| This file provides information on the module parameters of many of |
| the Linux watchdog drivers. Watchdog driver parameter specs should |
| be listed here unless the driver has its own driver-specific information |
| file. |
| |
| |
| See Documentation/kernel-parameters.txt for information on |
| providing kernel parameters for builtin drivers versus loadable |
| modules. |
| |
| |
| ------------------------------------------------- |
| acquirewdt: |
| wdt_stop: Acquire WDT 'stop' io port (default 0x43) |
| wdt_start: Acquire WDT 'start' io port (default 0x443) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| advantechwdt: |
| wdt_stop: Advantech WDT 'stop' io port (default 0x443) |
| wdt_start: Advantech WDT 'start' io port (default 0x443) |
| timeout: Watchdog timeout in seconds. 1<= timeout <=63, default=60. |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| alim1535_wdt: |
| timeout: Watchdog timeout in seconds. (0 < timeout < 18000, default=60 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| alim7101_wdt: |
| timeout: Watchdog timeout in seconds. (1<=timeout<=3600, default=30 |
| use_gpio: Use the gpio watchdog (required by old cobalt boards). |
| default=0/off/no |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| ar7_wdt: |
| margin: Watchdog margin in seconds (default=60) |
| nowayout: Disable watchdog shutdown on close |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| at32ap700x_wdt: |
| timeout: Timeout value. Limited to be 1 or 2 seconds. (default=2) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| at91rm9200_wdt: |
| wdt_time: Watchdog time in seconds. (default=5) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| at91sam9_wdt: |
| heartbeat: Watchdog heartbeats in seconds. (default = 15) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| bcm47xx_wdt: |
| wdt_time: Watchdog time in seconds. (default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| bfin_wdt: |
| timeout: Watchdog timeout in seconds. (1<=timeout<=((2^32)/SCLK), default=20) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| coh901327_wdt: |
| margin: Watchdog margin in seconds (default 60s) |
| ------------------------------------------------- |
| cpu5wdt: |
| port: base address of watchdog card, default is 0x91 |
| verbose: be verbose, default is 0 (no) |
| ticks: count down ticks, default is 10000 |
| ------------------------------------------------- |
| cpwd: |
| wd0_timeout: Default watchdog0 timeout in 1/10secs |
| wd1_timeout: Default watchdog1 timeout in 1/10secs |
| wd2_timeout: Default watchdog2 timeout in 1/10secs |
| ------------------------------------------------- |
| da9052wdt: |
| timeout: Watchdog timeout in seconds. 2<= timeout <=131, default=2.048s |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| davinci_wdt: |
| heartbeat: Watchdog heartbeat period in seconds from 1 to 600, default 60 |
| ------------------------------------------------- |
| ep93xx_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| timeout: Watchdog timeout in seconds. (1<=timeout<=3600, default=TBD) |
| ------------------------------------------------- |
| eurotechwdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| io: Eurotech WDT io port (default=0x3f0) |
| irq: Eurotech WDT irq (default=10) |
| ev: Eurotech WDT event type (default is `int') |
| ------------------------------------------------- |
| gef_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| geodewdt: |
| timeout: Watchdog timeout in seconds. 1<= timeout <=131, default=60. |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| i6300esb: |
| heartbeat: Watchdog heartbeat in seconds. (1<heartbeat<2046, default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| iTCO_wdt: |
| heartbeat: Watchdog heartbeat in seconds. |
| (2<heartbeat<39 (TCO v1) or 613 (TCO v2), default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| iTCO_vendor_support: |
| vendorsupport: iTCO vendor specific support mode, default=0 (none), |
| 1=SuperMicro Pent3, 2=SuperMicro Pent4+, 911=Broken SMI BIOS |
| ------------------------------------------------- |
| ib700wdt: |
| timeout: Watchdog timeout in seconds. 0<= timeout <=30, default=30. |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| ibmasr: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| imx2_wdt: |
