blob: 415ccdd7442d4dc849e2fad4949e5e5221242086 [file] [log] [blame]
* Universal Flash Storage (UFS) Host Controller
UFSHC nodes are defined to describe on-chip UFS host controllers.
Each UFS controller instance should have its own node.
Required properties:
- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0"
For Qualcomm SoCs must contain, as below, an
SoC-specific compatible along with "qcom,ufshc" and
the appropriate jedec string:
"qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
"qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
"qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
"qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
"qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- interrupts : <interrupt mapping for UFS host controller IRQ>
- reg : <registers mapping>
Optional properties:
- phys : phandle to UFS PHY node
- phy-names : the string "ufsphy" when is found in a node, along
with "phys" attribute, provides phandle to UFS PHY node
- vdd-hba-supply : phandle to UFS host controller supply regulator node
- vcc-supply : phandle to VCC supply regulator node
- vccq-supply : phandle to VCCQ supply regulator node
- vccq2-supply : phandle to VCCQ2 supply regulator node
- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V
or 2.7-3.6V. This boolean property when set, specifies
to use low voltage range of 1.7-1.95V. Note for external
UFS cards this property is invalid and valid VCC range is
always 2.7-3.6V.
- vcc-max-microamp : specifies max. load that can be drawn from vcc supply
- vccq-max-microamp : specifies max. load that can be drawn from vccq supply
- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply
- clocks : List of phandle and clock specifier pairs
- clock-names : List of clock input name strings sorted in the same
order as the clocks property.
"ref_clk" indicates reference clock frequency.
UFS host supplies reference clock to UFS device and UFS device
specification allows host to provide one of the 4 frequencies (19.2 MHz,
26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is
parsed and used to update the reference clock setting in device.
Defaults to 26 MHz(as per specification) if not specified by host.
- freq-table-hz : Array of <min max> operating frequencies stored in the same
order as the clocks property. If this property is not
defined or a value in the array is "0" then it is assumed
that the frequency is set by the parent clock or a
fixed rate clock source.
-lanes-per-direction : number of lanes available per direction - either 1 or 2.
Note that it is assume same number of lanes is used both
directions at once. If not specified, default is 2 lanes per direction.
- #reset-cells : Must be <1> for Qualcomm UFS controllers that expose
PHY reset from the UFS controller.
- resets : reset node register
- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP.
- reset-gpios : A phandle and gpio specifier denoting the GPIO connected
to the RESET pin of the UFS memory device.
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
ufshc@fc598000 {
compatible = "jedec,ufs-1.1";
reg = <0xfc598000 0x800>;
interrupts = <0 28 0>;
vdd-hba-supply = <&xxx_reg0>;
vcc-supply = <&xxx_reg1>;
vccq-supply = <&xxx_reg2>;
vccq2-supply = <&xxx_reg3>;
vcc-max-microamp = 500000;
vccq-max-microamp = 200000;
vccq2-max-microamp = 200000;
clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>;
clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk";
freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
resets = <&reset 0 1>;
reset-names = "rst";
phys = <&ufsphy1>;
phy-names = "ufsphy";
#reset-cells = <1>;