Documentation/devicetree/bindings/opp/opp.txt - linux/kernel/git/jmorris/linux-security - Git at Google

 Generic OPP (Operating Performance Points) Bindings
 ----------------------------------------------------

 Devices work at voltage-current-frequency combinations and some implementations
 have the liberty of choosing these. These combinations are called Operating
 Performance Points aka OPPs. This document defines bindings for these OPPs
 applicable across wide range of devices. For illustration purpose, this document
 uses CPU as a device.

 This document contain multiple versions of OPP binding and only one of them
 should be used per device.

 Binding 1: operating-points
 ============================

 This binding only supports voltage-frequency pairs.

 Properties:
 - operating-points: An array of 2-tuples items, and each item consists
   of frequency and voltage like <freq-kHz vol-uV>.
 	freq: clock frequency in kHz
 	vol: voltage in microvolt

 Examples:

 cpu@0 {
 	compatible = "arm,cortex-a9";
 	reg = <0>;
 	next-level-cache = <&L2>;
 	operating-points = <
 		/* kHz    uV */
 		792000  1100000
 		396000  950000
 		198000  850000
 	>;
 };


 Binding 2: operating-points-v2
 ============================

 * Property: operating-points-v2

 Devices supporting OPPs must set their "operating-points-v2" property with
 phandle to a OPP table in their DT node. The OPP core will use this phandle to
 find the operating points for the device.

 If required, this can be extended for SoC vendor specific bindings. Such bindings
 should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt
 and should have a compatible description like: "operating-points-v2-<vendor>".

 * OPP Table Node

 This describes the OPPs belonging to a device. This node can have following
 properties:

 Required properties:
 - compatible: Allow OPPs to express their compatibility. It should be:
   "operating-points-v2".

 - OPP nodes: One or more OPP nodes describing voltage-current-frequency
   combinations. Their name isn't significant but their phandle can be used to
   reference an OPP.

 Optional properties:
 - opp-shared: Indicates that device nodes using this OPP Table Node's phandle
   switch their DVFS state together, i.e. they share clock/voltage/current lines.
   Missing property means devices have independent clock/voltage/current lines,
   but they share OPP tables.

 - status: Marks the OPP table enabled/disabled.


 * OPP Node

 This defines voltage-current-frequency combinations along with other related
 properties.

 Required properties:
 - opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer.

 Optional properties:
 - opp-microvolt: voltage in micro Volts.

   A single regulator's voltage is specified with an array of size one or three.
   Single entry is for target voltage and three entries are for <target min max>
   voltages.

   Entries for multiple regulators shall be provided in the same field separated
   by angular brackets <>. The OPP binding doesn't provide any provisions to
   relate the values to their power supplies or the order in which the supplies
   need to be configured and that is left for the implementation specific
   binding.

   Entries for all regulators shall be of the same size, i.e. either all use a
   single value or triplets.

 - opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to
   the above opp-microvolt property, but allows multiple voltage ranges to be
   provided for the same OPP. At runtime, the platform can pick a <name> and
   matching opp-microvolt-<name> property will be enabled for all OPPs. If the
   platform doesn't pick a specific <name> or the <name> doesn't match with any
   opp-microvolt-<name> properties, then opp-microvolt property shall be used, if
   present.

 - opp-microamp: The maximum current drawn by the device in microamperes
   considering system specific parameters (such as transients, process, aging,
   maximum operating temperature range etc.) as necessary. This may be used to
   set the most efficient regulator operating mode.

   Should only be set if opp-microvolt is set for the OPP.

   Entries for multiple regulators shall be provided in the same field separated
   by angular brackets <>. If current values aren't required for a regulator,
   then it shall be filled with 0. If current values aren't required for any of
   the regulators, then this field is not required. The OPP binding doesn't
   provide any provisions to relate the values to their power supplies or the
   order in which the supplies need to be configured and that is left for the
   implementation specific binding.

 - opp-microamp-<name>: Named opp-microamp property. Similar to
   opp-microvolt-<name> property, but for microamp instead.

