blob: 52ded516ea5caed2d85aff56000d2985af06daf8 [file] [log] [blame]
/*
* include/asm-arm/arch-ixp2000/platform.h
*
* Various bits of code used by platform-level code.
*
* Author: Deepak Saxena <dsaxena@plexity.net>
*
* Copyright 2004 (c) MontaVista Software, Inc.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#ifndef __ASSEMBLY__
/*
* The IXP2400 B0 silicon contains an erratum (#66) that causes writes
* to on-chip I/O register to not complete fully. What this means is
* that if you have a write to on-chip I/O followed by a back-to-back
* read or write, the first write will happen twice. OR...if it's
* not a back-to-back transaction, the read or write will generate
* incorrect data.
*
* The official work around for this is to set the on-chip I/O regions
* as XCB=101 and then force a read-back from the register.
*
*/
#if defined(CONFIG_ARCH_ENP2611) || defined(CONFIG_ARCH_IXDP2400) || defined(CONFIG_ARCH_IXDP2401)
#include <asm/system.h> /* Pickup local_irq_ functions */
static inline void ixp2000_reg_write(volatile unsigned long *reg, unsigned long val)
{
volatile unsigned long dummy;
unsigned long flags;
local_irq_save(flags);
*reg = val;
barrier();
dummy = *reg;
local_irq_restore(flags);
}
#else
#define ixp2000_reg_write(reg, val) (*reg = val)
#endif /* IXDP2400 || IXDP2401 */
/*
* Boards may multiplex different devices on the 2nd channel of
* the slowport interface that each need different configuration
* settings. For example, the IXDP2400 uses channel 2 on the interface
* to access the CPLD, the switch fabric card, and the media card. Each
* one needs a different mode so drivers must save/restore the mode
* before and after each operation.
*
* acquire_slowport(&your_config);
* ...
* do slowport operations
* ...
* release_slowport();
*
* Note that while you have the slowport, you are holding a spinlock,
* so your code should be written as if you explicitly acquired a lock.
*
* The configuration only affects device 2 on the slowport, so the
* MTD map driver does not acquire/release the slowport.
*/
struct slowport_cfg {
unsigned long CCR; /* Clock divide */
unsigned long WTC; /* Write Timing Control */
unsigned long RTC; /* Read Timing Control */
unsigned long PCR; /* Protocol Control Register */
unsigned long ADC; /* Address/Data Width Control */
};
void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
void ixp2000_release_slowport(struct slowport_cfg *);
/*
* IXP2400 A0/A1 and IXP2800 A0/A1/A2 have broken slowport that requires
* tweaking of addresses in the MTD driver.
*/
static inline unsigned ixp2000_has_broken_slowport(void)
{
unsigned long id = *IXP2000_PROD_ID;
unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
IXP2000_MIN_PROD_TYPE_MASK);
return (((id_prod ==
/* fixed in IXP2400-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2400)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
((id_prod ==
/* fixed in IXP2800-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2800)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
((id_prod ==
/* fixed in IXP2850-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2850)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)));
}
static inline unsigned int ixp2000_has_flash(void)
{
return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
}
static inline unsigned int ixp2000_is_pcimaster(void)
{
return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
}
void ixp2000_map_io(void);
void ixp2000_init_irq(void);
void ixp2000_init_time(unsigned long);
unsigned long ixp2000_gettimeoffset(void);
struct pci_sys_data;
u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
void ixp2000_pci_preinit(void);
int ixp2000_pci_setup(int, struct pci_sys_data*);
struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
/*
* Several of the IXP2000 systems have banked flash so we need to extend the
* flash_platform_data structure with some private pointers
*/
struct ixp2000_flash_data {
struct flash_platform_data *platform_data;
int nr_banks;
unsigned long (*bank_setup)(unsigned long);
};
struct ixp2000_i2c_pins {
unsigned long sda_pin;
unsigned long scl_pin;
};
#endif /* !__ASSEMBLY__ */