_PLL>,
<&ccu_pll CCU_ETH_PLL>;
clock-names = "ref_clk", "sata_clk", "pcie_clk",
"eth_clk";
};
# Required Clock Control Unit PLL node:
- |
ccu_pll: clock-controller@1f04d000 {
compatible = "baikal,bt1-ccu-pll";
reg = <0x1f04d000 0x028>;
#clock-cells = <1>;
clocks = <&clk25m>;
clock-names = "ref_clk";
};
...