| timeout: Watchdog timeout in seconds (default 60 s) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| indydog: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| iop_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| it8712f_wdt: |
| margin: Watchdog margin in seconds (default 60) |
| nowayout: Disable watchdog shutdown on close |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| it87_wdt: |
| nogameport: Forbid the activation of game port, default=0 |
| exclusive: Watchdog exclusive device open, default=1 |
| timeout: Watchdog timeout in seconds, default=60 |
| testmode: Watchdog test mode (1 = no reboot), default=0 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| ixp2000_wdt: |
| heartbeat: Watchdog heartbeat in seconds (default 60s) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| ixp4xx_wdt: |
| heartbeat: Watchdog heartbeat in seconds (default 60s) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| ks8695_wdt: |
| wdt_time: Watchdog time in seconds. (default=5) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| machzwd: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| action: after watchdog resets, generate: |
| 0 = RESET(*) 1 = SMI 2 = NMI 3 = SCI |
| ------------------------------------------------- |
| max63xx_wdt: |
| heartbeat: Watchdog heartbeat period in seconds from 1 to 60, default 60 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| nodelay: Force selection of a timeout setting without initial delay |
| (max6373/74 only, default=0) |
| ------------------------------------------------- |
| mixcomwd: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| mpc8xxx_wdt: |
| timeout: Watchdog timeout in ticks. (0<timeout<65536, default=65535) |
| reset: Watchdog Interrupt/Reset Mode. 0 = interrupt, 1 = reset |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| mpcore_wdt: |
| mpcore_margin: MPcore timer margin in seconds. |
| (0 < mpcore_margin < 65536, default=60) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| mpcore_noboot: MPcore watchdog action, set to 1 to ignore reboots, |
| 0 to reboot (default=0 |
| ------------------------------------------------- |
| mv64x60_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| nuc900_wdt: |
| heartbeat: Watchdog heartbeats in seconds. |
| (default = 15) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| omap_wdt: |
| timer_margin: initial watchdog timeout (in seconds) |
| ------------------------------------------------- |
| orion_wdt: |
| heartbeat: Initial watchdog heartbeat in seconds |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| pc87413_wdt: |
| io: pc87413 WDT I/O port (default: io). |
| timeout: Watchdog timeout in minutes (default=timeout). |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| pika_wdt: |
| heartbeat: Watchdog heartbeats in seconds. (default = 15) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| pnx4008_wdt: |
| heartbeat: Watchdog heartbeat period in seconds from 1 to 60, default 19 |
| nowayout: Set to 1 to keep watchdog running after device release |
| ------------------------------------------------- |
| pnx833x_wdt: |
| timeout: Watchdog timeout in Mhz. (68Mhz clock), default=2040000000 (30 seconds) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| start_enabled: Watchdog is started on module insertion (default=1) |
| ------------------------------------------------- |
| rc32434_wdt: |
| timeout: Watchdog timeout value, in seconds (default=20) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| riowd: |
| riowd_timeout: Watchdog timeout in minutes (default=1) |
| ------------------------------------------------- |
| s3c2410_wdt: |
| tmr_margin: Watchdog tmr_margin in seconds. (default=15) |
| tmr_atboot: Watchdog is started at boot time if set to 1, default=0 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| soft_noboot: Watchdog action, set to 1 to ignore reboots, 0 to reboot |
| debug: Watchdog debug, set to >1 for debug, (default 0) |
| ------------------------------------------------- |
| sa1100_wdt: |
| margin: Watchdog margin in seconds (default 60s) |
| ------------------------------------------------- |
| sb_wdog: |
| timeout: Watchdog timeout in microseconds (max/default 8388607 or 8.3ish secs) |
| ------------------------------------------------- |
| sbc60xxwdt: |
| wdt_stop: SBC60xx WDT 'stop' io port (default 0x45) |
| wdt_start: SBC60xx WDT 'start' io port (default 0x443) |
