| /* | |
| * drivers/mtd/nand/diskonchip.c | |
| * | |
| * (C) 2003 Red Hat, Inc. | |
| * (C) 2004 Dan Brown <dan_brown@ieee.org> | |
| * (C) 2004 Kalev Lember <kalev@smartlink.ee> | |
| * | |
| * Author: David Woodhouse <dwmw2@infradead.org> | |
| * Additional Diskonchip 2000 and Millennium support by Dan Brown <dan_brown@ieee.org> | |
| * Diskonchip Millennium Plus support by Kalev Lember <kalev@smartlink.ee> | |
| * | |
| * Error correction code lifted from the old docecc code | |
| * Author: Fabrice Bellard (fabrice.bellard@netgem.com) | |
| * Copyright (C) 2000 Netgem S.A. | |
| * converted to the generic Reed-Solomon library by Thomas Gleixner <tglx@linutronix.de> | |
| * | |
| * Interface to generic NAND code for M-Systems DiskOnChip devices | |
| * | |
| * $Id: diskonchip.c,v 1.55 2005/11/07 11:14:30 gleixner Exp $ | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/sched.h> | |
| #include <linux/delay.h> | |
| #include <linux/rslib.h> | |
| #include <linux/moduleparam.h> | |
| #include <asm/io.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/nand.h> | |
| #include <linux/mtd/doc2000.h> | |
| #include <linux/mtd/compatmac.h> | |
| #include <linux/mtd/partitions.h> | |
| #include <linux/mtd/inftl.h> | |
| /* Where to look for the devices? */ | |
| #ifndef CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS | |
| #define CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS 0 | |
| #endif | |
| static unsigned long __initdata doc_locations[] = { | |
| #if defined (__alpha__) || defined(__i386__) || defined(__x86_64__) | |
| #ifdef CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH | |
| 0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000, | |
| 0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000, | |
| 0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000, | |
| 0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000, | |
| 0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000, | |
| #else /* CONFIG_MTD_DOCPROBE_HIGH */ | |
| 0xc8000, 0xca000, 0xcc000, 0xce000, | |
| 0xd0000, 0xd2000, 0xd4000, 0xd6000, | |
| 0xd8000, 0xda000, 0xdc000, 0xde000, | |
| 0xe0000, 0xe2000, 0xe4000, 0xe6000, | |
| 0xe8000, 0xea000, 0xec000, 0xee000, | |
| #endif /* CONFIG_MTD_DOCPROBE_HIGH */ | |
| #elif defined(__PPC__) | |
| 0xe4000000, | |
| #elif defined(CONFIG_MOMENCO_OCELOT_G) | |
| 0xff000000, | |
| #else | |
| #warning Unknown architecture for DiskOnChip. No default probe locations defined | |
| #endif | |
| 0xffffffff }; | |
| static struct mtd_info *doclist = NULL; | |
| struct doc_priv { | |
| void __iomem *virtadr; | |
| unsigned long physadr; | |
| u_char ChipID; | |
| u_char CDSNControl; | |
| int chips_per_floor; /* The number of chips detected on each floor */ | |
| int curfloor; | |
| int curchip; | |
| int mh0_page; | |
| int mh1_page; | |
| struct mtd_info *nextdoc; | |
| }; | |
| /* This is the syndrome computed by the HW ecc generator upon reading an empty | |
| page, one with all 0xff for data and stored ecc code. */ | |
| static u_char empty_read_syndrome[6] = { 0x26, 0xff, 0x6d, 0x47, 0x73, 0x7a }; | |
| /* This is the ecc value computed by the HW ecc generator upon writing an empty | |
| page, one with all 0xff for data. */ | |
| static u_char empty_write_ecc[6] = { 0x4b, 0x00, 0xe2, 0x0e, 0x93, 0xf7 }; | |
| #define INFTL_BBT_RESERVED_BLOCKS 4 | |
| #define DoC_is_MillenniumPlus(doc) ((doc)->ChipID == DOC_ChipID_DocMilPlus16 || (doc)->ChipID == DOC_ChipID_DocMilPlus32) | |
| #define DoC_is_Millennium(doc) ((doc)->ChipID == DOC_ChipID_DocMil) | |
| #define DoC_is_2000(doc) ((doc)->ChipID == DOC_ChipID_Doc2k) | |
| static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, | |
| unsigned int bitmask); | |
| static void doc200x_select_chip(struct mtd_info *mtd, int chip); | |
| static int debug = 0; | |
| module_param(debug, int, 0); | |
| static int try_dword = 1; | |
| module_param(try_dword, int, 0); | |
| static int no_ecc_failures = 0; | |
| module_param(no_ecc_failures, int, 0); | |
| static int no_autopart = 0; | |
| module_param(no_autopart, int, 0); | |
| static int show_firmware_partition = 0; | |
| module_param(show_firmware_partition, int, 0); | |
| #ifdef CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE | |
| static int inftl_bbt_write = 1; | |
| #else | |
| static int inftl_bbt_write = 0; | |
| #endif | |
| module_param(inftl_bbt_write, int, 0); | |
| static unsigned long doc_config_location = CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS; | |
| module_param(doc_config_location, ulong, 0); | |
| MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip"); | |
| /* Sector size for HW ECC */ | |
| #define SECTOR_SIZE 512 | |
| /* The sector bytes are packed into NB_DATA 10 bit words */ | |
| #define NB_DATA (((SECTOR_SIZE + 1) * 8 + 6) / 10) | |
| /* Number of roots */ | |
| #define NROOTS 4 | |
| /* First consective root */ | |
| #define FCR 510 | |
| /* Number of symbols */ | |
| #define NN 1023 | |
| /* the Reed Solomon control structure */ | |
| static struct rs_control *rs_decoder; | |
| /* | |
| * The HW decoder in the DoC ASIC's provides us a error syndrome, | |
| * which we must convert to a standard syndrom usable by the generic | |
| * Reed-Solomon library code. | |
| * | |
| * Fabrice Bellard figured this out in the old docecc code. I added | |
| * some comments, improved a minor bit and converted it to make use | |
| * of the generic Reed-Solomon libary. tglx | |
| */ | |
| static int doc_ecc_decode(struct rs_control *rs, uint8_t *data, uint8_t *ecc) | |
| { | |
| int i, j, nerr, errpos[8]; | |
| uint8_t parity; | |
| uint16_t ds[4], s[5], tmp, errval[8], syn[4]; | |
| /* Convert the ecc bytes into words */ | |
| ds[0] = ((ecc[4] & 0xff) >> 0) | ((ecc[5] & 0x03) << 8); | |
| ds[1] = ((ecc[5] & 0xfc) >> 2) | ((ecc[2] & 0x0f) << 6); | |
| ds[2] = ((ecc[2] & 0xf0) >> 4) | ((ecc[3] & 0x3f) << 4); | |
| ds[3] = ((ecc[3] & 0xc0) >> 6) | ((ecc[0] & 0xff) << 2); | |
| parity = ecc[1]; | |
| /* Initialize the syndrom buffer */ | |
| for (i = 0; i < NROOTS; i++) | |
| s[i] = ds[0]; | |
| /* | |
| * Evaluate | |
| * s[i] = ds[3]x^3 + ds[2]x^2 + ds[1]x^1 + ds[0] | |
| * where x = alpha^(FCR + i) | |
| */ | |
| for (j = 1; j < NROOTS; j++) { | |
| if (ds[j] == 0) | |
| continue; | |
| tmp = rs->index_of[ds[j]]; | |
| for (i = 0; i < NROOTS; i++) | |
| s[i] ^= rs->alpha_to[rs_modnn(rs, tmp + (FCR + i) * j)]; | |
| } | |
| /* Calc s[i] = s[i] / alpha^(v + i) */ | |
| for (i = 0; i < NROOTS; i++) { | |
| if (syn[i]) | |
| syn[i] = rs_modnn(rs, rs->index_of[s[i]] + (NN - FCR - i)); | |
| } | |
| /* Call the decoder library */ | |
| nerr = decode_rs16(rs, NULL, NULL, 1019, syn, 0, errpos, 0, errval); | |
| /* Incorrectable errors ? */ | |
