| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Cadence CDNSP DRD Driver. | |
| * | |
| * Copyright (C) 2020 Cadence. | |
| * | |
| * Author: Pawel Laszczak <pawell@cadence.com> | |
| * | |
| */ | |
| #include <linux/moduleparam.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/module.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/delay.h> | |
| #include <linux/log2.h> | |
| #include <linux/slab.h> | |
| #include <linux/pci.h> | |
| #include <linux/irq.h> | |
| #include <linux/dmi.h> | |
| #include "core.h" | |
| #include "gadget-export.h" | |
| #include "drd.h" | |
| #include "cdnsp-gadget.h" | |
| #include "cdnsp-trace.h" | |
| unsigned int cdnsp_port_speed(unsigned int port_status) | |
| { | |
| /*Detect gadget speed based on PORTSC register*/ | |
| if (DEV_SUPERSPEEDPLUS(port_status)) | |
| return USB_SPEED_SUPER_PLUS; | |
| else if (DEV_SUPERSPEED(port_status)) | |
| return USB_SPEED_SUPER; | |
| else if (DEV_HIGHSPEED(port_status)) | |
| return USB_SPEED_HIGH; | |
| else if (DEV_FULLSPEED(port_status)) | |
| return USB_SPEED_FULL; | |
| /* If device is detached then speed will be USB_SPEED_UNKNOWN.*/ | |
| return USB_SPEED_UNKNOWN; | |
| } | |
| /* | |
| * Given a port state, this function returns a value that would result in the | |
| * port being in the same state, if the value was written to the port status | |
| * control register. | |
| * Save Read Only (RO) bits and save read/write bits where | |
| * writing a 0 clears the bit and writing a 1 sets the bit (RWS). | |
| * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect. | |
| */ | |
| u32 cdnsp_port_state_to_neutral(u32 state) | |
| { | |
| /* Save read-only status and port state. */ | |
| return (state & CDNSP_PORT_RO) | (state & CDNSP_PORT_RWS); | |
| } | |
| /** | |
| * cdnsp_find_next_ext_cap - Find the offset of the extended capabilities | |
| * with capability ID id. | |
| * @base: PCI MMIO registers base address. | |
| * @start: Address at which to start looking, (0 or HCC_PARAMS to start at | |
| * beginning of list) | |
| * @id: Extended capability ID to search for. | |
| * | |
| * Returns the offset of the next matching extended capability structure. | |
| * Some capabilities can occur several times, | |
| * e.g., the EXT_CAPS_PROTOCOL, and this provides a way to find them all. | |
| */ | |
| int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id) | |
| { | |
| u32 offset = start; | |
| u32 next; | |
| u32 val; | |
| if (!start || start == HCC_PARAMS_OFFSET) { | |
| val = readl(base + HCC_PARAMS_OFFSET); | |
| if (val == ~0) | |
| return 0; | |
| offset = HCC_EXT_CAPS(val) << 2; | |
| if (!offset) | |
| return 0; | |
| } | |
| do { | |
| val = readl(base + offset); | |
| if (val == ~0) | |
| return 0; | |
| if (EXT_CAPS_ID(val) == id && offset != start) | |
| return offset; | |
| next = EXT_CAPS_NEXT(val); | |
| offset += next << 2; | |
| } while (next); | |
| return 0; | |
| } | |
| void cdnsp_set_link_state(struct cdnsp_device *pdev, | |
| __le32 __iomem *port_regs, | |
| u32 link_state) | |
| { | |
| int port_num = 0xFF; | |
| u32 temp; | |
| temp = readl(port_regs); | |
| temp = cdnsp_port_state_to_neutral(temp); | |
| temp |= PORT_WKCONN_E | PORT_WKDISC_E; | |
| writel(temp, port_regs); | |
| temp &= ~PORT_PLS_MASK; | |
| temp |= PORT_LINK_STROBE | link_state; | |
| if (pdev->active_port) | |
| port_num = pdev->active_port->port_num; | |
| trace_cdnsp_handle_port_status(port_num, readl(port_regs)); | |
| writel(temp, port_regs); | |
| trace_cdnsp_link_state_changed(port_num, readl(port_regs)); | |
| } | |
| static void cdnsp_disable_port(struct cdnsp_device *pdev, | |
| __le32 __iomem *port_regs) | |
| { | |
