Merge tag 'soc-arm-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The at91 power management code and the TI AM33 platform each get a few
updates for robustness, the other changes are just minor cleanups"
* tag 'soc-arm-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: versatile: clock: convert from round_rate() to determine_rate()
ARM: rockchip: remove REGULATOR conditional to PM
ARM: at91: pm: Remove 2.5V regulator
ARM: OMAP2+: clock: convert from round_rate() to determine_rate()
ARM: OMAP1: clock: convert from round_rate() to determine_rate()
ARM: mach-hpe: Rework support and directory structure
arm: omap2: use string choices helper
ARM: OMAP2+: pm33xx-core: ix device node reference leaks in amx3_idle_init
ARM: OMAP2+: use IS_ERR_OR_NULL() helper
ARM: AM33xx: Implement TI advisory 1.0.36 (EMU0/EMU1 pins state on reset)
ARM: at91: pm: save and restore ACR during PLL disable/enable
ARM: at91: pm: fix MCKx restore routine
ARM: at91: pm: fix .uhp_udp_mask specification for current SoCs
ARM: shmobile: rcar-gen2: Use SZ_256K definition
diff --git a/MAINTAINERS b/MAINTAINERS
index 62a1692..6d7b697 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2737,7 +2737,6 @@
F: Documentation/devicetree/bindings/timer/hpe,gxp-timer.yaml
F: Documentation/hwmon/gxp-fan-ctrl.rst
F: arch/arm/boot/dts/hpe/
-F: arch/arm/mach-hpe/
F: drivers/clocksource/timer-gxp.c
F: drivers/hwmon/gxp-fan-ctrl.c
F: drivers/i2c/busses/i2c-gxp.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3580570..f84aa52 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -393,8 +393,6 @@
source "arch/arm/mach-hisi/Kconfig"
-source "arch/arm/mach-hpe/Kconfig"
-
source "arch/arm/mach-imx/Kconfig"
source "arch/arm/mach-ixp4xx/Kconfig"
diff --git a/arch/arm/Kconfig.platforms b/arch/arm/Kconfig.platforms
index 845ab08..5c19c1f 100644
--- a/arch/arm/Kconfig.platforms
+++ b/arch/arm/Kconfig.platforms
@@ -87,6 +87,31 @@
help
Support for Alphascale ASM9260 based platform.
+menuconfig ARCH_HPE
+ bool "HPE SoC support"
+ depends on ARCH_MULTI_V7
+ help
+ This enables support for HPE ARM based BMC chips.
+
+if ARCH_HPE
+
+config ARCH_HPE_GXP
+ bool "HPE GXP SoC"
+ depends on ARCH_MULTI_V7
+ select ARM_VIC
+ select GENERIC_IRQ_CHIP
+ select CLKSRC_MMIO
+ help
+ HPE GXP is the name of the HPE Soc. This SoC is used to implement many
+ BMC features at HPE. It supports ARMv7 architecture based on the Cortex
+ A9 core. It is capable of using an AXI bus to which a memory controller
+ is attached. It has multiple SPI interfaces to connect boot flash and
+ BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It
+ has multiple i2c engines to drive connectivity with a host
+ infrastructure.
+
+endif
+
menuconfig ARCH_MOXART
bool "MOXA ART SoC"
depends on ARCH_MULTI_V4
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index e31e95f..b7de4b6 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -189,7 +189,6 @@
machine-$(CONFIG_ARCH_GEMINI) += gemini
machine-$(CONFIG_ARCH_HIGHBANK) += highbank
machine-$(CONFIG_ARCH_HISI) += hisi
-machine-$(CONFIG_ARCH_HPE) += hpe
machine-$(CONFIG_ARCH_IXP4XX) += ixp4xx
machine-$(CONFIG_ARCH_KEYSTONE) += keystone
machine-$(CONFIG_ARCH_LPC18XX) += lpc18xx