| if (nerr < 0) | |
| return nerr; | |
| /* | |
| * Correct the errors. The bitpositions are a bit of magic, | |
| * but they are given by the design of the de/encoder circuit | |
| * in the DoC ASIC's. | |
| */ | |
| for (i = 0; i < nerr; i++) { | |
| int index, bitpos, pos = 1015 - errpos[i]; | |
| uint8_t val; | |
| if (pos >= NB_DATA && pos < 1019) | |
| continue; | |
| if (pos < NB_DATA) { | |
| /* extract bit position (MSB first) */ | |
| pos = 10 * (NB_DATA - 1 - pos) - 6; | |
| /* now correct the following 10 bits. At most two bytes | |
| can be modified since pos is even */ | |
| index = (pos >> 3) ^ 1; | |
| bitpos = pos & 7; | |
| if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { | |
| val = (uint8_t) (errval[i] >> (2 + bitpos)); | |
| parity ^= val; | |
| if (index < SECTOR_SIZE) | |
| data[index] ^= val; | |
| } | |
| index = ((pos >> 3) + 1) ^ 1; | |
| bitpos = (bitpos + 10) & 7; | |
| if (bitpos == 0) | |
| bitpos = 8; | |
| if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { | |
| val = (uint8_t) (errval[i] << (8 - bitpos)); | |
| parity ^= val; | |
| if (index < SECTOR_SIZE) | |
| data[index] ^= val; | |
| } | |
| } | |
| } | |
| /* If the parity is wrong, no rescue possible */ | |
| return parity ? -1 : nerr; | |
| } | |
| static void DoC_Delay(struct doc_priv *doc, unsigned short cycles) | |
| { | |
| volatile char dummy; | |
| int i; | |
| for (i = 0; i < cycles; i++) { | |
| if (DoC_is_Millennium(doc)) | |
| dummy = ReadDOC(doc->virtadr, NOP); | |
| else if (DoC_is_MillenniumPlus(doc)) | |
| dummy = ReadDOC(doc->virtadr, Mplus_NOP); | |
| else | |
| dummy = ReadDOC(doc->virtadr, DOCStatus); | |
| } | |
| } | |
| #define CDSN_CTRL_FR_B_MASK (CDSN_CTRL_FR_B0 | CDSN_CTRL_FR_B1) | |
| /* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */ | |
| static int _DoC_WaitReady(struct doc_priv *doc) | |
| { | |
| void __iomem *docptr = doc->virtadr; | |
| unsigned long timeo = jiffies + (HZ * 10); | |
| if (debug) | |
| printk("_DoC_WaitReady...\n"); | |
| /* Out-of-line routine to wait for chip response */ | |
| if (DoC_is_MillenniumPlus(doc)) { | |
| while ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { | |
| if (time_after(jiffies, timeo)) { | |
| printk("_DoC_WaitReady timed out.\n"); | |
| return -EIO; | |
| } | |
| udelay(1); | |
| cond_resched(); | |
| } | |
| } else { | |
| while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { | |
| if (time_after(jiffies, timeo)) { | |
| printk("_DoC_WaitReady timed out.\n"); | |
| return -EIO; | |
| } | |
| udelay(1); | |
| cond_resched(); | |
| } | |
| } | |
| return 0; | |
| } | |
| static inline int DoC_WaitReady(struct doc_priv *doc) | |
| { | |
| void __iomem *docptr = doc->virtadr; | |
| int ret = 0; | |
| if (DoC_is_MillenniumPlus(doc)) { | |
| DoC_Delay(doc, 4); | |
| if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) | |
| /* Call the out-of-line routine to wait */ | |
| ret = _DoC_WaitReady(doc); | |
| } else { | |
| DoC_Delay(doc, 4); | |
| if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) | |
| /* Call the out-of-line routine to wait */ | |
| ret = _DoC_WaitReady(doc); | |
| DoC_Delay(doc, 2); | |
| } | |
| if (debug) | |
| printk("DoC_WaitReady OK\n"); | |
| return ret; | |
| } | |
| static void doc2000_write_byte(struct mtd_info *mtd, u_char datum) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| if (debug) | |
| printk("write_byte %02x\n", datum); | |
| WriteDOC(datum, docptr, CDSNSlowIO); | |
| WriteDOC(datum, docptr, 2k_CDSN_IO); | |
| } | |
| static u_char doc2000_read_byte(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| u_char ret; | |
| ReadDOC(docptr, CDSNSlowIO); | |
| DoC_Delay(doc, 2); | |
| ret = ReadDOC(docptr, 2k_CDSN_IO); | |
| if (debug) | |
| printk("read_byte returns %02x\n", ret); | |
| return ret; | |
| } | |
| static void doc2000_writebuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("writebuf of %d bytes: ", len); | |
| for (i = 0; i < len; i++) { | |
| WriteDOC_(buf[i], docptr, DoC_2k_CDSN_IO + i); | |
| if (debug && i < 16) | |
| printk("%02x ", buf[i]); | |
| } | |
| if (debug) | |
| printk("\n"); | |
| } | |
| static void doc2000_readbuf(struct mtd_info *mtd, u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("readbuf of %d bytes: ", len); | |
| for (i = 0; i < len; i++) { | |
| buf[i] = ReadDOC(docptr, 2k_CDSN_IO + i); | |
| } | |
| } | |
| static void doc2000_readbuf_dword(struct mtd_info *mtd, u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("readbuf_dword of %d bytes: ", len); | |
| if (unlikely((((unsigned long)buf) | len) & 3)) { | |
| for (i = 0; i < len; i++) { | |
| *(uint8_t *) (&buf[i]) = ReadDOC(docptr, 2k_CDSN_IO + i); | |
| } | |
| } else { | |
| for (i = 0; i < len; i += 4) { | |
| *(uint32_t *) (&buf[i]) = readl(docptr + DoC_2k_CDSN_IO + i); | |
| } | |
| } | |
| } | |
| static int doc2000_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| for (i = 0; i < len; i++) | |
| if (buf[i] != ReadDOC(docptr, 2k_CDSN_IO)) | |
| return -EFAULT; | |
| return 0; | |
| } | |
| static uint16_t __init doc200x_ident_chip(struct mtd_info *mtd, int nr) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| uint16_t ret; | |
| doc200x_select_chip(mtd, nr); | |
| doc200x_hwcontrol(mtd, NAND_CMD_READID, | |
| NAND_CTRL_CLE | NAND_CTRL_CHANGE); | |
| doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); | |
| doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); | |
| /* We cant' use dev_ready here, but at least we wait for the | |
| * command to complete | |
| */ | |
| udelay(50); | |
| ret = this->read_byte(mtd) << 8; | |
| ret |= this->read_byte(mtd); | |
| if (doc->ChipID == DOC_ChipID_Doc2k && try_dword && !nr) { | |
| /* First chip probe. See if we get same results by 32-bit access */ | |
| union { | |
| uint32_t dword; | |
| uint8_t byte[4]; | |
| } ident; | |
| void __iomem *docptr = doc->virtadr; | |
| doc200x_hwcontrol(mtd, NAND_CMD_READID, | |
| NAND_CTRL_CLE | NAND_CTRL_CHANGE); | |
| doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); | |
| doc200x_hwcontrol(mtd, NAND_CMD_NONE, | |
| NAND_NCE | NAND_CTRL_CHANGE); | |
| udelay(50); | |
| ident.dword = readl(docptr + DoC_2k_CDSN_IO); | |
| if (((ident.byte[0] << 8) | ident.byte[1]) == ret) { | |
| printk(KERN_INFO "DiskOnChip 2000 responds to DWORD access\n"); | |
| this->read_buf = &doc2000_readbuf_dword; | |
| } | |
| } | |
| return ret; | |
| } | |
| static void __init doc2000_count_chips(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| uint16_t mfrid; | |
| int i; | |
| /* Max 4 chips per floor on DiskOnChip 2000 */ | |
| doc->chips_per_floor = 4; | |
| /* Find out what the first chip is */ | |
| mfrid = doc200x_ident_chip(mtd, 0); | |
| /* Find how many chips in each floor. */ | |