| u32 temp = cdnsp_port_state_to_neutral(readl(port_regs)); | |
| writel(temp | PORT_PED, port_regs); | |
| } | |
| static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev, | |
| __le32 __iomem *port_regs) | |
| { | |
| u32 portsc = readl(port_regs); | |
| writel(cdnsp_port_state_to_neutral(portsc) | | |
| (portsc & PORT_CHANGE_BITS), port_regs); | |
| } | |
| static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit) | |
| { | |
| __le32 __iomem *reg; | |
| void __iomem *base; | |
| u32 offset = 0; | |
| base = &pdev->cap_regs->hc_capbase; | |
| offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP); | |
| reg = base + offset + REG_CHICKEN_BITS_2_OFFSET; | |
| bit = readl(reg) | bit; | |
| writel(bit, reg); | |
| } | |
| static void cdnsp_clear_chicken_bits_2(struct cdnsp_device *pdev, u32 bit) | |
| { | |
| __le32 __iomem *reg; | |
| void __iomem *base; | |
| u32 offset = 0; | |
| base = &pdev->cap_regs->hc_capbase; | |
| offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP); | |
| reg = base + offset + REG_CHICKEN_BITS_2_OFFSET; | |
| bit = readl(reg) & ~bit; | |
| writel(bit, reg); | |
| } | |
| /* | |
| * Disable interrupts and begin the controller halting process. | |
| */ | |
| static void cdnsp_quiesce(struct cdnsp_device *pdev) | |
| { | |
| u32 halted; | |
| u32 mask; | |
| u32 cmd; | |
| mask = ~(u32)(CDNSP_IRQS); | |
| halted = readl(&pdev->op_regs->status) & STS_HALT; | |
| if (!halted) | |
| mask &= ~(CMD_R_S | CMD_DEVEN); | |
| cmd = readl(&pdev->op_regs->command); | |
| cmd &= mask; | |
| writel(cmd, &pdev->op_regs->command); | |
| } | |
| /* | |
| * Force controller into halt state. | |
| * | |
| * Disable any IRQs and clear the run/stop bit. | |
| * Controller will complete any current and actively pipelined transactions, and | |
| * should halt within 16 ms of the run/stop bit being cleared. | |
| * Read controller Halted bit in the status register to see when the | |
| * controller is finished. | |
| */ | |
| int cdnsp_halt(struct cdnsp_device *pdev) | |
| { | |
| int ret; | |
| u32 val; | |
| cdnsp_quiesce(pdev); | |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, val, | |
| val & STS_HALT, 1, | |
| CDNSP_MAX_HALT_USEC); | |
| if (ret) { | |
| dev_err(pdev->dev, "ERROR: Device halt failed\n"); | |
| return ret; | |
| } | |
| pdev->cdnsp_state |= CDNSP_STATE_HALTED; | |
| return 0; | |
| } | |
| /* | |
| * device controller died, register read returns 0xffffffff, or command never | |
| * ends. | |
| */ | |
| void cdnsp_died(struct cdnsp_device *pdev) | |
| { | |
| dev_err(pdev->dev, "ERROR: CDNSP controller not responding\n"); | |
| pdev->cdnsp_state |= CDNSP_STATE_DYING; | |
| cdnsp_halt(pdev); | |
| } | |
| /* | |
| * Set the run bit and wait for the device to be running. | |
| */ | |
| static int cdnsp_start(struct cdnsp_device *pdev) | |
| { | |
| u32 temp; | |
| int ret; | |
| temp = readl(&pdev->op_regs->command); | |
| temp |= (CMD_R_S | CMD_DEVEN); | |
| writel(temp, &pdev->op_regs->command); | |
| pdev->cdnsp_state = 0; | |
| /* | |
| * Wait for the STS_HALT Status bit to be 0 to indicate the device is | |
| * running. | |
| */ | |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp, | |
| !(temp & STS_HALT), 1, | |
| CDNSP_MAX_HALT_USEC); | |
| if (ret) { | |
| pdev->cdnsp_state = CDNSP_STATE_DYING; | |
| dev_err(pdev->dev, "ERROR: Controller run failed\n"); | |
| } | |
| return ret; | |
| } | |
| /* | |
| * Reset a halted controller. | |
| * | |
| * This resets pipelines, timers, counters, state machines, etc. | |
| * Transactions will be terminated immediately, and operational registers | |
| * will be set to their defaults. | |
| */ | |