 - clock-latency-ns: Specifies the maximum possible transition latency (in
   nanoseconds) for switching to this OPP from any other OPP.

 - turbo-mode: Marks the OPP to be used only for turbo modes. Turbo mode is
   available on some platforms, where the device can run over its operating
   frequency for a short duration of time limited by the device's power, current
   and thermal limits.

 - opp-suspend: Marks the OPP to be used during device suspend. Only one OPP in
   the table should have this.

 - opp-supported-hw: This enables us to select only a subset of OPPs from the
   larger OPP table, based on what version of the hardware we are running on. We
   still can't have multiple nodes with the same opp-hz value in OPP table.

   It's a user defined array containing a hierarchy of hardware version numbers,
   supported by the OPP. For example: a platform with hierarchy of three levels
   of versions (A, B and C), this field should be like <X Y Z>, where X
   corresponds to Version hierarchy A, Y corresponds to version hierarchy B and Z
   corresponds to version hierarchy C.

   Each level of hierarchy is represented by a 32 bit value, and so there can be
   only 32 different supported version per hierarchy. i.e. 1 bit per version. A
   value of 0xFFFFFFFF will enable the OPP for all versions for that hierarchy
   level. And a value of 0x00000000 will disable the OPP completely, and so we
   never want that to happen.

   If 32 values aren't sufficient for a version hierarchy, than that version
   hierarchy can be contained in multiple 32 bit values. i.e. <X Y Z1 Z2> in the
   above example, Z1 & Z2 refer to the version hierarchy Z.

 - status: Marks the node enabled/disabled.

 Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together.

 / {
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

 		cpu@0 {
 			compatible = "arm,cortex-a9";
 			reg = <0>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 0>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};

 		cpu@1 {
 			compatible = "arm,cortex-a9";
 			reg = <1>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 0>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};

 	cpu0_opp_table: opp_table0 {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <975000 970000 985000>;
 			opp-microamp = <70000>;
 			clock-latency-ns = <300000>;
 			opp-suspend;
 		};
 		opp-1100000000 {
 			opp-hz = /bits/ 64 <1100000000>;
 			opp-microvolt = <1000000 980000 1010000>;
 			opp-microamp = <80000>;
 			clock-latency-ns = <310000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <1025000>;
 			clock-latency-ns = <290000>;
 			turbo-mode;
 		};
 	};
 };

 Example 2: Single cluster, Quad-core Qualcom-krait, switches DVFS states
 independently.

 / {
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

 		cpu@0 {
 			compatible = "qcom,krait";
 			reg = <0>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 0>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply0>;
 			operating-points-v2 = <&cpu_opp_table>;
 		};

 		cpu@1 {
 			compatible = "qcom,krait";
 			reg = <1>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 1>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply1>;
 			operating-points-v2 = <&cpu_opp_table>;
 		};

 		cpu@2 {
 			compatible = "qcom,krait";
 			reg = <2>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 2>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply2>;
 			operating-points-v2 = <&cpu_opp_table>;
 		};

 		cpu@3 {
 			compatible = "qcom,krait";
 			reg = <3>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 3>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply3>;
 			operating-points-v2 = <&cpu_opp_table>;
 		};
 	};

 	cpu_opp_table: opp_table {
 		compatible = "operating-points-v2";

 		/*
 		 * Missing opp-shared property means CPUs switch DVFS states
 		 * independently.
 		 */

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <975000 970000 985000>;
 			opp-microamp = <70000>;
 			clock-latency-ns = <300000>;
 			opp-suspend;
 		};
 		opp-1100000000 {
 			opp-hz = /bits/ 64 <1100000000>;
 			opp-microvolt = <1000000 980000 1010000>;
 			opp-microamp = <80000>;
 			clock-latency-ns = <310000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <1025000>;
 			opp-microamp = <90000;
 			lock-latency-ns = <290000>;
 			turbo-mode;
 		};
 	};
 };

 Example 3: Dual-cluster, Dual-core per cluster. CPUs within a cluster switch
 DVFS state together.