| for (i = 1; i < 4; i++) { | |
| if (doc200x_ident_chip(mtd, i) != mfrid) | |
| break; | |
| } | |
| doc->chips_per_floor = i; | |
| printk(KERN_DEBUG "Detected %d chips per floor.\n", i); | |
| } | |
| static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this) | |
| { | |
| struct doc_priv *doc = this->priv; | |
| int status; | |
| DoC_WaitReady(doc); | |
| this->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); | |
| DoC_WaitReady(doc); | |
| status = (int)this->read_byte(mtd); | |
| return status; | |
| } | |
| static void doc2001_write_byte(struct mtd_info *mtd, u_char datum) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| WriteDOC(datum, docptr, CDSNSlowIO); | |
| WriteDOC(datum, docptr, Mil_CDSN_IO); | |
| WriteDOC(datum, docptr, WritePipeTerm); | |
| } | |
| static u_char doc2001_read_byte(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| //ReadDOC(docptr, CDSNSlowIO); | |
| /* 11.4.5 -- delay twice to allow extended length cycle */ | |
| DoC_Delay(doc, 2); | |
| ReadDOC(docptr, ReadPipeInit); | |
| //return ReadDOC(docptr, Mil_CDSN_IO); | |
| return ReadDOC(docptr, LastDataRead); | |
| } | |
| static void doc2001_writebuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| for (i = 0; i < len; i++) | |
| WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); | |
| /* Terminate write pipeline */ | |
| WriteDOC(0x00, docptr, WritePipeTerm); | |
| } | |
| static void doc2001_readbuf(struct mtd_info *mtd, u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| /* Start read pipeline */ | |
| ReadDOC(docptr, ReadPipeInit); | |
| for (i = 0; i < len - 1; i++) | |
| buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff)); | |
| /* Terminate read pipeline */ | |
| buf[i] = ReadDOC(docptr, LastDataRead); | |
| } | |
| static int doc2001_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| /* Start read pipeline */ | |
| ReadDOC(docptr, ReadPipeInit); | |
| for (i = 0; i < len - 1; i++) | |
| if (buf[i] != ReadDOC(docptr, Mil_CDSN_IO)) { | |
| ReadDOC(docptr, LastDataRead); | |
| return i; | |
| } | |
| if (buf[i] != ReadDOC(docptr, LastDataRead)) | |
| return i; | |
| return 0; | |
| } | |
| static u_char doc2001plus_read_byte(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| u_char ret; | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| ret = ReadDOC(docptr, Mplus_LastDataRead); | |
| if (debug) | |
| printk("read_byte returns %02x\n", ret); | |
| return ret; | |
| } | |
| static void doc2001plus_writebuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("writebuf of %d bytes: ", len); | |
| for (i = 0; i < len; i++) { | |
| WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); | |
| if (debug && i < 16) | |
| printk("%02x ", buf[i]); | |
| } | |
| if (debug) | |
| printk("\n"); | |
| } | |
| static void doc2001plus_readbuf(struct mtd_info *mtd, u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("readbuf of %d bytes: ", len); | |
| /* Start read pipeline */ | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| for (i = 0; i < len - 2; i++) { | |
| buf[i] = ReadDOC(docptr, Mil_CDSN_IO); | |
| if (debug && i < 16) | |
| printk("%02x ", buf[i]); | |
| } | |
| /* Terminate read pipeline */ | |
| buf[len - 2] = ReadDOC(docptr, Mplus_LastDataRead); | |
| if (debug && i < 16) | |
| printk("%02x ", buf[len - 2]); | |
| buf[len - 1] = ReadDOC(docptr, Mplus_LastDataRead); | |
| if (debug && i < 16) | |
| printk("%02x ", buf[len - 1]); | |
| if (debug) | |
| printk("\n"); | |
| } | |
| static int doc2001plus_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| if (debug) | |
| printk("verifybuf of %d bytes: ", len); | |
| /* Start read pipeline */ | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| ReadDOC(docptr, Mplus_ReadPipeInit); | |
| for (i = 0; i < len - 2; i++) | |
| if (buf[i] != ReadDOC(docptr, Mil_CDSN_IO)) { | |
| ReadDOC(docptr, Mplus_LastDataRead); | |
| ReadDOC(docptr, Mplus_LastDataRead); | |
| return i; | |
| } | |
| if (buf[len - 2] != ReadDOC(docptr, Mplus_LastDataRead)) | |
| return len - 2; | |
| if (buf[len - 1] != ReadDOC(docptr, Mplus_LastDataRead)) | |
| return len - 1; | |
| return 0; | |
| } | |
| static void doc2001plus_select_chip(struct mtd_info *mtd, int chip) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int floor = 0; | |
| if (debug) | |
| printk("select chip (%d)\n", chip); | |
| if (chip == -1) { | |
| /* Disable flash internally */ | |
| WriteDOC(0, docptr, Mplus_FlashSelect); | |
| return; | |
| } | |
| floor = chip / doc->chips_per_floor; | |
| chip -= (floor * doc->chips_per_floor); | |
| /* Assert ChipEnable and deassert WriteProtect */ | |
| WriteDOC((DOC_FLASH_CE), docptr, Mplus_FlashSelect); | |
| this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); | |
| doc->curchip = chip; | |
| doc->curfloor = floor; | |
| } | |
| static void doc200x_select_chip(struct mtd_info *mtd, int chip) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int floor = 0; | |
| if (debug) | |
| printk("select chip (%d)\n", chip); | |
| if (chip == -1) | |
| return; | |
| floor = chip / doc->chips_per_floor; | |
| chip -= (floor * doc->chips_per_floor); | |
| /* 11.4.4 -- deassert CE before changing chip */ | |
| doc200x_hwcontrol(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); | |
| WriteDOC(floor, docptr, FloorSelect); | |
| WriteDOC(chip, docptr, CDSNDeviceSelect); | |
| doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); | |
| doc->curchip = chip; | |
| doc->curfloor = floor; | |
| } | |
| #define CDSN_CTRL_MSK (CDSN_CTRL_CE | CDSN_CTRL_CLE | CDSN_CTRL_ALE) | |
| static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, | |
| unsigned int ctrl) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| if (ctrl & NAND_CTRL_CHANGE) { | |
| doc->CDSNControl &= ~CDSN_CTRL_MSK; | |
| doc->CDSNControl |= ctrl & CDSN_CTRL_MSK; | |
| if (debug) | |
| printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl); | |
| WriteDOC(doc->CDSNControl, docptr, CDSNControl); | |
| /* 11.4.3 -- 4 NOPs after CSDNControl write */ | |
| DoC_Delay(doc, 4); | |
| } | |
| if (cmd != NAND_CMD_NONE) { | |
| if (DoC_is_2000(doc)) | |
| doc2000_write_byte(mtd, cmd); | |
| else | |
| doc2001_write_byte(mtd, cmd); | |
| } | |
| } | |
| static void doc2001plus_command(struct mtd_info *mtd, unsigned command, int column, int page_addr) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| /* | |
| * Must terminate write pipeline before sending any commands | |
| * to the device. | |
| */ | |
| if (command == NAND_CMD_PAGEPROG) { | |
| WriteDOC(0x00, docptr, Mplus_WritePipeTerm); | |
| WriteDOC(0x00, docptr, Mplus_WritePipeTerm); | |
| } | |
| /* | |
| * Write out the command to the device. | |
| */ | |
| if (command == NAND_CMD_SEQIN) { | |