| int cdnsp_reset(struct cdnsp_device *pdev) | |
| { | |
| u32 command; | |
| u32 temp; | |
| int ret; | |
| temp = readl(&pdev->op_regs->status); | |
| if (temp == ~(u32)0) { | |
| dev_err(pdev->dev, "Device not accessible, reset failed.\n"); | |
| return -ENODEV; | |
| } | |
| if ((temp & STS_HALT) == 0) { | |
| dev_err(pdev->dev, "Controller not halted, aborting reset.\n"); | |
| return -EINVAL; | |
| } | |
| command = readl(&pdev->op_regs->command); | |
| command |= CMD_RESET; | |
| writel(command, &pdev->op_regs->command); | |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->command, temp, | |
| !(temp & CMD_RESET), 1, | |
| 10 * 1000); | |
| if (ret) { | |
| dev_err(pdev->dev, "ERROR: Controller reset failed\n"); | |
| return ret; | |
| } | |
| /* | |
| * CDNSP cannot write any doorbells or operational registers other | |
| * than status until the "Controller Not Ready" flag is cleared. | |
| */ | |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp, | |
| !(temp & STS_CNR), 1, | |
| 10 * 1000); | |
| if (ret) { | |
| dev_err(pdev->dev, "ERROR: Controller not ready to work\n"); | |
| return ret; | |
| } | |
| dev_dbg(pdev->dev, "Controller ready to work"); | |
| return ret; | |
| } | |
| /* | |
| * cdnsp_get_endpoint_index - Find the index for an endpoint given its | |
| * descriptor.Use the return value to right shift 1 for the bitmask. | |
| * | |
| * Index = (epnum * 2) + direction - 1, | |
| * where direction = 0 for OUT, 1 for IN. | |
| * For control endpoints, the IN index is used (OUT index is unused), so | |
| * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2) | |
| */ | |
| static unsigned int | |
| cdnsp_get_endpoint_index(const struct usb_endpoint_descriptor *desc) | |
| { | |
| unsigned int index = (unsigned int)usb_endpoint_num(desc); | |
| if (usb_endpoint_xfer_control(desc)) | |
| return index * 2; | |
| return (index * 2) + (usb_endpoint_dir_in(desc) ? 1 : 0) - 1; | |
| } | |
| /* | |
| * Find the flag for this endpoint (for use in the control context). Use the | |
| * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is | |
| * bit 1, etc. | |
| */ | |
| static unsigned int | |
| cdnsp_get_endpoint_flag(const struct usb_endpoint_descriptor *desc) | |
| { | |
| return 1 << (cdnsp_get_endpoint_index(desc) + 1); | |
| } | |
| int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq) | |
| { | |
| struct cdnsp_device *pdev = pep->pdev; | |
| struct usb_request *request; | |
| int ret; | |
| if (preq->epnum == 0 && !list_empty(&pep->pending_list)) { | |
| trace_cdnsp_request_enqueue_busy(preq); | |
| return -EBUSY; | |
| } | |
| request = &preq->request; | |
| request->actual = 0; | |
| request->status = -EINPROGRESS; | |
| preq->direction = pep->direction; | |
| preq->epnum = pep->number; | |
| preq->td.drbl = 0; | |
| ret = usb_gadget_map_request_by_dev(pdev->dev, request, pep->direction); | |
| if (ret) { | |
| trace_cdnsp_request_enqueue_error(preq); | |
| return ret; | |
| } | |
| list_add_tail(&preq->list, &pep->pending_list); | |
| trace_cdnsp_request_enqueue(preq); | |
| switch (usb_endpoint_type(pep->endpoint.desc)) { | |
| case USB_ENDPOINT_XFER_CONTROL: | |
| ret = cdnsp_queue_ctrl_tx(pdev, preq); | |
| break; | |
| case USB_ENDPOINT_XFER_BULK: | |
| case USB_ENDPOINT_XFER_INT: | |
| ret = cdnsp_queue_bulk_tx(pdev, preq); | |
| break; | |
| case USB_ENDPOINT_XFER_ISOC: | |
| ret = cdnsp_queue_isoc_tx(pdev, preq); | |
| } | |
| if (ret) | |
| goto unmap; | |
| return 0; | |
| unmap: | |
| usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request, | |
| pep->direction); | |
| list_del(&preq->list); | |
| trace_cdnsp_request_enqueue_error(preq); | |
| return ret; | |
| } | |
| /* | |