 / {
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

 		cpu@0 {
 			compatible = "arm,cortex-a7";
 			reg = <0>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 0>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply0>;
 			operating-points-v2 = <&cluster0_opp>;
 		};

 		cpu@1 {
 			compatible = "arm,cortex-a7";
 			reg = <1>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 0>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply0>;
 			operating-points-v2 = <&cluster0_opp>;
 		};

 		cpu@100 {
 			compatible = "arm,cortex-a15";
 			reg = <100>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 1>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply1>;
 			operating-points-v2 = <&cluster1_opp>;
 		};

 		cpu@101 {
 			compatible = "arm,cortex-a15";
 			reg = <101>;
 			next-level-cache = <&L2>;
 			clocks = <&clk_controller 1>;
 			clock-names = "cpu";
 			cpu-supply = <&cpu_supply1>;
 			operating-points-v2 = <&cluster1_opp>;
 		};
 	};

 	cluster0_opp: opp_table0 {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <975000 970000 985000>;
 			opp-microamp = <70000>;
 			clock-latency-ns = <300000>;
 			opp-suspend;
 		};
 		opp-1100000000 {
 			opp-hz = /bits/ 64 <1100000000>;
 			opp-microvolt = <1000000 980000 1010000>;
 			opp-microamp = <80000>;
 			clock-latency-ns = <310000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <1025000>;
 			opp-microamp = <90000>;
 			clock-latency-ns = <290000>;
 			turbo-mode;
 		};
 	};

 	cluster1_opp: opp_table1 {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
 			opp-microvolt = <1050000 1045000 1055000>;
 			opp-microamp = <95000>;
 			clock-latency-ns = <400000>;
 			opp-suspend;
 		};
 		opp-1400000000 {
 			opp-hz = /bits/ 64 <1400000000>;
 			opp-microvolt = <1075000>;
 			opp-microamp = <100000>;
 			clock-latency-ns = <400000>;
 		};
 		opp-1500000000 {
 			opp-hz = /bits/ 64 <1500000000>;
 			opp-microvolt = <1100000 1010000 1110000>;
 			opp-microamp = <95000>;
 			clock-latency-ns = <400000>;
 			turbo-mode;
 		};
 	};
 };

 Example 4: Handling multiple regulators

 / {
 	cpus {
 		cpu@0 {
 			compatible = "vendor,cpu-type";
 			...

 			vcc0-supply = <&cpu_supply0>;
 			vcc1-supply = <&cpu_supply1>;
 			vcc2-supply = <&cpu_supply2>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};

 	cpu0_opp_table: opp_table0 {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <970000>, /* Supply 0 */
 					<960000>, /* Supply 1 */
 					<960000>; /* Supply 2 */
 			opp-microamp =  <70000>,  /* Supply 0 */
 					<70000>,  /* Supply 1 */
 					<70000>;  /* Supply 2 */
 			clock-latency-ns = <300000>;
 		};

 		/* OR */

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <975000 970000 985000>, /* Supply 0 */
 					<965000 960000 975000>, /* Supply 1 */
 					<965000 960000 975000>; /* Supply 2 */
 			opp-microamp =  <70000>,		/* Supply 0 */
 					<70000>,		/* Supply 1 */
 					<70000>;		/* Supply 2 */
 			clock-latency-ns = <300000>;
 		};

 		/* OR */

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <975000 970000 985000>, /* Supply 0 */
 					<965000 960000 975000>, /* Supply 1 */
 					<965000 960000 975000>; /* Supply 2 */
 			opp-microamp =  <70000>,		/* Supply 0 */
 					<0>,			/* Supply 1 doesn't need this */
 					<70000>;		/* Supply 2 */
 			clock-latency-ns = <300000>;
 		};
 	};
 };

 Example 5: opp-supported-hw
 (example: three level hierarchy of versions: cuts, substrate and process)

 / {
 	cpus {
 		cpu@0 {
 			compatible = "arm,cortex-a7";
 			...