| int readcmd; | |
| if (column >= mtd->writesize) { | |
| /* OOB area */ | |
| column -= mtd->writesize; | |
| readcmd = NAND_CMD_READOOB; | |
| } else if (column < 256) { | |
| /* First 256 bytes --> READ0 */ | |
| readcmd = NAND_CMD_READ0; | |
| } else { | |
| column -= 256; | |
| readcmd = NAND_CMD_READ1; | |
| } | |
| WriteDOC(readcmd, docptr, Mplus_FlashCmd); | |
| } | |
| WriteDOC(command, docptr, Mplus_FlashCmd); | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| if (column != -1 || page_addr != -1) { | |
| /* Serially input address */ | |
| if (column != -1) { | |
| /* Adjust columns for 16 bit buswidth */ | |
| if (this->options & NAND_BUSWIDTH_16) | |
| column >>= 1; | |
| WriteDOC(column, docptr, Mplus_FlashAddress); | |
| } | |
| if (page_addr != -1) { | |
| WriteDOC((unsigned char)(page_addr & 0xff), docptr, Mplus_FlashAddress); | |
| WriteDOC((unsigned char)((page_addr >> 8) & 0xff), docptr, Mplus_FlashAddress); | |
| /* One more address cycle for higher density devices */ | |
| if (this->chipsize & 0x0c000000) { | |
| WriteDOC((unsigned char)((page_addr >> 16) & 0x0f), docptr, Mplus_FlashAddress); | |
| printk("high density\n"); | |
| } | |
| } | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| /* deassert ALE */ | |
| if (command == NAND_CMD_READ0 || command == NAND_CMD_READ1 || | |
| command == NAND_CMD_READOOB || command == NAND_CMD_READID) | |
| WriteDOC(0, docptr, Mplus_FlashControl); | |
| } | |
| /* | |
| * program and erase have their own busy handlers | |
| * status and sequential in needs no delay | |
| */ | |
| switch (command) { | |
| case NAND_CMD_PAGEPROG: | |
| case NAND_CMD_ERASE1: | |
| case NAND_CMD_ERASE2: | |
| case NAND_CMD_SEQIN: | |
| case NAND_CMD_STATUS: | |
| return; | |
| case NAND_CMD_RESET: | |
| if (this->dev_ready) | |
| break; | |
| udelay(this->chip_delay); | |
| WriteDOC(NAND_CMD_STATUS, docptr, Mplus_FlashCmd); | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| WriteDOC(0, docptr, Mplus_WritePipeTerm); | |
| while (!(this->read_byte(mtd) & 0x40)) ; | |
| return; | |
| /* This applies to read commands */ | |
| default: | |
| /* | |
| * If we don't have access to the busy pin, we apply the given | |
| * command delay | |
| */ | |
| if (!this->dev_ready) { | |
| udelay(this->chip_delay); | |
| return; | |
| } | |
| } | |
| /* Apply this short delay always to ensure that we do wait tWB in | |
| * any case on any machine. */ | |
| ndelay(100); | |
| /* wait until command is processed */ | |
| while (!this->dev_ready(mtd)) ; | |
| } | |
| static int doc200x_dev_ready(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| if (DoC_is_MillenniumPlus(doc)) { | |
| /* 11.4.2 -- must NOP four times before checking FR/B# */ | |
| DoC_Delay(doc, 4); | |
| if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { | |
| if (debug) | |
| printk("not ready\n"); | |
| return 0; | |
| } | |
| if (debug) | |
| printk("was ready\n"); | |
| return 1; | |
| } else { | |
| /* 11.4.2 -- must NOP four times before checking FR/B# */ | |
| DoC_Delay(doc, 4); | |
| if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { | |
| if (debug) | |
| printk("not ready\n"); | |
| return 0; | |
| } | |
| /* 11.4.2 -- Must NOP twice if it's ready */ | |
| DoC_Delay(doc, 2); | |
| if (debug) | |
| printk("was ready\n"); | |
| return 1; | |
| } | |
| } | |
| static int doc200x_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) | |
| { | |
| /* This is our last resort if we couldn't find or create a BBT. Just | |
| pretend all blocks are good. */ | |
| return 0; | |
| } | |
| static void doc200x_enable_hwecc(struct mtd_info *mtd, int mode) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| /* Prime the ECC engine */ | |
| switch (mode) { | |
| case NAND_ECC_READ: | |
| WriteDOC(DOC_ECC_RESET, docptr, ECCConf); | |
| WriteDOC(DOC_ECC_EN, docptr, ECCConf); | |
| break; | |
| case NAND_ECC_WRITE: | |
| WriteDOC(DOC_ECC_RESET, docptr, ECCConf); | |
| WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf); | |
| break; | |
| } | |
| } | |
| static void doc2001plus_enable_hwecc(struct mtd_info *mtd, int mode) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| /* Prime the ECC engine */ | |
| switch (mode) { | |
| case NAND_ECC_READ: | |
| WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); | |
| WriteDOC(DOC_ECC_EN, docptr, Mplus_ECCConf); | |
| break; | |
| case NAND_ECC_WRITE: | |
| WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); | |
| WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, Mplus_ECCConf); | |
| break; | |
| } | |
| } | |
| /* This code is only called on write */ | |
| static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, unsigned char *ecc_code) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| int i; | |
| int emptymatch = 1; | |
| /* flush the pipeline */ | |
| if (DoC_is_2000(doc)) { | |
| WriteDOC(doc->CDSNControl & ~CDSN_CTRL_FLASH_IO, docptr, CDSNControl); | |
| WriteDOC(0, docptr, 2k_CDSN_IO); | |
| WriteDOC(0, docptr, 2k_CDSN_IO); | |
| WriteDOC(0, docptr, 2k_CDSN_IO); | |
| WriteDOC(doc->CDSNControl, docptr, CDSNControl); | |
| } else if (DoC_is_MillenniumPlus(doc)) { | |
| WriteDOC(0, docptr, Mplus_NOP); | |
| WriteDOC(0, docptr, Mplus_NOP); | |
| WriteDOC(0, docptr, Mplus_NOP); | |
| } else { | |
| WriteDOC(0, docptr, NOP); | |
| WriteDOC(0, docptr, NOP); | |
| WriteDOC(0, docptr, NOP); | |
| } | |
| for (i = 0; i < 6; i++) { | |
| if (DoC_is_MillenniumPlus(doc)) | |
| ecc_code[i] = ReadDOC_(docptr, DoC_Mplus_ECCSyndrome0 + i); | |
| else | |
| ecc_code[i] = ReadDOC_(docptr, DoC_ECCSyndrome0 + i); | |
| if (ecc_code[i] != empty_write_ecc[i]) | |
| emptymatch = 0; | |
| } | |
| if (DoC_is_MillenniumPlus(doc)) | |
| WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf); | |
| else | |
| WriteDOC(DOC_ECC_DIS, docptr, ECCConf); | |
| #if 0 | |
| /* If emptymatch=1, we might have an all-0xff data buffer. Check. */ | |
| if (emptymatch) { | |
| /* Note: this somewhat expensive test should not be triggered | |
| often. It could be optimized away by examining the data in | |
| the writebuf routine, and remembering the result. */ | |
| for (i = 0; i < 512; i++) { | |
| if (dat[i] == 0xff) | |
| continue; | |
| emptymatch = 0; | |
| break; | |
| } | |
| } | |
| /* If emptymatch still =1, we do have an all-0xff data buffer. | |
| Return all-0xff ecc value instead of the computed one, so | |
| it'll look just like a freshly-erased page. */ | |
| if (emptymatch) | |
| memset(ecc_code, 0xff, 6); | |
| #endif | |
| return 0; | |
| } | |
| static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, | |
| u_char *read_ecc, u_char *isnull) | |
| { | |
| int i, ret = 0; | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| void __iomem *docptr = doc->virtadr; | |