| * Remove the request's TD from the endpoint ring. This may cause the | |
| * controller to stop USB transfers, potentially stopping in the middle of a | |
| * TRB buffer. The controller should pick up where it left off in the TD, | |
| * unless a Set Transfer Ring Dequeue Pointer is issued. | |
| * | |
| * The TRBs that make up the buffers for the canceled request will be "removed" | |
| * from the ring. Since the ring is a contiguous structure, they can't be | |
| * physically removed. Instead, there are two options: | |
| * | |
| * 1) If the controller is in the middle of processing the request to be | |
| * canceled, we simply move the ring's dequeue pointer past those TRBs | |
| * using the Set Transfer Ring Dequeue Pointer command. This will be | |
| * the common case, when drivers timeout on the last submitted request | |
| * and attempt to cancel. | |
| * | |
| * 2) If the controller is in the middle of a different TD, we turn the TRBs | |
| * into a series of 1-TRB transfer no-op TDs. No-ops shouldn't be chained. | |
| * The controller will need to invalidate the any TRBs it has cached after | |
| * the stop endpoint command. | |
| * | |
| * 3) The TD may have completed by the time the Stop Endpoint Command | |
| * completes, so software needs to handle that case too. | |
| * | |
| */ | |
| int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq) | |
| { | |
| struct cdnsp_device *pdev = pep->pdev; | |
| int ret_stop = 0; | |
| int ret_rem; | |
| trace_cdnsp_request_dequeue(preq); | |
| if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_RUNNING) | |
| ret_stop = cdnsp_cmd_stop_ep(pdev, pep); | |
| ret_rem = cdnsp_remove_request(pdev, preq, pep); | |
| return ret_rem ? ret_rem : ret_stop; | |
| } | |
| static void cdnsp_zero_in_ctx(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_input_control_ctx *ctrl_ctx; | |
| struct cdnsp_slot_ctx *slot_ctx; | |
| struct cdnsp_ep_ctx *ep_ctx; | |
| int i; | |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); | |
| /* | |
| * When a device's add flag and drop flag are zero, any subsequent | |
| * configure endpoint command will leave that endpoint's state | |
| * untouched. Make sure we don't leave any old state in the input | |
| * endpoint contexts. | |
| */ | |
| ctrl_ctx->drop_flags = 0; | |
| ctrl_ctx->add_flags = 0; | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); | |
| slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK); | |
| /* Endpoint 0 is always valid */ | |
| slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1)); | |
| for (i = 1; i < CDNSP_ENDPOINTS_NUM; ++i) { | |
| ep_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, i); | |
| ep_ctx->ep_info = 0; | |
| ep_ctx->ep_info2 = 0; | |
| ep_ctx->deq = 0; | |
| ep_ctx->tx_info = 0; | |
| } | |
| } | |
| /* Issue a configure endpoint command and wait for it to finish. */ | |
| static int cdnsp_configure_endpoint(struct cdnsp_device *pdev) | |
| { | |
| int ret; | |
| cdnsp_queue_configure_endpoint(pdev, pdev->cmd.in_ctx->dma); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| if (ret) { | |
| dev_err(pdev->dev, | |
| "ERR: unexpected command completion code 0x%x.\n", ret); | |
| return -EINVAL; | |
| } | |
| return ret; | |
| } | |
| static void cdnsp_invalidate_ep_events(struct cdnsp_device *pdev, | |
| struct cdnsp_ep *pep) | |
| { | |
| struct cdnsp_segment *segment; | |
| union cdnsp_trb *event; | |
| u32 cycle_state; | |
| u32 data; | |
| event = pdev->event_ring->dequeue; | |
| segment = pdev->event_ring->deq_seg; | |
| cycle_state = pdev->event_ring->cycle_state; | |
| while (1) { | |
| data = le32_to_cpu(event->trans_event.flags); | |
| /* Check the owner of the TRB. */ | |