 			cpu-supply = <&cpu_supply>
 			operating-points-v2 = <&cpu0_opp_table_slow>;
 		};
 	};

 	opp_table {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-600000000 {
 			/*
 			 * Supports all substrate and process versions for 0xF
 			 * cuts, i.e. only first four cuts.
 			 */
 			opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF>
 			opp-hz = /bits/ 64 <600000000>;
 			opp-microvolt = <915000 900000 925000>;
 			...
 		};

 		opp-800000000 {
 			/*
 			 * Supports:
 			 * - cuts: only one, 6th cut (represented by 6th bit).
 			 * - substrate: supports 16 different substrate versions
 			 * - process: supports 9 different process versions
 			 */
 			opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0>
 			opp-hz = /bits/ 64 <800000000>;
 			opp-microvolt = <915000 900000 925000>;
 			...
 		};
 	};
 };

 Example 6: opp-microvolt-<name>, opp-microamp-<name>:
 (example: device with two possible microvolt ranges: slow and fast)

 / {
 	cpus {
 		cpu@0 {
 			compatible = "arm,cortex-a7";
 			...

 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};

 	cpu0_opp_table: opp_table0 {
 		compatible = "operating-points-v2";
 		opp-shared;

 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt-slow = <915000 900000 925000>;
 			opp-microvolt-fast = <975000 970000 985000>;
 			opp-microamp-slow =  <70000>;
 			opp-microamp-fast =  <71000>;
 		};

 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */
 					      <925000 910000 935000>; /* Supply vcc1 */
 			opp-microvolt-fast = <975000 970000 985000>, /* Supply vcc0 */
 					     <965000 960000 975000>; /* Supply vcc1 */
 			opp-microamp =  <70000>; /* Will be used for both slow/fast */
 		};
 	};
 };
	Generic OPP (Operating Performance Points) Bindings
	----------------------------------------------------

	Devices work at voltage-current-frequency combinations and some implementations
	have the liberty of choosing these. These combinations are called Operating
	Performance Points aka OPPs. This document defines bindings for these OPPs
	applicable across wide range of devices. For illustration purpose, this document
	uses CPU as a device.

	This document contain multiple versions of OPP binding and only one of them
	should be used per device.

	Binding 1: operating-points
	============================

	This binding only supports voltage-frequency pairs.

	Properties:
	- operating-points: An array of 2-tuples items, and each item consists
	of frequency and voltage like <freq-kHz vol-uV>.
	freq: clock frequency in kHz
	vol: voltage in microvolt

	Examples:

	cpu@0 {
	compatible = "arm,cortex-a9";
	reg = <0>;
	next-level-cache = <&L2>;
	operating-points = <
	/* kHz uV */
	792000 1100000
	396000 950000
	198000 850000
	>;
	};


	Binding 2: operating-points-v2
	============================

	* Property: operating-points-v2

	Devices supporting OPPs must set their "operating-points-v2" property with
	phandle to a OPP table in their DT node. The OPP core will use this phandle to
	find the operating points for the device.

	If required, this can be extended for SoC vendor specific bindings. Such bindings
	should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt
	and should have a compatible description like: "operating-points-v2-<vendor>".

	* OPP Table Node

	This describes the OPPs belonging to a device. This node can have following
	properties:

	Required properties:
	- compatible: Allow OPPs to express their compatibility. It should be:
	"operating-points-v2".

	- OPP nodes: One or more OPP nodes describing voltage-current-frequency
	combinations. Their name isn't significant but their phandle can be used to
	reference an OPP.

	Optional properties:
	- opp-shared: Indicates that device nodes using this OPP Table Node's phandle
	switch their DVFS state together, i.e. they share clock/voltage/current lines.
	Missing property means devices have independent clock/voltage/current lines,
	but they share OPP tables.

	- status: Marks the OPP table enabled/disabled.


	* OPP Node

	This defines voltage-current-frequency combinations along with other related
	properties.

	Required properties:
	- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer.

	Optional properties:
	- opp-microvolt: voltage in micro Volts.

	A single regulator's voltage is specified with an array of size one or three.
	Single entry is for target voltage and three entries are for <target min max>
	voltages.

