| GigaSet 307x Device Driver |
| ========================== |
| |
| 1. Requirements |
| ------------ |
| 1.1. Hardware |
| -------- |
| This release supports the connection of the Gigaset 307x/417x family of |
| ISDN DECT bases via Gigaset M101 Data, Gigaset M105 Data or direct USB |
| connection. The following devices are reported to be compatible: |
| 307x/417x: |
| Gigaset SX255isdn |
| Gigaset SX353isdn |
| Sinus 45 [AB] isdn (Deutsche Telekom) |
| Sinus 721X/XA |
| Vox Chicago 390 ISDN (KPN Telecom) |
| M101: |
| Sinus 45 Data 1 (Telekom) |
| M105: |
| Gigaset USB Adapter DECT |
| Sinus 45 Data 2 (Telekom) |
| Sinus 721 data |
| Chicago 390 USB (KPN) |
| See also http://www.erbze.info/sinus_gigaset.htm and |
| http://gigaset307x.sourceforge.net/ |
| |
| We had also reports from users of Gigaset M105 who could use the drivers |
| with SX 100 and CX 100 ISDN bases (only in unimodem mode, see section 2.4.) |
| If you have another device that works with our driver, please let us know. |
| For example, Gigaset SX205isdn/Sinus 721 X SE and Gigaset SX303isdn bases |
| are just versions without answering machine of models known to work, so |
| they should work just as well; but so far we are lacking positive reports |
| on these. |
| |
| Chances of getting an USB device to work are good if the output of |
| lsusb |
| at the command line contains one of the following: |
| ID 0681:0001 |
| ID 0681:0002 |
| ID 0681:0009 |
| ID 0681:0021 |
| ID 0681:0022 |
| |
| 1.2. Software |
| -------- |
| The driver works with ISDN4linux and so can be used with any software |
| which is able to use ISDN4linux for ISDN connections (voice or data). |
| CAPI4Linux support is planned but not yet available. |
| |
| There are some user space tools available at |
| http://sourceforge.net/projects/gigaset307x/ |
| which provide access to additional device specific functions like SMS, |
| phonebook or call journal. |
| |
| |
| 2. How to use the driver |
| --------------------- |
| 2.1. Modules |
| ------- |
| To get the device working, you have to load the proper kernel module. You |
| can do this using |
| modprobe modulename |
| where modulename is usb_gigaset (M105) or bas_gigaset (direct USB |
| connection to the base). |
| |
| 2.2. Device nodes for user space programs |
| ------------------------------------ |
| The device can be accessed from user space (eg. by the user space tools |
| mentioned in 1.2.) through the device nodes: |
| |
| - /dev/ttyGU0 for M105 (USB data boxes) |
| - /dev/ttyGB0 for the base driver (direct USB connection) |
| |
| You can also select a "default device" which is used by the frontends when |
| no device node is given as parameter, by creating a symlink /dev/ttyG to |
| one of them, eg.: |
| |
| ln -s /dev/ttyGB0 /dev/ttyG |
| |
| 2.3. ISDN4linux |
| ---------- |
| This is the "normal" mode of operation. After loading the module you can |
| set up the ISDN system just as you'd do with any ISDN card. |
| Your distribution should provide some configuration utility. |
| If not, you can use some HOWTOs like |
| http://www.linuxhaven.de/dlhp/HOWTO/DE-ISDN-HOWTO-5.html |
| If this doesn't work, because you have some recent device like SX100 where |
| debug output (see section 3.2.) shows something like this when dialing |
| CMD Received: ERROR |
| Available Params: 0 |
| Connection State: 0, Response: -1 |
| gigaset_process_response: resp_code -1 in ConState 0 ! |
| Timeout occurred |
| you might need to use unimodem mode: |
| |
| 2.4. Unimodem mode |
| ------------- |
| This is needed for some devices [e.g. SX100] as they have problems with |
| the "normal" commands. |
| |
| If you have installed the command line tool gigacontr, you can enter |
| unimodem mode using |
| gigacontr --mode unimodem |
| You can switch back using |
| gigacontr --mode isdn |
| |
| You can also load the driver using e.g. |
| modprobe usb_gigaset startmode=0 |
| to prevent the driver from starting in "isdn4linux mode". |
| |
| In this mode the device works like a modem connected to a serial port |
| (the /dev/ttyGU0, ... mentioned above) which understands the commands |
| ATZ init, reset |
| => OK or ERROR |
| ATD |
| ATDT dial |
| => OK, CONNECT, |
| BUSY, |
| NO DIAL TONE, |
| NO CARRIER, |
| NO ANSWER |
| <pause>+++<pause> change to command mode when connected |
| ATH hangup |
| |
| You can use some configuration tool of your distribution to configure this |
| "modem" or configure pppd/wvdial manually. There are some example ppp |
| configuration files and chat scripts in the gigaset-VERSION/ppp directory |
| in the driver packages from http://sourceforge.net/projects/gigaset307x/. |
| Please note that the USB drivers are not able to change the state of the |
| control lines (the M105 driver can be configured to use some undocumented |
| control requests, if you really need the control lines, though). This means |
| you must use "Stupid Mode" if you are using wvdial or you should use the |
| nocrtscts option of pppd. |
| You must also assure that the ppp_async module is loaded with the parameter |
| flag_time=0. You can do this e.g. by adding a line like |
| |
| options ppp_async flag_time=0 |
| |
| to /etc/modprobe.conf. If your distribution has some local module |
| configuration file like /etc/modprobe.conf.local, |
| using that should be preferred. |
| |
| 2.5. Call-ID (CID) mode |
| ------------------ |
| Call-IDs are numbers used to tag commands to, and responses from, the |
| Gigaset base in order to support the simultaneous handling of multiple |
| ISDN calls. Their use can be enabled ("CID mode") or disabled ("Unimodem |