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 3aa2003..35058b9 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -1364,7 +1364,7 @@ static const struct pmc_info pmc_infos[] __initconst = {
.version = AT91_PMC_V1,
},
{
- .uhp_udp_mask = AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP,
+ .uhp_udp_mask = AT91SAM926x_PMC_UHP,
.mckr = 0x28,
.version = AT91_PMC_V2,
},
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index e23b868..2e639f9 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -87,29 +87,6 @@
.endm
-/**
- * Set state for 2.5V low power regulator
- * @ena: 0 - disable regulator
- * 1 - enable regulator
- *
- * Side effects: overwrites r7, r8, r9, r10
- */
- .macro at91_2_5V_reg_set_low_power ena
-#ifdef CONFIG_SOC_SAMA7
- ldr r7, .sfrbu
- mov r8, #\ena
- ldr r9, [r7, #AT91_SFRBU_25LDOCR]
- orr r9, r9, #AT91_SFRBU_25LDOCR_LP
- cmp r8, #1
- beq lp_done_\ena
- bic r9, r9, #AT91_SFRBU_25LDOCR_LP
-lp_done_\ena:
- ldr r10, =AT91_SFRBU_25LDOCR_LDOANAKEY
- orr r9, r9, r10
- str r9, [r7, #AT91_SFRBU_25LDOCR]
-#endif
- .endm
-
.macro at91_backup_set_lpm reg
#ifdef CONFIG_SOC_SAMA7
orr \reg, \reg, #0x200000
@@ -689,6 +666,10 @@
bic tmp2, tmp2, #AT91_PMC_PLL_UPDT_ID
str tmp2, [pmc, #AT91_PMC_PLL_UPDT]
+ /* save acr */
+ ldr tmp2, [pmc, #AT91_PMC_PLL_ACR]
+ str tmp2, .saved_acr
+
/* save div. */
mov tmp1, #0
ldr tmp2, [pmc, #AT91_PMC_PLL_CTRL0]
@@ -758,7 +739,7 @@
str tmp1, [pmc, #AT91_PMC_PLL_UPDT]
/* step 2. */
- ldr tmp1, =AT91_PMC_PLL_ACR_DEFAULT_PLLA
+ ldr tmp1, .saved_acr
str tmp1, [pmc, #AT91_PMC_PLL_ACR]
/* step 3. */
@@ -904,7 +885,7 @@
/**
* at91_mckx_ps_restore: restore MCKx settings
*
- * Side effects: overwrites tmp1, tmp2
+ * Side effects: overwrites tmp1, tmp2 and tmp3
*/
.macro at91_mckx_ps_restore
#ifdef CONFIG_SOC_SAMA7
@@ -980,7 +961,7 @@
bic tmp3, tmp3, #AT91_PMC_MCR_V2_ID_MSK
orr tmp3, tmp3, tmp1
orr tmp3, tmp3, #AT91_PMC_MCR_V2_CMD
- str tmp2, [pmc, #AT91_PMC_MCR_V2]
+ str tmp3, [pmc, #AT91_PMC_MCR_V2]
wait_mckrdy tmp1
@@ -1019,9 +1000,6 @@
at91_plla_disable
- /* Enable low power mode for 2.5V regulator. */
- at91_2_5V_reg_set_low_power 1
-
ldr tmp3, .pm_mode
cmp tmp3, #AT91_PM_ULP1
beq ulp1_mode
@@ -1034,9 +1012,6 @@
b ulp_exit
ulp_exit:
- /* Disable low power mode for 2.5V regulator. */
- at91_2_5V_reg_set_low_power 0
-
ldr pmc, .pmc_base
at91_plla_enable
@@ -1207,6 +1182,8 @@
#endif
.saved_mckr:
.word 0
+.saved_acr:
+ .word 0
.saved_pllar:
.word 0
.saved_sam9_lpr:
diff --git a/arch/arm/mach-hpe/Kconfig b/arch/arm/mach-hpe/Kconfig
deleted file mode 100644
index 3372bbf..0000000
--- a/arch/arm/mach-hpe/Kconfig
+++ /dev/null
@@ -1,23 +0,0 @@
-menuconfig ARCH_HPE
- bool "HPE SoC support"
- depends on ARCH_MULTI_V7
- help
- This enables support for HPE ARM based BMC chips.
-if ARCH_HPE
-
-config ARCH_HPE_GXP
- bool "HPE GXP SoC"
- depends on ARCH_MULTI_V7
- select ARM_VIC
- select GENERIC_IRQ_CHIP
- select CLKSRC_MMIO
- help
- HPE GXP is the name of the HPE Soc. This SoC is used to implement many
- BMC features at HPE. It supports ARMv7 architecture based on the Cortex
- A9 core. It is capable of using an AXI bus to which a memory controller
- is attached. It has multiple SPI interfaces to connect boot flash and
- BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It
- has multiple i2c engines to drive connectivity with a host
- infrastructure.