	Entries for multiple regulators shall be provided in the same field separated
	by angular brackets <>. The OPP binding doesn't provide any provisions to
	relate the values to their power supplies or the order in which the supplies
	need to be configured and that is left for the implementation specific
	binding.

	Entries for all regulators shall be of the same size, i.e. either all use a
	single value or triplets.

	- opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to
	the above opp-microvolt property, but allows multiple voltage ranges to be
	provided for the same OPP. At runtime, the platform can pick a <name> and
	matching opp-microvolt-<name> property will be enabled for all OPPs. If the
	platform doesn't pick a specific <name> or the <name> doesn't match with any
	opp-microvolt-<name> properties, then opp-microvolt property shall be used, if
	present.

	- opp-microamp: The maximum current drawn by the device in microamperes
	considering system specific parameters (such as transients, process, aging,
	maximum operating temperature range etc.) as necessary. This may be used to
	set the most efficient regulator operating mode.

	Should only be set if opp-microvolt is set for the OPP.

	Entries for multiple regulators shall be provided in the same field separated
	by angular brackets <>. If current values aren't required for a regulator,
	then it shall be filled with 0. If current values aren't required for any of
	the regulators, then this field is not required. The OPP binding doesn't
	provide any provisions to relate the values to their power supplies or the
	order in which the supplies need to be configured and that is left for the
	implementation specific binding.

	- opp-microamp-<name>: Named opp-microamp property. Similar to
	opp-microvolt-<name> property, but for microamp instead.

	- clock-latency-ns: Specifies the maximum possible transition latency (in
	nanoseconds) for switching to this OPP from any other OPP.

	- turbo-mode: Marks the OPP to be used only for turbo modes. Turbo mode is
	available on some platforms, where the device can run over its operating
	frequency for a short duration of time limited by the device's power, current
	and thermal limits.

	- opp-suspend: Marks the OPP to be used during device suspend. Only one OPP in
	the table should have this.

	- opp-supported-hw: This enables us to select only a subset of OPPs from the
	larger OPP table, based on what version of the hardware we are running on. We
	still can't have multiple nodes with the same opp-hz value in OPP table.

	It's a user defined array containing a hierarchy of hardware version numbers,
	supported by the OPP. For example: a platform with hierarchy of three levels
	of versions (A, B and C), this field should be like <X Y Z>, where X
	corresponds to Version hierarchy A, Y corresponds to version hierarchy B and Z
	corresponds to version hierarchy C.

	Each level of hierarchy is represented by a 32 bit value, and so there can be
	only 32 different supported version per hierarchy. i.e. 1 bit per version. A
	value of 0xFFFFFFFF will enable the OPP for all versions for that hierarchy
	level. And a value of 0x00000000 will disable the OPP completely, and so we
	never want that to happen.

	If 32 values aren't sufficient for a version hierarchy, than that version
	hierarchy can be contained in multiple 32 bit values. i.e. <X Y Z1 Z2> in the
	above example, Z1 & Z2 refer to the version hierarchy Z.

	- status: Marks the node enabled/disabled.

	Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together.

	/ {
	cpus {
	#address-cells = <1>;
	#size-cells = <0>;

	cpu@0 {
	compatible = "arm,cortex-a9";
	reg = <0>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 0>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply0>;
	operating-points-v2 = <&cpu0_opp_table>;
	};

	cpu@1 {
	compatible = "arm,cortex-a9";
	reg = <1>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 0>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply0>;
	operating-points-v2 = <&cpu0_opp_table>;
	};
	};

	cpu0_opp_table: opp_table0 {
	compatible = "operating-points-v2";
	opp-shared;

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <975000 970000 985000>;
	opp-microamp = <70000>;
	clock-latency-ns = <300000>;
	opp-suspend;
	};
	opp-1100000000 {
	opp-hz = /bits/ 64 <1100000000>;
	opp-microvolt = <1000000 980000 1010000>;
	opp-microamp = <80000>;
	clock-latency-ns = <310000>;
	};
	opp-1200000000 {
	opp-hz = /bits/ 64 <1200000000>;
	opp-microvolt = <1025000>;
	clock-latency-ns = <290000>;
	turbo-mode;
	};
	};
	};

	Example 2: Single cluster, Quad-core Qualcom-krait, switches DVFS states
	independently.