| uint8_t calc_ecc[6]; | |
| volatile u_char dummy; | |
| int emptymatch = 1; | |
| /* flush the pipeline */ | |
| if (DoC_is_2000(doc)) { | |
| dummy = ReadDOC(docptr, 2k_ECCStatus); | |
| dummy = ReadDOC(docptr, 2k_ECCStatus); | |
| dummy = ReadDOC(docptr, 2k_ECCStatus); | |
| } else if (DoC_is_MillenniumPlus(doc)) { | |
| dummy = ReadDOC(docptr, Mplus_ECCConf); | |
| dummy = ReadDOC(docptr, Mplus_ECCConf); | |
| dummy = ReadDOC(docptr, Mplus_ECCConf); | |
| } else { | |
| dummy = ReadDOC(docptr, ECCConf); | |
| dummy = ReadDOC(docptr, ECCConf); | |
| dummy = ReadDOC(docptr, ECCConf); | |
| } | |
| /* Error occured ? */ | |
| if (dummy & 0x80) { | |
| for (i = 0; i < 6; i++) { | |
| if (DoC_is_MillenniumPlus(doc)) | |
| calc_ecc[i] = ReadDOC_(docptr, DoC_Mplus_ECCSyndrome0 + i); | |
| else | |
| calc_ecc[i] = ReadDOC_(docptr, DoC_ECCSyndrome0 + i); | |
| if (calc_ecc[i] != empty_read_syndrome[i]) | |
| emptymatch = 0; | |
| } | |
| /* If emptymatch=1, the read syndrome is consistent with an | |
| all-0xff data and stored ecc block. Check the stored ecc. */ | |
| if (emptymatch) { | |
| for (i = 0; i < 6; i++) { | |
| if (read_ecc[i] == 0xff) | |
| continue; | |
| emptymatch = 0; | |
| break; | |
| } | |
| } | |
| /* If emptymatch still =1, check the data block. */ | |
| if (emptymatch) { | |
| /* Note: this somewhat expensive test should not be triggered | |
| often. It could be optimized away by examining the data in | |
| the readbuf routine, and remembering the result. */ | |
| for (i = 0; i < 512; i++) { | |
| if (dat[i] == 0xff) | |
| continue; | |
| emptymatch = 0; | |
| break; | |
| } | |
| } | |
| /* If emptymatch still =1, this is almost certainly a freshly- | |
| erased block, in which case the ECC will not come out right. | |
| We'll suppress the error and tell the caller everything's | |
| OK. Because it is. */ | |
| if (!emptymatch) | |
| ret = doc_ecc_decode(rs_decoder, dat, calc_ecc); | |
| if (ret > 0) | |
| printk(KERN_ERR "doc200x_correct_data corrected %d errors\n", ret); | |
| } | |
| if (DoC_is_MillenniumPlus(doc)) | |
| WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf); | |
| else | |
| WriteDOC(DOC_ECC_DIS, docptr, ECCConf); | |
| if (no_ecc_failures && (ret == -1)) { | |
| printk(KERN_ERR "suppressing ECC failure\n"); | |
| ret = 0; | |
| } | |
| return ret; | |
| } | |
| //u_char mydatabuf[528]; | |
| /* The strange out-of-order .oobfree list below is a (possibly unneeded) | |
| * attempt to retain compatibility. It used to read: | |
| * .oobfree = { {8, 8} } | |
| * Since that leaves two bytes unusable, it was changed. But the following | |
| * scheme might affect existing jffs2 installs by moving the cleanmarker: | |
| * .oobfree = { {6, 10} } | |
| * jffs2 seems to handle the above gracefully, but the current scheme seems | |
| * safer. The only problem with it is that any code that parses oobfree must | |
| * be able to handle out-of-order segments. | |
| */ | |
| static struct nand_ecclayout doc200x_oobinfo = { | |
| .eccbytes = 6, | |
| .eccpos = {0, 1, 2, 3, 4, 5}, | |
| .oobfree = {{8, 8}, {6, 2}} | |
| }; | |
| /* Find the (I)NFTL Media Header, and optionally also the mirror media header. | |
| On sucessful return, buf will contain a copy of the media header for | |
| further processing. id is the string to scan for, and will presumably be | |
| either "ANAND" or "BNAND". If findmirror=1, also look for the mirror media | |
| header. The page #s of the found media headers are placed in mh0_page and | |
| mh1_page in the DOC private structure. */ | |
| static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const char *id, int findmirror) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| unsigned offs; | |
| int ret; | |
| size_t retlen; | |
| for (offs = 0; offs < mtd->size; offs += mtd->erasesize) { | |
| ret = mtd->read(mtd, offs, mtd->writesize, &retlen, buf); | |
| if (retlen != mtd->writesize) | |
| continue; | |
| if (ret) { | |
| printk(KERN_WARNING "ECC error scanning DOC at 0x%x\n", offs); | |
| } | |
| if (memcmp(buf, id, 6)) | |
| continue; | |
| printk(KERN_INFO "Found DiskOnChip %s Media Header at 0x%x\n", id, offs); | |
| if (doc->mh0_page == -1) { | |
| doc->mh0_page = offs >> this->page_shift; | |
| if (!findmirror) | |
| return 1; | |
| continue; | |
| } | |
| doc->mh1_page = offs >> this->page_shift; | |
| return 2; | |
| } | |
| if (doc->mh0_page == -1) { | |
| printk(KERN_WARNING "DiskOnChip %s Media Header not found.\n", id); | |
| return 0; | |
| } | |
| /* Only one mediaheader was found. We want buf to contain a | |
| mediaheader on return, so we'll have to re-read the one we found. */ | |
| offs = doc->mh0_page << this->page_shift; | |
| ret = mtd->read(mtd, offs, mtd->writesize, &retlen, buf); | |
| if (retlen != mtd->writesize) { | |
| /* Insanity. Give up. */ | |
| printk(KERN_ERR "Read DiskOnChip Media Header once, but can't reread it???\n"); | |
| return 0; | |
| } | |
| return 1; | |
| } | |
| static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| int ret = 0; | |
| u_char *buf; | |
| struct NFTLMediaHeader *mh; | |
| const unsigned psize = 1 << this->page_shift; | |
| int numparts = 0; | |
| unsigned blocks, maxblocks; | |
| int offs, numheaders; | |
| buf = kmalloc(mtd->writesize, GFP_KERNEL); | |
| if (!buf) { | |
| printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); | |
| return 0; | |
| } | |
| if (!(numheaders = find_media_headers(mtd, buf, "ANAND", 1))) | |
| goto out; | |
| mh = (struct NFTLMediaHeader *)buf; | |
| mh->NumEraseUnits = le16_to_cpu(mh->NumEraseUnits); | |
| mh->FirstPhysicalEUN = le16_to_cpu(mh->FirstPhysicalEUN); | |
| mh->FormattedSize = le32_to_cpu(mh->FormattedSize); | |
| printk(KERN_INFO " DataOrgID = %s\n" | |
| " NumEraseUnits = %d\n" | |
| " FirstPhysicalEUN = %d\n" | |
| " FormattedSize = %d\n" | |
| " UnitSizeFactor = %d\n", | |
| mh->DataOrgID, mh->NumEraseUnits, | |
| mh->FirstPhysicalEUN, mh->FormattedSize, | |
| mh->UnitSizeFactor); | |
| blocks = mtd->size >> this->phys_erase_shift; | |
| maxblocks = min(32768U, mtd->erasesize - psize); | |
| if (mh->UnitSizeFactor == 0x00) { | |
| /* Auto-determine UnitSizeFactor. The constraints are: | |
| - There can be at most 32768 virtual blocks. | |
| - There can be at most (virtual block size - page size) | |
| virtual blocks (because MediaHeader+BBT must fit in 1). | |
| */ | |
| mh->UnitSizeFactor = 0xff; | |
| while (blocks > maxblocks) { | |
| blocks >>= 1; | |
| maxblocks = min(32768U, (maxblocks << 1) + psize); | |
| mh->UnitSizeFactor--; | |
| } | |
| printk(KERN_WARNING "UnitSizeFactor=0x00 detected. Correct value is assumed to be 0x%02x.\n", mh->UnitSizeFactor); | |
| } | |
| /* NOTE: The lines below modify internal variables of the NAND and MTD | |