-
-endif
diff --git a/arch/arm/mach-hpe/Makefile b/arch/arm/mach-hpe/Makefile
deleted file mode 100644
index 8b0a912..0000000
--- a/arch/arm/mach-hpe/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-$(CONFIG_ARCH_HPE_GXP) += gxp.o
diff --git a/arch/arm/mach-hpe/gxp.c b/arch/arm/mach-hpe/gxp.c
deleted file mode 100644
index 581c8da..0000000
--- a/arch/arm/mach-hpe/gxp.c
+++ /dev/null
@@ -1,15 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/* Copyright (C) 2022 Hewlett-Packard Enterprise Development Company, L.P. */
-
-#include <asm/mach/arch.h>
-
-static const char * const gxp_board_dt_compat[] = {
- "hpe,gxp",
- NULL,
-};
-
-DT_MACHINE_START(GXP_DT, "HPE GXP")
- .dt_compat = gxp_board_dt_compat,
- .l2c_aux_val = 0,
- .l2c_aux_mask = ~0,
-MACHINE_END
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 83381e2..afc6404 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -705,14 +705,21 @@ static unsigned long omap1_clk_recalc_rate(struct clk_hw *hw, unsigned long p_ra
return clk->rate;
}
-static long omap1_clk_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *p_rate)
+static int omap1_clk_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
{
struct omap1_clk *clk = to_omap1_clk(hw);
- if (clk->round_rate != NULL)
- return clk->round_rate(clk, rate, p_rate);
+ if (clk->round_rate != NULL) {
+ req->rate = clk->round_rate(clk, req->rate,
+ &req->best_parent_rate);
- return omap1_clk_recalc_rate(hw, *p_rate);
+ return 0;
+ }
+
+ req->rate = omap1_clk_recalc_rate(hw, req->best_parent_rate);
+
+ return 0;
}
static int omap1_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long p_rate)
@@ -771,7 +778,7 @@ const struct clk_ops omap1_clk_gate_ops = {
const struct clk_ops omap1_clk_rate_ops = {
.recalc_rate = omap1_clk_recalc_rate,
- .round_rate = omap1_clk_round_rate,
+ .determine_rate = omap1_clk_determine_rate,
.set_rate = omap1_clk_set_rate,
.init = omap1_clk_init_op,
};
@@ -784,7 +791,7 @@ const struct clk_ops omap1_clk_full_ops = {
.disable_unused = omap1_clk_disable_unused,
#endif
.recalc_rate = omap1_clk_recalc_rate,
- .round_rate = omap1_clk_round_rate,
+ .determine_rate = omap1_clk_determine_rate,
.set_rate = omap1_clk_set_rate,
.init = omap1_clk_init_op,
};
diff --git a/arch/arm/mach-omap2/am33xx-restart.c b/arch/arm/mach-omap2/am33xx-restart.c
index fcf3d55..3cdf223 100644
--- a/arch/arm/mach-omap2/am33xx-restart.c
+++ b/arch/arm/mach-omap2/am33xx-restart.c
@@ -2,12 +2,46 @@
/*
* am33xx-restart.c - Code common to all AM33xx machines.
*/
+#include <dt-bindings/pinctrl/am33xx.h>
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/reboot.h>
#include "common.h"
+#include "control.h"
#include "prm.h"
+/*
+ * Advisory 1.0.36 EMU0 and EMU1: Terminals Must be Pulled High Before
+ * ICEPick Samples
+ *
+ * If EMU0/EMU1 pins have been used as GPIO outputs and actively driving low
+ * level, the device might not reboot in normal mode. We are in a bad position
+ * to override GPIO state here, so just switch the pins into EMU input mode
+ * (that's what reset will do anyway) and wait a bit, because the state will be
+ * latched 190 ns after reset.
+ */
+static void am33xx_advisory_1_0_36(void)
+{
+ u32 emu0 = omap_ctrl_readl(AM335X_PIN_EMU0);
+ u32 emu1 = omap_ctrl_readl(AM335X_PIN_EMU1);
+
+ /* If both pins are in EMU mode, nothing to do */
+ if (!(emu0 & 7) && !(emu1 & 7))
+ return;
+
+ /* Switch GPIO3_7/GPIO3_8 into EMU0/EMU1 modes respectively */
+ omap_ctrl_writel(emu0 & ~7, AM335X_PIN_EMU0);
+ omap_ctrl_writel(emu1 & ~7, AM335X_PIN_EMU1);
+
+ /*
+ * Give pull-ups time to load the pin/PCB trace capacity.
+ * 5 ms shall be enough to load 1 uF (would be huge capacity for these
+ * pins) with TI-recommended 4k7 external pull-ups.