	/ {
	cpus {
	#address-cells = <1>;
	#size-cells = <0>;

	cpu@0 {
	compatible = "qcom,krait";
	reg = <0>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 0>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply0>;
	operating-points-v2 = <&cpu_opp_table>;
	};

	cpu@1 {
	compatible = "qcom,krait";
	reg = <1>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 1>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply1>;
	operating-points-v2 = <&cpu_opp_table>;
	};

	cpu@2 {
	compatible = "qcom,krait";
	reg = <2>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 2>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply2>;
	operating-points-v2 = <&cpu_opp_table>;
	};

	cpu@3 {
	compatible = "qcom,krait";
	reg = <3>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 3>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply3>;
	operating-points-v2 = <&cpu_opp_table>;
	};
	};

	cpu_opp_table: opp_table {
	compatible = "operating-points-v2";

	/*
	* Missing opp-shared property means CPUs switch DVFS states
	* independently.
	*/

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <975000 970000 985000>;
	opp-microamp = <70000>;
	clock-latency-ns = <300000>;
	opp-suspend;
	};
	opp-1100000000 {
	opp-hz = /bits/ 64 <1100000000>;
	opp-microvolt = <1000000 980000 1010000>;
	opp-microamp = <80000>;
	clock-latency-ns = <310000>;
	};
	opp-1200000000 {
	opp-hz = /bits/ 64 <1200000000>;
	opp-microvolt = <1025000>;
	opp-microamp = <90000;
	lock-latency-ns = <290000>;
	turbo-mode;
	};
	};
	};

	Example 3: Dual-cluster, Dual-core per cluster. CPUs within a cluster switch
	DVFS state together.

	/ {
	cpus {
	#address-cells = <1>;
	#size-cells = <0>;

	cpu@0 {
	compatible = "arm,cortex-a7";
	reg = <0>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 0>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply0>;
	operating-points-v2 = <&cluster0_opp>;
	};

	cpu@1 {
	compatible = "arm,cortex-a7";
	reg = <1>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 0>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply0>;
	operating-points-v2 = <&cluster0_opp>;
	};

	cpu@100 {
	compatible = "arm,cortex-a15";
	reg = <100>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 1>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply1>;
	operating-points-v2 = <&cluster1_opp>;
	};

	cpu@101 {
	compatible = "arm,cortex-a15";
	reg = <101>;
	next-level-cache = <&L2>;
	clocks = <&clk_controller 1>;
	clock-names = "cpu";
	cpu-supply = <&cpu_supply1>;
	operating-points-v2 = <&cluster1_opp>;
	};
	};

	cluster0_opp: opp_table0 {
	compatible = "operating-points-v2";
	opp-shared;

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <975000 970000 985000>;
	opp-microamp = <70000>;
	clock-latency-ns = <300000>;
	opp-suspend;
	};
	opp-1100000000 {
	opp-hz = /bits/ 64 <1100000000>;
	opp-microvolt = <1000000 980000 1010000>;
	opp-microamp = <80000>;
	clock-latency-ns = <310000>;
	};
	opp-1200000000 {
	opp-hz = /bits/ 64 <1200000000>;
	opp-microvolt = <1025000>;
	opp-microamp = <90000>;
	clock-latency-ns = <290000>;
	turbo-mode;
	};
	};

	cluster1_opp: opp_table1 {
	compatible = "operating-points-v2";
	opp-shared;

	opp-1300000000 {
	opp-hz = /bits/ 64 <1300000000>;
	opp-microvolt = <1050000 1045000 1055000>;
	opp-microamp = <95000>;
	clock-latency-ns = <400000>;
	opp-suspend;
	};
	opp-1400000000 {
	opp-hz = /bits/ 64 <1400000000>;
	opp-microvolt = <1075000>;
	opp-microamp = <100000>;
	clock-latency-ns = <400000>;
	};
	opp-1500000000 {
	opp-hz = /bits/ 64 <1500000000>;
	opp-microvolt = <1100000 1010000 1110000>;
	opp-microamp = <95000>;
	clock-latency-ns = <400000>;
	turbo-mode;
	};
	};
	};

