blob: f2dc850010f10c1e73b48a2897e31ae0aeb6eb7b [file] [log] [blame]
/*
* Copyright (c) 2017 MediaTek Inc.
* Author: Ming Huang <ming.huang@mediatek.com>
* Sean Wang <sean.wang@mediatek.com>
*
* SPDX-License-Identifier: (GPL-2.0 OR MIT)
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "mt7622.dtsi"
#include "mt6380.dtsi"
/ {
model = "MediaTek MT7622 RFB1 board";
compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
};
cpus {
cpu@0 {
proc-supply = <&mt6380_vcpu_reg>;
sram-supply = <&mt6380_vm_reg>;
};
cpu@1 {
proc-supply = <&mt6380_vcpu_reg>;
sram-supply = <&mt6380_vm_reg>;
};
};
gpio-keys {
compatible = "gpio-keys";
poll-interval = <100>;
factory {
label = "factory";
linux,code = <BTN_0>;
gpios = <&pio 0 0>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&pio 102 0>;
};
};
memory {
reg = <0 0x40000000 0 0x20000000>;
};
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "fixed-5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
regulator-always-on;
};
};
&bch {
status = "disabled";
};
&btif {
status = "okay";
};
&cir {
pinctrl-names = "default";
pinctrl-0 = <&irrx_pins>;
status = "okay";
};
&eth {
pinctrl-names = "default";
pinctrl-0 = <&eth_pins>;
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
switch@0 {
compatible = "mediatek,mt7531";
reg = <0>;
reset-gpios = <&pio 54 0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan0";
};
port@1 {
reg = <1>;
label = "lan1";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan3";
};
port@4 {
reg = <4>;
label = "wan";
};
port@6 {
reg = <6>;
label = "cpu";
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&emmc_pins_default>;
pinctrl-1 = <&emmc_pins_uhs>;
status = "okay";
bus-width = <8>;
max-frequency = <50000000>;
cap-mmc-highspeed;
mmc-hs200-1_8v;
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&reg_1p8v>;
assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
non-removable;
};
&mmc1 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&sd0_pins_default>;
pinctrl-1 = <&sd0_pins_uhs>;
status = "okay";
bus-width = <4>;
max-frequency = <50000000>;
cap-sd-highspeed;
r_smpl = <1>;
cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&reg_3p3v>;
assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
};
&nandc {
pinctrl-names = "default";
pinctrl-0 = <&parallel_nand_pins>;
status = "disabled";
};
&nor_flash {
pinctrl-names = "default";
pinctrl-0 = <&spi_nor_pins>;
status = "disabled";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
};
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pcie0_pins>;
status = "okay";
pcie@0,0 {
status = "okay";
};
};
&pio {
/* eMMC is shared pin with parallel NAND */
emmc_pins_default: emmc-pins-default {
mux {
function = "emmc", "emmc_rst";
groups = "emmc";
};
/* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
* "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
* DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
*/
conf-cmd-dat {
pins = "NDL0", "NDL1", "NDL2",
"NDL3", "NDL4", "NDL5",
"NDL6", "NDL7", "NRB";
input-enable;
bias-pull-up;
};
conf-clk {
pins = "NCLE";
bias-pull-down;
};
};
emmc_pins_uhs: emmc-pins-uhs {
mux {
function = "emmc";
groups = "emmc";
};
conf-cmd-dat {
pins = "NDL0", "NDL1", "NDL2",
"NDL3", "NDL4", "NDL5",
"NDL6", "NDL7", "NRB";
input-enable;
drive-strength = <4>;
bias-pull-up;
};
conf-clk {
pins = "NCLE";
drive-strength = <4>;
bias-pull-down;
};
};
eth_pins: eth-pins {
mux {
function = "eth";
groups = "mdc_mdio", "rgmii_via_gmac2";
};
};
i2c1_pins: i2c1-pins {
mux {
function = "i2c";
groups = "i2c1_0";
};
};
i2c2_pins: i2c2-pins {