| layers; variables with have already been configured by nand_scan. | |
| Unfortunately, we didn't know before this point what these values | |
| should be. Thus, this code is somewhat dependant on the exact | |
| implementation of the NAND layer. */ | |
| if (mh->UnitSizeFactor != 0xff) { | |
| this->bbt_erase_shift += (0xff - mh->UnitSizeFactor); | |
| mtd->erasesize <<= (0xff - mh->UnitSizeFactor); | |
| printk(KERN_INFO "Setting virtual erase size to %d\n", mtd->erasesize); | |
| blocks = mtd->size >> this->bbt_erase_shift; | |
| maxblocks = min(32768U, mtd->erasesize - psize); | |
| } | |
| if (blocks > maxblocks) { | |
| printk(KERN_ERR "UnitSizeFactor of 0x%02x is inconsistent with device size. Aborting.\n", mh->UnitSizeFactor); | |
| goto out; | |
| } | |
| /* Skip past the media headers. */ | |
| offs = max(doc->mh0_page, doc->mh1_page); | |
| offs <<= this->page_shift; | |
| offs += mtd->erasesize; | |
| if (show_firmware_partition == 1) { | |
| parts[0].name = " DiskOnChip Firmware / Media Header partition"; | |
| parts[0].offset = 0; | |
| parts[0].size = offs; | |
| numparts = 1; | |
| } | |
| parts[numparts].name = " DiskOnChip BDTL partition"; | |
| parts[numparts].offset = offs; | |
| parts[numparts].size = (mh->NumEraseUnits - numheaders) << this->bbt_erase_shift; | |
| offs += parts[numparts].size; | |
| numparts++; | |
| if (offs < mtd->size) { | |
| parts[numparts].name = " DiskOnChip Remainder partition"; | |
| parts[numparts].offset = offs; | |
| parts[numparts].size = mtd->size - offs; | |
| numparts++; | |
| } | |
| ret = numparts; | |
| out: | |
| kfree(buf); | |
| return ret; | |
| } | |
| /* This is a stripped-down copy of the code in inftlmount.c */ | |
| static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| int ret = 0; | |
| u_char *buf; | |
| struct INFTLMediaHeader *mh; | |
| struct INFTLPartition *ip; | |
| int numparts = 0; | |
| int blocks; | |
| int vshift, lastvunit = 0; | |
| int i; | |
| int end = mtd->size; | |
| if (inftl_bbt_write) | |
| end -= (INFTL_BBT_RESERVED_BLOCKS << this->phys_erase_shift); | |
| buf = kmalloc(mtd->writesize, GFP_KERNEL); | |
| if (!buf) { | |
| printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); | |
| return 0; | |
| } | |
| if (!find_media_headers(mtd, buf, "BNAND", 0)) | |
| goto out; | |
| doc->mh1_page = doc->mh0_page + (4096 >> this->page_shift); | |
| mh = (struct INFTLMediaHeader *)buf; | |
| mh->NoOfBootImageBlocks = le32_to_cpu(mh->NoOfBootImageBlocks); | |
| mh->NoOfBinaryPartitions = le32_to_cpu(mh->NoOfBinaryPartitions); | |
| mh->NoOfBDTLPartitions = le32_to_cpu(mh->NoOfBDTLPartitions); | |
| mh->BlockMultiplierBits = le32_to_cpu(mh->BlockMultiplierBits); | |
| mh->FormatFlags = le32_to_cpu(mh->FormatFlags); | |
| mh->PercentUsed = le32_to_cpu(mh->PercentUsed); | |
| printk(KERN_INFO " bootRecordID = %s\n" | |
| " NoOfBootImageBlocks = %d\n" | |
| " NoOfBinaryPartitions = %d\n" | |
| " NoOfBDTLPartitions = %d\n" | |
| " BlockMultiplerBits = %d\n" | |
| " FormatFlgs = %d\n" | |
| " OsakVersion = %d.%d.%d.%d\n" | |
| " PercentUsed = %d\n", | |
| mh->bootRecordID, mh->NoOfBootImageBlocks, | |
| mh->NoOfBinaryPartitions, | |
| mh->NoOfBDTLPartitions, | |
| mh->BlockMultiplierBits, mh->FormatFlags, | |
| ((unsigned char *) &mh->OsakVersion)[0] & 0xf, | |
| ((unsigned char *) &mh->OsakVersion)[1] & 0xf, | |
| ((unsigned char *) &mh->OsakVersion)[2] & 0xf, | |
| ((unsigned char *) &mh->OsakVersion)[3] & 0xf, | |
| mh->PercentUsed); | |
| vshift = this->phys_erase_shift + mh->BlockMultiplierBits; | |
| blocks = mtd->size >> vshift; | |
| if (blocks > 32768) { | |
| printk(KERN_ERR "BlockMultiplierBits=%d is inconsistent with device size. Aborting.\n", mh->BlockMultiplierBits); | |
| goto out; | |
| } | |
| blocks = doc->chips_per_floor << (this->chip_shift - this->phys_erase_shift); | |
| if (inftl_bbt_write && (blocks > mtd->erasesize)) { | |
| printk(KERN_ERR "Writeable BBTs spanning more than one erase block are not yet supported. FIX ME!\n"); | |
| goto out; | |
| } | |
| /* Scan the partitions */ | |
| for (i = 0; (i < 4); i++) { | |
| ip = &(mh->Partitions[i]); | |
| ip->virtualUnits = le32_to_cpu(ip->virtualUnits); | |
| ip->firstUnit = le32_to_cpu(ip->firstUnit); | |
| ip->lastUnit = le32_to_cpu(ip->lastUnit); | |
| ip->flags = le32_to_cpu(ip->flags); | |
| ip->spareUnits = le32_to_cpu(ip->spareUnits); | |
| ip->Reserved0 = le32_to_cpu(ip->Reserved0); | |
| printk(KERN_INFO " PARTITION[%d] ->\n" | |
| " virtualUnits = %d\n" | |
| " firstUnit = %d\n" | |
| " lastUnit = %d\n" | |
| " flags = 0x%x\n" | |
| " spareUnits = %d\n", | |
| i, ip->virtualUnits, ip->firstUnit, | |
| ip->lastUnit, ip->flags, | |
| ip->spareUnits); | |
| if ((show_firmware_partition == 1) && | |
| (i == 0) && (ip->firstUnit > 0)) { | |
| parts[0].name = " DiskOnChip IPL / Media Header partition"; | |
| parts[0].offset = 0; | |
| parts[0].size = mtd->erasesize * ip->firstUnit; | |
| numparts = 1; | |
| } | |
| if (ip->flags & INFTL_BINARY) | |
| parts[numparts].name = " DiskOnChip BDK partition"; | |
| else | |
| parts[numparts].name = " DiskOnChip BDTL partition"; | |
| parts[numparts].offset = ip->firstUnit << vshift; | |
| parts[numparts].size = (1 + ip->lastUnit - ip->firstUnit) << vshift; | |
| numparts++; | |
| if (ip->lastUnit > lastvunit) | |
| lastvunit = ip->lastUnit; | |
| if (ip->flags & INFTL_LAST) | |
| break; | |
| } | |
| lastvunit++; | |
| if ((lastvunit << vshift) < end) { | |
| parts[numparts].name = " DiskOnChip Remainder partition"; | |
| parts[numparts].offset = lastvunit << vshift; | |
| parts[numparts].size = end - parts[numparts].offset; | |
| numparts++; | |
| } | |
| ret = numparts; | |
| out: | |
| kfree(buf); | |
| return ret; | |
| } | |
| static int __init nftl_scan_bbt(struct mtd_info *mtd) | |
| { | |
| int ret, numparts; | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| struct mtd_partition parts[2]; | |
| memset((char *)parts, 0, sizeof(parts)); | |
| /* On NFTL, we have to find the media headers before we can read the | |
| BBTs, since they're stored in the media header eraseblocks. */ | |
| numparts = nftl_partscan(mtd, parts); | |
| if (!numparts) | |
| return -EIO; | |
| this->bbt_td->options = NAND_BBT_ABSPAGE | NAND_BBT_8BIT | | |
| NAND_BBT_SAVECONTENT | NAND_BBT_WRITE | | |
| NAND_BBT_VERSION; | |
| this->bbt_td->veroffs = 7; | |
| this->bbt_td->pages[0] = doc->mh0_page + 1; | |
| if (doc->mh1_page != -1) { | |
| this->bbt_md->options = NAND_BBT_ABSPAGE | NAND_BBT_8BIT | | |
| NAND_BBT_SAVECONTENT | NAND_BBT_WRITE | | |
| NAND_BBT_VERSION; | |
| this->bbt_md->veroffs = 7; | |
| this->bbt_md->pages[0] = doc->mh1_page + 1; | |
| } else { | |
| this->bbt_md = NULL; | |