	Example 4: Handling multiple regulators

	/ {
	cpus {
	cpu@0 {
	compatible = "vendor,cpu-type";
	...

	vcc0-supply = <&cpu_supply0>;
	vcc1-supply = <&cpu_supply1>;
	vcc2-supply = <&cpu_supply2>;
	operating-points-v2 = <&cpu0_opp_table>;
	};
	};

	cpu0_opp_table: opp_table0 {
	compatible = "operating-points-v2";
	opp-shared;

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <970000>, /* Supply 0 */
	<960000>, /* Supply 1 */
	<960000>; /* Supply 2 */
	opp-microamp = <70000>, /* Supply 0 */
	<70000>, /* Supply 1 */
	<70000>; /* Supply 2 */
	clock-latency-ns = <300000>;
	};

	/* OR */

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <975000 970000 985000>, /* Supply 0 */
	<965000 960000 975000>, /* Supply 1 */
	<965000 960000 975000>; /* Supply 2 */
	opp-microamp = <70000>, /* Supply 0 */
	<70000>, /* Supply 1 */
	<70000>; /* Supply 2 */
	clock-latency-ns = <300000>;
	};

	/* OR */

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt = <975000 970000 985000>, /* Supply 0 */
	<965000 960000 975000>, /* Supply 1 */
	<965000 960000 975000>; /* Supply 2 */
	opp-microamp = <70000>, /* Supply 0 */
	<0>, /* Supply 1 doesn't need this */
	<70000>; /* Supply 2 */
	clock-latency-ns = <300000>;
	};
	};
	};

	Example 5: opp-supported-hw
	(example: three level hierarchy of versions: cuts, substrate and process)

	/ {
	cpus {
	cpu@0 {
	compatible = "arm,cortex-a7";
	...

	cpu-supply = <&cpu_supply>
	operating-points-v2 = <&cpu0_opp_table_slow>;
	};
	};

	opp_table {
	compatible = "operating-points-v2";
	opp-shared;

	opp-600000000 {
	/*
	* Supports all substrate and process versions for 0xF
	* cuts, i.e. only first four cuts.
	*/
	opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF>
	opp-hz = /bits/ 64 <600000000>;
	opp-microvolt = <915000 900000 925000>;
	...
	};

	opp-800000000 {
	/*
	* Supports:
	* - cuts: only one, 6th cut (represented by 6th bit).
	* - substrate: supports 16 different substrate versions
	* - process: supports 9 different process versions
	*/
	opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0>
	opp-hz = /bits/ 64 <800000000>;
	opp-microvolt = <915000 900000 925000>;
	...
	};
	};
	};

	Example 6: opp-microvolt-<name>, opp-microamp-<name>:
	(example: device with two possible microvolt ranges: slow and fast)

	/ {
	cpus {
	cpu@0 {
	compatible = "arm,cortex-a7";
	...

	operating-points-v2 = <&cpu0_opp_table>;
	};
	};

	cpu0_opp_table: opp_table0 {
	compatible = "operating-points-v2";
	opp-shared;

	opp-1000000000 {
	opp-hz = /bits/ 64 <1000000000>;
	opp-microvolt-slow = <915000 900000 925000>;
	opp-microvolt-fast = <975000 970000 985000>;
	opp-microamp-slow = <70000>;
	opp-microamp-fast = <71000>;
	};

	opp-1200000000 {
	opp-hz = /bits/ 64 <1200000000>;
	opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */
	<925000 910000 935000>; /* Supply vcc1 */
	opp-microvolt-fast = <975000 970000 985000>, /* Supply vcc0 */
	<965000 960000 975000>; /* Supply vcc1 */
	opp-microamp = <70000>; /* Will be used for both slow/fast */
	};
	};
	};