mux {
function = "i2c";
groups = "i2c2_0";
};
};
i2s1_pins: i2s1-pins {
mux {
function = "i2s";
groups = "i2s_out_mclk_bclk_ws",
"i2s1_in_data",
"i2s1_out_data";
};
conf {
pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
"I2S_WS", "I2S_MCLK";
drive-strength = <12>;
bias-pull-down;
};
};
irrx_pins: irrx-pins {
mux {
function = "ir";
groups = "ir_1_rx";
};
};
irtx_pins: irtx-pins {
mux {
function = "ir";
groups = "ir_1_tx";
};
};
/* Parallel nand is shared pin with eMMC */
parallel_nand_pins: parallel-nand-pins {
mux {
function = "flash";
groups = "par_nand";
};
};
pcie0_pins: pcie0-pins {
mux {
function = "pcie";
groups = "pcie0_pad_perst",
"pcie0_1_waken",
"pcie0_1_clkreq";
};
};
pcie1_pins: pcie1-pins {
mux {
function = "pcie";
groups = "pcie1_pad_perst",
"pcie1_0_waken",
"pcie1_0_clkreq";
};
};
pmic_bus_pins: pmic-bus-pins {
mux {
function = "pmic";
groups = "pmic_bus";
};
};
pwm7_pins: pwm1-2-pins {
mux {
function = "pwm";
groups = "pwm_ch7_2";
};
};
wled_pins: wled-pins {
mux {
function = "led";
groups = "wled";
};
};
sd0_pins_default: sd0-pins-default {
mux {
function = "sd";
groups = "sd_0";
};
/* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
* "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
* DAT2, DAT3, CMD, CLK for SD respectively.
*/
conf-cmd-data {
pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
"I2S2_IN","I2S4_OUT";
input-enable;
drive-strength = <8>;
bias-pull-up;
};
conf-clk {
pins = "I2S3_OUT";
drive-strength = <12>;
bias-pull-down;
};
conf-cd {
pins = "TXD3";
bias-pull-up;
};
};
sd0_pins_uhs: sd0-pins-uhs {
mux {
function = "sd";
groups = "sd_0";
};
conf-cmd-data {
pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
"I2S2_IN","I2S4_OUT";
input-enable;
bias-pull-up;
};
conf-clk {
pins = "I2S3_OUT";
bias-pull-down;
};
};
/* Serial NAND is shared pin with SPI-NOR */
serial_nand_pins: serial-nand-pins {
mux {
function = "flash";
groups = "snfi";
};
};
spic0_pins: spic0-pins {
mux {
function = "spi";
groups = "spic0_0";
};
};
spic1_pins: spic1-pins {
mux {
function = "spi";
groups = "spic1_0";
};
};
/* SPI-NOR is shared pin with serial NAND */
spi_nor_pins: spi-nor-pins {
mux {
function = "flash";
groups = "spi_nor";
};
};
/* serial NAND is shared pin with SPI-NOR */
serial_nand_pins: serial-nand-pins {
mux {
function = "flash";
groups = "snfi";
};
};
uart0_pins: uart0-pins {
mux {
function = "uart";
groups = "uart0_0_tx_rx" ;
};
};
uart2_pins: uart2-pins {
mux {
function = "uart";
groups = "uart2_1_tx_rx" ;
};
};
watchdog_pins: watchdog-pins {
mux {
function = "watchdog";
groups = "watchdog";
};
};
wmac_pins: wmac-pins {
mux {
function = "antsel";
groups = "antsel0", "antsel1", "antsel2", "antsel3",
"antsel4", "antsel5", "antsel6", "antsel7",
"antsel8", "antsel9", "antsel12", "antsel13",
"antsel14", "antsel15", "antsel16", "antsel17";
};
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm7_pins>;
status = "okay";
};
&pwrap {
pinctrl-names = "default";
pinctrl-0 = <&pmic_bus_pins>;
status = "okay";
};
&sata {
status = "okay";
};
&sata_phy {
status = "okay";
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spic0_pins>;
status = "okay";
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spic1_pins>;
status = "okay";
};
&ssusb {
vusb33-supply = <&reg_3p3v>;
vbus-supply = <&reg_5v>;
status = "okay";
};
&u3phy {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "okay";
};
&watchdog {
pinctrl-names = "default";
pinctrl-0 = <&watchdog_pins>;
status = "okay";
};
&wmac {
pinctrl-names = "default";
pinctrl-0 = <&wmac_pins>;
status = "okay";
};