+ */
+ mdelay(5);
+}
+
/**
* am33xx_restart - trigger a software restart of the SoC
* @mode: the "reboot mode", see arch/arm/kernel/{setup,process}.c
@@ -18,6 +52,8 @@
*/
void am33xx_restart(enum reboot_mode mode, const char *cmd)
{
+ am33xx_advisory_1_0_36();
+
/* TODO: Handle cmd if necessary */
prm_reboot_mode = mode;
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index ff2a4a4..969265d 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -167,7 +167,7 @@ static int n8x0_mmc_set_power_menelaus(struct device *dev, int slot,
#ifdef CONFIG_MMC_DEBUG
dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
- power_on ? "on" : "off", vdd);
+ str_on_off(power_on), vdd);
#endif
if (slot == 0) {
if (!power_on)
diff --git a/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c b/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
index 011076a..96c5cdc 100644
--- a/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
+++ b/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
@@ -70,8 +70,8 @@ static unsigned long omap2_table_mpu_recalc(struct clk_hw *clk,
* Some might argue L3-DDR, others ARM, others IVA. This code is simple and
* just uses the ARM rates.
*/
-static long omap2_round_to_table_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *parent_rate)
+static int omap2_determine_rate_to_table(struct clk_hw *hw,
+ struct clk_rate_request *req)
{
const struct prcm_config *ptr;
long highest_rate;
@@ -87,10 +87,12 @@ static long omap2_round_to_table_rate(struct clk_hw *hw, unsigned long rate,
highest_rate = ptr->mpu_speed;
/* Can check only after xtal frequency check */
- if (ptr->mpu_speed <= rate)
+ if (ptr->mpu_speed <= req->rate)
break;
}
- return highest_rate;
+ req->rate = highest_rate;
+
+ return 0;
}
/* Sets basic clocks based on the specified rate */
@@ -215,7 +217,7 @@ static void omap2xxx_clkt_vps_late_init(void)
static const struct clk_ops virt_prcm_set_ops = {
.recalc_rate = &omap2_table_mpu_recalc,
.set_rate = &omap2_select_table_rate,
- .round_rate = &omap2_round_to_table_rate,
+ .determine_rate = &omap2_determine_rate_to_table,
};
/**
diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c
index c907478b..4abb86d 100644
--- a/arch/arm/mach-omap2/pm33xx-core.c
+++ b/arch/arm/mach-omap2/pm33xx-core.c
@@ -388,12 +388,15 @@ static int __init amx3_idle_init(struct device_node *cpu_node, int cpu)
if (!state_node)
break;
- if (!of_device_is_available(state_node))
+ if (!of_device_is_available(state_node)) {
+ of_node_put(state_node);
continue;
+ }
if (i == CPUIDLE_STATE_MAX) {
pr_warn("%s: cpuidle states reached max possible\n",
__func__);
+ of_node_put(state_node);
break;
}
@@ -403,6 +406,7 @@ static int __init amx3_idle_init(struct device_node *cpu_node, int cpu)
states[state_count].wfi_flags |= WFI_FLAG_WAKE_M3 |
WFI_FLAG_FLUSH_CACHE;
+ of_node_put(state_node);
state_count++;
}
diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c
index a478530..0225b98 100644
--- a/arch/arm/mach-omap2/powerdomain.c
+++ b/arch/arm/mach-omap2/powerdomain.c
@@ -1111,7 +1111,7 @@ int omap_set_pwrdm_state(struct powerdomain *pwrdm, u8 pwrst)
int curr_pwrst;
int ret = 0;
- if (!pwrdm || IS_ERR(pwrdm))
+ if (IS_ERR_OR_NULL(pwrdm))
return -EINVAL;
while (!(pwrdm->pwrsts & (1 << pwrst))) {
diff --git a/arch/arm/mach-omap2/voltage.c b/arch/arm/mach-omap2/voltage.c
index 49e8bc6..000c2bc 100644
--- a/arch/arm/mach-omap2/voltage.c
+++ b/arch/arm/mach-omap2/voltage.c
@@ -51,7 +51,7 @@ static LIST_HEAD(voltdm_list);
*/
unsigned long voltdm_get_voltage(struct voltagedomain *voltdm)
{
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return 0;
}
@@ -73,7 +73,7 @@ static int voltdm_scale(struct voltagedomain *voltdm,
int ret, i;
unsigned long volt = 0;
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return -EINVAL;
}
@@ -124,7 +124,7 @@ void voltdm_reset(struct voltagedomain *voltdm)
{
unsigned long target_volt;
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return;
}
@@ -154,7 +154,7 @@ void voltdm_reset(struct voltagedomain *voltdm)