| mode"). Without Call-IDs (in Unimodem mode), only a very limited set of |
| functions is available. It allows outgoing data connections only, but |
| does not signal incoming calls or other base events. |
| |
| DECT cordless data devices (M10x) permanently occupy the cordless |
| connection to the base while Call-IDs are activated. As the Gigaset |
| bases only support one DECT data connection at a time, this prevents |
| other DECT cordless data devices from accessing the base. |
| |
| During active operation, the driver switches to the necessary mode |
| automatically. However, for the reasons above, the mode chosen when |
| the device is not in use (idle) can be selected by the user. |
| - If you want to receive incoming calls, you can use the default |
| settings (CID mode). |
| - If you have several DECT data devices (M10x) which you want to use |
| in turn, select Unimodem mode by passing the parameter "cidmode=0" to |
| the driver ("modprobe usb_gigaset cidmode=0" or modprobe.conf). |
| |
| If you want both of these at once, you are out of luck. |
| |
| You can also use /sys/class/tty/ttyGxy/cidmode for changing the CID mode |
| setting (ttyGxy is ttyGU0 or ttyGB0). |
| |
| |
| 3. Troubleshooting |
| --------------- |
| 3.1. Solutions to frequently reported problems |
| ----------------------------------------- |
| Problem: |
| You have a slow provider and isdn4linux gives up dialing too early. |
| Solution: |
| Load the isdn module using the dialtimeout option. You can do this e.g. |
| by adding a line like |
| |
| options isdn dialtimeout=15 |
| |
| to /etc/modprobe.conf. If your distribution has some local module |
| configuration file like /etc/modprobe.conf.local, |
| using that should be preferred. |
| |
| Problem: |
| Your isdn script aborts with a message about isdnlog. |
| Solution: |
| Try deactivating (or commenting out) isdnlog. This driver does not |
| support it. |
| |
| Problem: |
| You have two or more DECT data adapters (M101/M105) and only the |
| first one you turn on works. |
| Solution: |
| Select Unimodem mode for all DECT data adapters. (see section 2.4.) |
| |
| 3.2. Telling the driver to provide more information |
| ---------------------------------------------- |
| Building the driver with the "Gigaset debugging" kernel configuration |
| option (CONFIG_GIGASET_DEBUG) gives it the ability to produce additional |
| information useful for debugging. |
| |
| You can control the amount of debugging information the driver produces by |
| writing an appropriate value to /sys/module/gigaset/parameters/debug, e.g. |
| echo 0 > /sys/module/gigaset/parameters/debug |
| switches off debugging output completely, |
| echo 0x10a020 > /sys/module/gigaset/parameters/debug |
| enables the standard set of debugging output messages. These values are |
| bit patterns where every bit controls a certain type of debugging output. |
| See the constants DEBUG_* in the source file gigaset.h for details. |
| |
| The initial value can be set using the debug parameter when loading the |
| module "gigaset", e.g. by adding a line |
| options gigaset debug=0 |
| to /etc/modprobe.conf, ... |
| |
| Generated debugging information can be found |
| - as output of the command |
| dmesg |
| - in system log files written by your syslog daemon, usually |
| in /var/log/, e.g. /var/log/messages. |
| |
| 3.3. Reporting problems and bugs |
| --------------------------- |
| If you can't solve problems with the driver on your own, feel free to |
| use one of the forums, bug trackers, or mailing lists on |
| http://sourceforge.net/projects/gigaset307x |
| or write an electronic mail to the maintainers. |
| |
| Try to provide as much information as possible, such as |
| - distribution |
| - kernel version (uname -r) |
| - gcc version (gcc --version) |
| - hardware architecture (uname -m, ...) |
| - type and firmware version of your device (base and wireless module, |
| if any) |
| - output of "lsusb -v" (if using an USB device) |
| - error messages |
| - relevant system log messages (it would help if you activate debug |
| output as described in 3.2.) |
| |
| For help with general configuration problems not specific to our driver, |
| such as isdn4linux and network configuration issues, please refer to the |
| appropriate forums and newsgroups. |
| |
| 3.4. Reporting problem solutions |
| --------------------------- |
| If you solved a problem with our drivers, wrote startup scripts for your |
| distribution, ... feel free to contact us (using one of the places |
| mentioned in 3.3.). We'd like to add scripts, hints, documentation |
| to the driver and/or the project web page. |
| |
| |
| 4. Links, other software |
| --------------------- |
| - Sourceforge project developing this driver and associated tools |
| http://sourceforge.net/projects/gigaset307x |
| - Yahoo! Group on the Siemens Gigaset family of devices |
| http://de.groups.yahoo.com/group/Siemens-Gigaset |
| - Siemens Gigaset/T-Sinus compatibility table |
| http://www.erbze.info/sinus_gigaset.htm |
| |
| |
| 5. Credits |
| ------- |
| Thanks to |
| |
| Karsten Keil |
| for his help with isdn4linux |
| Deti Fliegl |
| for his base driver code |
| Dennis Dietrich |
| for his kernel 2.6 patches |
| Andreas Rummel |
| for his work and logs to get unimodem mode working |
| Andreas Degert |
| for his logs and patches to get cx 100 working |
| Dietrich Feist |
| for his generous donation of one M105 and two M101 cordless adapters |
| Christoph Schweers |
| for his generous donation of a M34 device |
| |
| and all the other people who sent logs and other information. |
| |
