blob: 57dfda8a7a1da5cb0a4799882f75a154dd2750af [file] [log] [blame]
TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
OMAP CONTROL PHY
Required properties:
- compatible: Should be one of
"ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
"ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
e.g. USB2_PHY on OMAP5.
"ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
e.g. USB3 PHY and SATA PHY on OMAP5.
"ti,control-phy-pcie" - for pcie to support external clock for pcie and to
set PCS delay value.
e.g. PCIE PHY in DRA7x
"ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
DRA7 platform.
"ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
AM437 platform.
- reg : register ranges as listed in the reg-names property
- reg-names: "otghs_control" for control-phy-otghs
"power", "pcie_pcs" and "control_sma" for control-phy-pcie
"power" for all other types
omap_control_usb: omap-control-usb@4a002300 {
compatible = "ti,control-phy-otghs";
reg = <0x4a00233c 0x4>;
reg-names = "otghs_control";
};
OMAP USB2 PHY
Required properties:
- compatible: Should be "ti,omap-usb2"
Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on
DRA7x
Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY
in DRA7x
- reg : Address and length of the register set for the device.
- #phy-cells: determine the number of cells that should be given in the
phandle while referencing this phy.
- clocks: a list of phandles and clock-specifier pairs, one for each entry in
clock-names.
- clock-names: should include:
* "wkupclk" - wakeup clock.
* "refclk" - reference clock (optional).
Deprecated properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
the PHY.
Recommended properies:
- syscon-phy-power : phandle/offset pair. Phandle to the system control
module and the register offset to power on/off the PHY.
This is usually a subnode of ocp2scp to which it is connected.
usb2phy@4a0ad080 {
compatible = "ti,omap-usb2";
reg = <0x4a0ad080 0x58>;
ctrl-module = <&omap_control_usb>;
#phy-cells = <0>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
};
TI PIPE3 PHY
Required properties:
- compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
"ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
- reg : Address and length of the register set for the device.
- reg-names: The names of the register addresses corresponding to the registers
filled in "reg".
- #phy-cells: determine the number of cells that should be given in the
phandle while referencing this phy.
- clocks: a list of phandles and clock-specifier pairs, one for each entry in
clock-names.
- clock-names: should include:
* "wkupclk" - wakeup clock.
* "sysclk" - system clock.
* "refclk" - reference clock.
* "dpll_ref" - external dpll ref clk
* "dpll_ref_m2" - external dpll ref clk
* "phy-div" - divider for apll
* "div-clk" - apll clock
Optional properties:
- id: If there are multiple instance of the same type, in order to
differentiate between each instance "id" can be used (e.g., multi-lane PCIe
PHY). If "id" is not provided, it is set to default value of '1'.
- syscon-pllreset: Handle to system control region that contains the
CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
- syscon-pcs : phandle/offset pair. Phandle to the system control module and the
register offset to write the PCS delay value.
Deprecated properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
the PHY.
Recommended properies:
- syscon-phy-power : phandle/offset pair. Phandle to the system control
module and the register offset to power on/off the PHY.
This is usually a subnode of ocp2scp to which it is connected.
usb3phy@4a084400 {
compatible = "ti,phy-usb3";
reg = <0x4a084400 0x80>,
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_usb>;
#phy-cells = <0>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
clock-names = "wkupclk",
"sysclk",
"refclk";
};
sata_phy: phy@4a096000 {
compatible = "ti,phy-pipe3-sata";
reg = <0x4A096000 0x80>, /* phy_rx */
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_sata>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
#phy-cells = <0>;
};