void omap_voltage_get_volttable(struct voltagedomain *voltdm,
struct omap_volt_data **volt_data)
{
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return;
}
@@ -182,7 +182,7 @@ struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
{
int i;
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return ERR_PTR(-EINVAL);
}
@@ -216,7 +216,7 @@ struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
int omap_voltage_register_pmic(struct voltagedomain *voltdm,
struct omap_voltdm_pmic *pmic)
{
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return -EINVAL;
}
diff --git a/arch/arm/mach-omap2/vp.c b/arch/arm/mach-omap2/vp.c
index a709655..03c481c 100644
--- a/arch/arm/mach-omap2/vp.c
+++ b/arch/arm/mach-omap2/vp.c
@@ -199,7 +199,7 @@ void omap_vp_enable(struct voltagedomain *voltdm)
struct omap_vp_instance *vp;
u32 vpconfig, volt;
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return;
}
@@ -244,7 +244,7 @@ void omap_vp_disable(struct voltagedomain *voltdm)
u32 vpconfig;
int timeout;
- if (!voltdm || IS_ERR(voltdm)) {
+ if (IS_ERR_OR_NULL(voltdm)) {
pr_warn("%s: VDD specified does not exist!\n", __func__);
return;
}
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig
index b7855cc..c90193d 100644
--- a/arch/arm/mach-rockchip/Kconfig
+++ b/arch/arm/mach-rockchip/Kconfig
@@ -13,7 +13,7 @@
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
select DW_APB_TIMER_OF
- select REGULATOR if PM
+ select REGULATOR
select ROCKCHIP_TIMER
select ARM_GLOBAL_TIMER
select CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK
diff --git a/arch/arm/mach-shmobile/pm-rcar-gen2.c b/arch/arm/mach-shmobile/pm-rcar-gen2.c
index 907a4f8..46654d1 100644
--- a/arch/arm/mach-shmobile/pm-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/pm-rcar-gen2.c
@@ -81,7 +81,7 @@ void __init rcar_gen2_pm_init(void)
map:
/* RAM for jump stub, because BAR requires 256KB aligned address */
- if (res.start & (256 * 1024 - 1) ||
+ if (res.start & (SZ_256K - 1) ||
resource_size(&res) < shmobile_boot_size) {
pr_err("Invalid smp-sram region\n");
return;
diff --git a/arch/arm/mach-versatile/spc.c b/arch/arm/mach-versatile/spc.c
index 7900927..812db32 100644
--- a/arch/arm/mach-versatile/spc.c
+++ b/arch/arm/mach-versatile/spc.c
@@ -497,12 +497,13 @@ static unsigned long spc_recalc_rate(struct clk_hw *hw,
return freq * 1000;
}
-static long spc_round_rate(struct clk_hw *hw, unsigned long drate,
- unsigned long *parent_rate)
+static int spc_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
{
struct clk_spc *spc = to_clk_spc(hw);
- return ve_spc_round_performance(spc->cluster, drate);
+ req->rate = ve_spc_round_performance(spc->cluster, req->rate);
+
+ return 0;
}
static int spc_set_rate(struct clk_hw *hw, unsigned long rate,
@@ -515,7 +516,7 @@ static int spc_set_rate(struct clk_hw *hw, unsigned long rate,
static struct clk_ops clk_spc_ops = {
.recalc_rate = spc_recalc_rate,
- .round_rate = spc_round_rate,
+ .determine_rate = spc_determine_rate,
.set_rate = spc_set_rate,
};
diff --git a/include/soc/at91/sama7-sfrbu.h b/include/soc/at91/sama7-sfrbu.h
index 76b7408..8cee48d 100644
--- a/include/soc/at91/sama7-sfrbu.h
+++ b/include/soc/at91/sama7-sfrbu.h
@@ -18,13 +18,6 @@
#define AT91_SFRBU_PSWBU_SOFTSWITCH (1 << 1) /* Power switch BU source selection */
#define AT91_SFRBU_PSWBU_CTRL (1 << 0) /* Power switch BU control */
-#define AT91_SFRBU_25LDOCR (0x0C) /* SFRBU 2.5V LDO Control Register */
-#define AT91_SFRBU_25LDOCR_LDOANAKEY (0x3B6E18 << 8) /* Specific value mandatory to allow writing of other register bits. */
-#define AT91_SFRBU_25LDOCR_STATE (1 << 3) /* LDOANA Switch On/Off Control */
-#define AT91_SFRBU_25LDOCR_LP (1 << 2) /* LDOANA Low-Power Mode Control */
-#define AT91_SFRBU_PD_VALUE_MSK (0x3)
-#define AT91_SFRBU_25LDOCR_PD_VALUE(v) ((v) & AT91_SFRBU_PD_VALUE_MSK) /* LDOANA Pull-down value */
-
#define AT91_FRBU_DDRPWR (0x10) /* SFRBU DDR Power Control Register */
#define AT91_FRBU_DDRPWR_STATE (1 << 0) /* DDR Power Mode State */
