blob: aa8043089bb695133f19992d87deed7576c4f2db [file] [log] [blame]
#ifndef __ASM_SH64_PCI_H
#define __ASM_SH64_PCI_H
#ifdef __KERNEL__
#include <linux/dma-mapping.h>
/* Can be used to override the logic in pci_scan_bus for skipping
already-configured bus numbers - to be used for buggy BIOSes
or architectures with incomplete PCI setup by the loader */
#define pcibios_assign_all_busses() 1
* These are currently the correct values for the STM overdrive board
* We need some way of setting this on a board specific way, it will
* not be the same on other boards I think
#if defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
#define PCIBIOS_MIN_IO 0x2000
#define PCIBIOS_MIN_MEM 0x40000000
extern void pcibios_set_master(struct pci_dev *dev);
* Set penalize isa irq function
static inline void pcibios_penalize_isa_irq(int irq, int active)
/* We don't do dynamic PCI IRQ allocation */
/* Dynamic DMA mapping stuff.
* SuperH has everything mapped statically like x86.
/* The PCI address space does equal the physical memory
* address space. The networking and block device layers use
* this boolean for bounce buffer decisions.
#define PCI_DMA_BUS_IS_PHYS (1)
#include <linux/types.h>
#include <linux/slab.h>
#include <asm/scatterlist.h>
#include <linux/string.h>
#include <asm/io.h>
/* pci_unmap_{single,page} being a nop depends upon the
* configuration.
dma_addr_t ADDR_NAME;
__u32 LEN_NAME;
#define pci_unmap_addr(PTR, ADDR_NAME) \
#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL) \
(((PTR)->ADDR_NAME) = (VAL))
#define pci_unmap_len(PTR, LEN_NAME) \
#define pci_unmap_len_set(PTR, LEN_NAME, VAL) \
(((PTR)->LEN_NAME) = (VAL))
#define pci_unmap_addr(PTR, ADDR_NAME) (0)
#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL) do { } while (0)
#define pci_unmap_len(PTR, LEN_NAME) (0)
#define pci_unmap_len_set(PTR, LEN_NAME, VAL) do { } while (0)
/* Not supporting more than 32-bit PCI bus addresses now, but
* must satisfy references to this function. Change if needed.
#define pci_dac_dma_supported(pci_dev, mask) (0)
/* These macros should be used after a pci_map_sg call has been done
* to get bus addresses of each of the SG entries and their lengths.
* You should only work with the number of sg entries pci_map_sg
* returns, or alternatively stop on the first sg_dma_len(sg) which
* is 0.
#define sg_dma_address(sg) ((sg)->dma_address)
#define sg_dma_len(sg) ((sg)->length)
static inline void pci_dma_burst_advice(struct pci_dev *pdev,
enum pci_dma_burst_strategy *strat,
unsigned long *strategy_parameter)
*strategy_parameter = ~0UL;
/* Board-specific fixup routines. */
extern void pcibios_fixup(void);
extern void pcibios_fixup_irqs(void);
extern int pciauto_assign_resources(int busno, struct pci_channel *hose);
static inline void pcibios_add_platform_entries(struct pci_dev *dev)
#endif /* __KERNEL__ */
/* generic pci stuff */
#include <asm-generic/pci.h>
/* generic DMA-mapping stuff */
#include <asm-generic/pci-dma-compat.h>
#endif /* __ASM_SH64_PCI_H */