| timeout: Watchdog timeout in seconds. (1<=timeout<=3600, default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| sbc7240_wdt: |
| timeout: Watchdog timeout in seconds. (1<=timeout<=255, default=30) |
| nowayout: Disable watchdog when closing device file |
| ------------------------------------------------- |
| sbc8360: |
| timeout: Index into timeout table (0-63) (default=27 (60s)) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| sbc_epx_c3: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| sbc_fitpc2_wdt: |
| margin: Watchdog margin in seconds (default 60s) |
| nowayout: Watchdog cannot be stopped once started |
| ------------------------------------------------- |
| sc1200wdt: |
| isapnp: When set to 0 driver ISA PnP support will be disabled (default=1) |
| io: io port |
| timeout: range is 0-255 minutes, default is 1 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| sc520_wdt: |
| timeout: Watchdog timeout in seconds. (1 <= timeout <= 3600, default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| sch311x_wdt: |
| force_id: Override the detected device ID |
| therm_trip: Should a ThermTrip trigger the reset generator |
| timeout: Watchdog timeout in seconds. 1<= timeout <=15300, default=60 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| scx200_wdt: |
| margin: Watchdog margin in seconds |
| nowayout: Disable watchdog shutdown on close |
| ------------------------------------------------- |
| shwdt: |
| clock_division_ratio: Clock division ratio. Valid ranges are from 0x5 (1.31ms) |
| to 0x7 (5.25ms). (default=7) |
| heartbeat: Watchdog heartbeat in seconds. (1 <= heartbeat <= 3600, default=30 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| smsc37b787_wdt: |
| timeout: range is 1-255 units, default is 60 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| softdog: |
| soft_margin: Watchdog soft_margin in seconds. |
| (0 < soft_margin < 65536, default=60) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| soft_noboot: Softdog action, set to 1 to ignore reboots, 0 to reboot |
| (default=0) |
| ------------------------------------------------- |
| stmp3xxx_wdt: |
| heartbeat: Watchdog heartbeat period in seconds from 1 to 4194304, default 19 |
| ------------------------------------------------- |
| ts72xx_wdt: |
| timeout: Watchdog timeout in seconds. (1 <= timeout <= 8, default=8) |
| nowayout: Disable watchdog shutdown on close |
| ------------------------------------------------- |
| twl4030_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| txx9wdt: |
| timeout: Watchdog timeout in seconds. (0<timeout<N, default=60) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| w83627hf_wdt: |
| wdt_io: w83627hf/thf WDT io port (default 0x2E) |
| timeout: Watchdog timeout in seconds. 1 <= timeout <= 255, default=60. |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| w83697hf_wdt: |
| wdt_io: w83697hf/hg WDT io port (default 0x2e, 0 = autodetect) |
| timeout: Watchdog timeout in seconds. 1<= timeout <=255 (default=60) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| early_disable: Watchdog gets disabled at boot time (default=1) |
| ------------------------------------------------- |
| w83697ug_wdt: |
| wdt_io: w83697ug/uf WDT io port (default 0x2e) |
| timeout: Watchdog timeout in seconds. 1<= timeout <=255 (default=60) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| w83877f_wdt: |
| timeout: Watchdog timeout in seconds. (1<=timeout<=3600, default=30) |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| w83977f_wdt: |
| timeout: Watchdog timeout in seconds (15..7635), default=45) |
| testmode: Watchdog testmode (1 = no reboot), default=0 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| wafer5823wdt: |
| timeout: Watchdog timeout in seconds. 1 <= timeout <= 255, default=60. |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| wdt285: |
| soft_margin: Watchdog timeout in seconds (default=60) |
| ------------------------------------------------- |
| wdt977: |
| timeout: Watchdog timeout in seconds (60..15300, default=60) |
| testmode: Watchdog testmode (1 = no reboot), default=0 |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| wm831x_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
| wm8350_wdt: |
| nowayout: Watchdog cannot be stopped once started |
| (default=kernel config parameter) |
| ------------------------------------------------- |