| } | |
| /* It's safe to set bd=NULL below because NAND_BBT_CREATE is not set. | |
| At least as nand_bbt.c is currently written. */ | |
| if ((ret = nand_scan_bbt(mtd, NULL))) | |
| return ret; | |
| add_mtd_device(mtd); | |
| #ifdef CONFIG_MTD_PARTITIONS | |
| if (!no_autopart) | |
| add_mtd_partitions(mtd, parts, numparts); | |
| #endif | |
| return 0; | |
| } | |
| static int __init inftl_scan_bbt(struct mtd_info *mtd) | |
| { | |
| int ret, numparts; | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| struct mtd_partition parts[5]; | |
| if (this->numchips > doc->chips_per_floor) { | |
| printk(KERN_ERR "Multi-floor INFTL devices not yet supported.\n"); | |
| return -EIO; | |
| } | |
| if (DoC_is_MillenniumPlus(doc)) { | |
| this->bbt_td->options = NAND_BBT_2BIT | NAND_BBT_ABSPAGE; | |
| if (inftl_bbt_write) | |
| this->bbt_td->options |= NAND_BBT_WRITE; | |
| this->bbt_td->pages[0] = 2; | |
| this->bbt_md = NULL; | |
| } else { | |
| this->bbt_td->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; | |
| if (inftl_bbt_write) | |
| this->bbt_td->options |= NAND_BBT_WRITE; | |
| this->bbt_td->offs = 8; | |
| this->bbt_td->len = 8; | |
| this->bbt_td->veroffs = 7; | |
| this->bbt_td->maxblocks = INFTL_BBT_RESERVED_BLOCKS; | |
| this->bbt_td->reserved_block_code = 0x01; | |
| this->bbt_td->pattern = "MSYS_BBT"; | |
| this->bbt_md->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; | |
| if (inftl_bbt_write) | |
| this->bbt_md->options |= NAND_BBT_WRITE; | |
| this->bbt_md->offs = 8; | |
| this->bbt_md->len = 8; | |
| this->bbt_md->veroffs = 7; | |
| this->bbt_md->maxblocks = INFTL_BBT_RESERVED_BLOCKS; | |
| this->bbt_md->reserved_block_code = 0x01; | |
| this->bbt_md->pattern = "TBB_SYSM"; | |
| } | |
| /* It's safe to set bd=NULL below because NAND_BBT_CREATE is not set. | |
| At least as nand_bbt.c is currently written. */ | |
| if ((ret = nand_scan_bbt(mtd, NULL))) | |
| return ret; | |
| memset((char *)parts, 0, sizeof(parts)); | |
| numparts = inftl_partscan(mtd, parts); | |
| /* At least for now, require the INFTL Media Header. We could probably | |
| do without it for non-INFTL use, since all it gives us is | |
| autopartitioning, but I want to give it more thought. */ | |
| if (!numparts) | |
| return -EIO; | |
| add_mtd_device(mtd); | |
| #ifdef CONFIG_MTD_PARTITIONS | |
| if (!no_autopart) | |
| add_mtd_partitions(mtd, parts, numparts); | |
| #endif | |
| return 0; | |
| } | |
| static inline int __init doc2000_init(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| this->read_byte = doc2000_read_byte; | |
| this->write_buf = doc2000_writebuf; | |
| this->read_buf = doc2000_readbuf; | |
| this->verify_buf = doc2000_verifybuf; | |
| this->scan_bbt = nftl_scan_bbt; | |
| doc->CDSNControl = CDSN_CTRL_FLASH_IO | CDSN_CTRL_ECC_IO; | |
| doc2000_count_chips(mtd); | |
| mtd->name = "DiskOnChip 2000 (NFTL Model)"; | |
| return (4 * doc->chips_per_floor); | |
| } | |
| static inline int __init doc2001_init(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| this->read_byte = doc2001_read_byte; | |
| this->write_buf = doc2001_writebuf; | |
| this->read_buf = doc2001_readbuf; | |
| this->verify_buf = doc2001_verifybuf; | |
| ReadDOC(doc->virtadr, ChipID); | |
| ReadDOC(doc->virtadr, ChipID); | |
| ReadDOC(doc->virtadr, ChipID); | |
| if (ReadDOC(doc->virtadr, ChipID) != DOC_ChipID_DocMil) { | |
| /* It's not a Millennium; it's one of the newer | |
| DiskOnChip 2000 units with a similar ASIC. | |
| Treat it like a Millennium, except that it | |
| can have multiple chips. */ | |
| doc2000_count_chips(mtd); | |
| mtd->name = "DiskOnChip 2000 (INFTL Model)"; | |
| this->scan_bbt = inftl_scan_bbt; | |
| return (4 * doc->chips_per_floor); | |
| } else { | |
| /* Bog-standard Millennium */ | |
| doc->chips_per_floor = 1; | |
| mtd->name = "DiskOnChip Millennium"; | |
| this->scan_bbt = nftl_scan_bbt; | |
| return 1; | |
| } | |
| } | |
| static inline int __init doc2001plus_init(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *this = mtd->priv; | |
| struct doc_priv *doc = this->priv; | |
| this->read_byte = doc2001plus_read_byte; | |
| this->write_buf = doc2001plus_writebuf; | |
| this->read_buf = doc2001plus_readbuf; | |
| this->verify_buf = doc2001plus_verifybuf; | |
| this->scan_bbt = inftl_scan_bbt; | |
| this->cmd_ctrl = NULL; | |
| this->select_chip = doc2001plus_select_chip; | |
| this->cmdfunc = doc2001plus_command; | |
| this->ecc.hwctl = doc2001plus_enable_hwecc; | |
| doc->chips_per_floor = 1; | |
| mtd->name = "DiskOnChip Millennium Plus"; | |
| return 1; | |
| } | |
| static int __init doc_probe(unsigned long physadr) | |
| { | |
| unsigned char ChipID; | |
| struct mtd_info *mtd; | |
| struct nand_chip *nand; | |
| struct doc_priv *doc; | |
| void __iomem *virtadr; | |
| unsigned char save_control; | |
| unsigned char tmp, tmpb, tmpc; | |
| int reg, len, numchips; | |
| int ret = 0; | |
| virtadr = ioremap(physadr, DOC_IOREMAP_LEN); | |
| if (!virtadr) { | |
| printk(KERN_ERR "Diskonchip ioremap failed: 0x%x bytes at 0x%lx\n", DOC_IOREMAP_LEN, physadr); | |
| return -EIO; | |
| } | |
| /* It's not possible to cleanly detect the DiskOnChip - the | |
| * bootup procedure will put the device into reset mode, and | |
| * it's not possible to talk to it without actually writing | |
| * to the DOCControl register. So we store the current contents | |
| * of the DOCControl register's location, in case we later decide | |
| * that it's not a DiskOnChip, and want to put it back how we | |
| * found it. | |
| */ | |
| save_control = ReadDOC(virtadr, DOCControl); | |
| /* Reset the DiskOnChip ASIC */ | |
| WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); | |
| WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); | |
| /* Enable the DiskOnChip ASIC */ | |
| WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); | |
| WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); | |
| ChipID = ReadDOC(virtadr, ChipID); | |
| switch (ChipID) { | |
| case DOC_ChipID_Doc2k: | |
| reg = DoC_2k_ECCStatus; | |
| break; | |
| case DOC_ChipID_DocMil: | |
| reg = DoC_ECCConf; | |
| break; | |
| case DOC_ChipID_DocMilPlus16: | |
| case DOC_ChipID_DocMilPlus32: | |
| case 0: | |
| /* Possible Millennium Plus, need to do more checks */ | |
| /* Possibly release from power down mode */ | |
| for (tmp = 0; (tmp < 4); tmp++) | |
| ReadDOC(virtadr, Mplus_Power); | |
| /* Reset the Millennium Plus ASIC */ | |
| tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; | |
| WriteDOC(tmp, virtadr, Mplus_DOCControl); | |
| WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); | |
| mdelay(1); | |
| /* Enable the Millennium Plus ASIC */ | |
| tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; | |
| WriteDOC(tmp, virtadr, Mplus_DOCControl); | |
| WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); | |
| mdelay(1); | |
| ChipID = ReadDOC(virtadr, ChipID); | |
| switch (ChipID) { | |
| case DOC_ChipID_DocMilPlus16: | |
| reg = DoC_Mplus_Toggle; | |
| break; | |
| case DOC_ChipID_DocMilPlus32: | |
| printk(KERN_ERR "DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n"); | |
| default: | |
| ret = -ENODEV; | |
| goto notfound; | |
| } | |
| break; | |
| default: | |
| ret = -ENODEV; | |
| goto notfound; | |
| } | |
| /* Check the TOGGLE bit in the ECC register */ | |
| tmp = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; | |
| tmpb = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; | |
| tmpc = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; | |
| if ((tmp == tmpb) || (tmp != tmpc)) { | |
| printk(KERN_WARNING "Possible DiskOnChip at 0x%lx failed TOGGLE test, dropping.\n", physadr); | |
| ret = -ENODEV; | |
| goto notfound; | |
| } | |
| for (mtd = doclist; mtd; mtd = doc->nextdoc) { | |
| unsigned char oldval; | |
| unsigned char newval; | |
| nand = mtd->priv; | |
| doc = nand->priv; | |
| /* Use the alias resolution register to determine if this is | |
| in fact the same DOC aliased to a new address. If writes | |
| to one chip's alias resolution register change the value on | |
| the other chip, they're the same chip. */ | |
| if (ChipID == DOC_ChipID_DocMilPlus16) { | |
| oldval = ReadDOC(doc->virtadr, Mplus_AliasResolution); | |
| newval = ReadDOC(virtadr, Mplus_AliasResolution); | |
| } else { | |
| oldval = ReadDOC(doc->virtadr, AliasResolution); | |
| newval = ReadDOC(virtadr, AliasResolution); | |
| } | |
| if (oldval != newval) | |
| continue; | |
| if (ChipID == DOC_ChipID_DocMilPlus16) { | |
| WriteDOC(~newval, virtadr, Mplus_AliasResolution); | |
| oldval = ReadDOC(doc->virtadr, Mplus_AliasResolution); | |
| WriteDOC(newval, virtadr, Mplus_AliasResolution); // restore it | |
| } else { | |
| WriteDOC(~newval, virtadr, AliasResolution); | |
| oldval = ReadDOC(doc->virtadr, AliasResolution); | |
| WriteDOC(newval, virtadr, AliasResolution); // restore it | |
| } | |
| newval = ~newval; | |
| if (oldval == newval) { | |
| printk(KERN_DEBUG "Found alias of DOC at 0x%lx to 0x%lx\n", doc->physadr, physadr); | |
| goto notfound; | |
| } | |
| } | |
| printk(KERN_NOTICE "DiskOnChip found at 0x%lx\n", physadr); | |
| len = sizeof(struct mtd_info) + | |
| sizeof(struct nand_chip) + sizeof(struct doc_priv) + (2 * sizeof(struct nand_bbt_descr)); | |
| mtd = kzalloc(len, GFP_KERNEL); | |
| if (!mtd) { | |
| printk(KERN_ERR "DiskOnChip kmalloc (%d bytes) failed!\n", len); | |
| ret = -ENOMEM; | |
| goto fail; | |
| } | |
| nand = (struct nand_chip *) (mtd + 1); | |
| doc = (struct doc_priv *) (nand + 1); | |
| nand->bbt_td = (struct nand_bbt_descr *) (doc + 1); | |
| nand->bbt_md = nand->bbt_td + 1; | |
| mtd->priv = nand; | |
| mtd->owner = THIS_MODULE; | |
| nand->priv = doc; | |
| nand->select_chip = doc200x_select_chip; | |
| nand->cmd_ctrl = doc200x_hwcontrol; | |
| nand->dev_ready = doc200x_dev_ready; | |
| nand->waitfunc = doc200x_wait; | |
| nand->block_bad = doc200x_block_bad; | |
| nand->ecc.hwctl = doc200x_enable_hwecc; | |
| nand->ecc.calculate = doc200x_calculate_ecc; | |
| nand->ecc.correct = doc200x_correct_data; | |
| nand->ecc.layout = &doc200x_oobinfo; | |
| nand->ecc.mode = NAND_ECC_HW_SYNDROME; | |
| nand->ecc.size = 512; | |
| nand->ecc.bytes = 6; | |
| nand->options = NAND_USE_FLASH_BBT; | |
| doc->physadr = physadr; | |
| doc->virtadr = virtadr; | |
| doc->ChipID = ChipID; | |
| doc->curfloor = -1; | |
| doc->curchip = -1; | |
| doc->mh0_page = -1; | |
| doc->mh1_page = -1; | |
| doc->nextdoc = doclist; | |
| if (ChipID == DOC_ChipID_Doc2k) | |
| numchips = doc2000_init(mtd); | |
| else if (ChipID == DOC_ChipID_DocMilPlus16) | |
| numchips = doc2001plus_init(mtd); | |
| else | |
| numchips = doc2001_init(mtd); | |
| if ((ret = nand_scan(mtd, numchips))) { | |
| /* DBB note: i believe nand_release is necessary here, as | |
| buffers may have been allocated in nand_base. Check with | |
| Thomas. FIX ME! */ | |
| /* nand_release will call del_mtd_device, but we haven't yet | |
| added it. This is handled without incident by | |
| del_mtd_device, as far as I can tell. */ | |
| nand_release(mtd); | |
| kfree(mtd); | |
| goto fail; | |
| } | |
| /* Success! */ | |
| doclist = mtd; | |
| return 0; | |
| notfound: | |
| /* Put back the contents of the DOCControl register, in case it's not | |
| actually a DiskOnChip. */ | |
| WriteDOC(save_control, virtadr, DOCControl); | |
| fail: | |
| iounmap(virtadr); | |
| return ret; | |
| } | |
| static void release_nanddoc(void) | |
| { | |
| struct mtd_info *mtd, *nextmtd; | |
| struct nand_chip *nand; | |
| struct doc_priv *doc; | |
| for (mtd = doclist; mtd; mtd = nextmtd) { | |
| nand = mtd->priv; | |
| doc = nand->priv; | |
| nextmtd = doc->nextdoc; | |
| nand_release(mtd); | |
| iounmap(doc->virtadr); | |
| kfree(mtd); | |
| } | |
| } | |
| static int __init init_nanddoc(void) | |
| { | |
| int i, ret = 0; | |
| /* We could create the decoder on demand, if memory is a concern. | |
| * This way we have it handy, if an error happens | |
| * | |
| * Symbolsize is 10 (bits) | |
| * Primitve polynomial is x^10+x^3+1 | |
| * first consecutive root is 510 | |
| * primitve element to generate roots = 1 | |
| * generator polinomial degree = 4 | |
| */ | |
| rs_decoder = init_rs(10, 0x409, FCR, 1, NROOTS); | |
| if (!rs_decoder) { | |
| printk(KERN_ERR "DiskOnChip: Could not create a RS decoder\n"); | |
| return -ENOMEM; | |
| } | |
| if (doc_config_location) { | |
| printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location); | |
| ret = doc_probe(doc_config_location); | |
| if (ret < 0) | |
| goto outerr; | |
| } else { | |
| for (i = 0; (doc_locations[i] != 0xffffffff); i++) { | |
| doc_probe(doc_locations[i]); | |
| } | |
| } | |
| /* No banner message any more. Print a message if no DiskOnChip | |
| found, so the user knows we at least tried. */ | |
| if (!doclist) { | |
| printk(KERN_INFO "No valid DiskOnChip devices found\n"); | |
| ret = -ENODEV; | |
| goto outerr; | |
| } | |
| return 0; | |
| outerr: | |
| free_rs(rs_decoder); | |
| return ret; | |
| } | |
| static void __exit cleanup_nanddoc(void) | |
| { | |
| /* Cleanup the nand/DoC resources */ | |
| release_nanddoc(); | |
| /* Free the reed solomon resources */ | |
| if (rs_decoder) { | |
| free_rs(rs_decoder); | |
| } | |
| } | |
| module_init(init_nanddoc); | |
| module_exit(cleanup_nanddoc); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>"); | |
| MODULE_DESCRIPTION("M-Systems DiskOnChip 2000, Millennium and Millennium Plus device driver\n"); |