| if ((data & TRB_CYCLE) != cycle_state) | |
| break; | |
| if (TRB_FIELD_TO_TYPE(data) == TRB_TRANSFER && | |
| TRB_TO_EP_ID(data) == (pep->idx + 1)) { | |
| data |= TRB_EVENT_INVALIDATE; | |
| event->trans_event.flags = cpu_to_le32(data); | |
| } | |
| if (cdnsp_last_trb_on_seg(segment, event)) { | |
| cycle_state ^= 1; | |
| segment = pdev->event_ring->deq_seg->next; | |
| event = segment->trbs; | |
| } else { | |
| event++; | |
| } | |
| } | |
| } | |
| int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_segment *event_deq_seg; | |
| union cdnsp_trb *cmd_trb; | |
| dma_addr_t cmd_deq_dma; | |
| union cdnsp_trb *event; | |
| u32 cycle_state; | |
| int ret, val; | |
| u64 cmd_dma; | |
| u32 flags; | |
| cmd_trb = pdev->cmd.command_trb; | |
| pdev->cmd.status = 0; | |
| trace_cdnsp_cmd_wait_for_compl(pdev->cmd_ring, &cmd_trb->generic); | |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->cmd_ring, val, | |
| !CMD_RING_BUSY(val), 1, | |
| CDNSP_CMD_TIMEOUT); | |
| if (ret) { | |
| dev_err(pdev->dev, "ERR: Timeout while waiting for command\n"); | |
| trace_cdnsp_cmd_timeout(pdev->cmd_ring, &cmd_trb->generic); | |
| pdev->cdnsp_state = CDNSP_STATE_DYING; | |
| return -ETIMEDOUT; | |
| } | |
| event = pdev->event_ring->dequeue; | |
| event_deq_seg = pdev->event_ring->deq_seg; | |
| cycle_state = pdev->event_ring->cycle_state; | |
| cmd_deq_dma = cdnsp_trb_virt_to_dma(pdev->cmd_ring->deq_seg, cmd_trb); | |
| if (!cmd_deq_dma) | |
| return -EINVAL; | |
| while (1) { | |
| flags = le32_to_cpu(event->event_cmd.flags); | |
| /* Check the owner of the TRB. */ | |
| if ((flags & TRB_CYCLE) != cycle_state) | |
| return -EINVAL; | |
| cmd_dma = le64_to_cpu(event->event_cmd.cmd_trb); | |
| /* | |
| * Check whether the completion event is for last queued | |
| * command. | |
| */ | |
| if (TRB_FIELD_TO_TYPE(flags) != TRB_COMPLETION || | |
| cmd_dma != (u64)cmd_deq_dma) { | |
| if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) { | |
| event++; | |
| continue; | |
| } | |
| if (cdnsp_last_trb_on_ring(pdev->event_ring, | |
| event_deq_seg, event)) | |
| cycle_state ^= 1; | |
| event_deq_seg = event_deq_seg->next; | |
| event = event_deq_seg->trbs; | |
| continue; | |
| } | |
| trace_cdnsp_handle_command(pdev->cmd_ring, &cmd_trb->generic); | |
| pdev->cmd.status = GET_COMP_CODE(le32_to_cpu(event->event_cmd.status)); | |
| if (pdev->cmd.status == COMP_SUCCESS) | |
| return 0; | |
| return -pdev->cmd.status; | |
| } | |
| } | |
| int cdnsp_halt_endpoint(struct cdnsp_device *pdev, | |
| struct cdnsp_ep *pep, | |
| int value) | |
| { | |
| int ret; | |
| trace_cdnsp_ep_halt(value ? "Set" : "Clear"); | |
| ret = cdnsp_cmd_stop_ep(pdev, pep); | |
| if (ret) | |
| return ret; | |
| if (value) { | |
| if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) { | |
| cdnsp_queue_halt_endpoint(pdev, pep->idx); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| } | |
| pep->ep_state |= EP_HALTED; | |
| } else { | |
| cdnsp_queue_reset_ep(pdev, pep->idx); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| trace_cdnsp_handle_cmd_reset_ep(pep->out_ctx); | |
| if (ret) | |
| return ret; | |
| pep->ep_state &= ~EP_HALTED; | |
| if (pep->idx != 0 && !(pep->ep_state & EP_WEDGE)) | |
| cdnsp_ring_doorbell_for_active_rings(pdev, pep); | |
| pep->ep_state &= ~EP_WEDGE; | |
| } | |
| return 0; | |
| } | |
| static int cdnsp_update_eps_configuration(struct cdnsp_device *pdev, | |
| struct cdnsp_ep *pep) | |
| { | |
| struct cdnsp_input_control_ctx *ctrl_ctx; | |
| struct cdnsp_slot_ctx *slot_ctx; | |
| int ret = 0; | |
| u32 ep_sts; | |
| int i; | |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); | |
| /* Don't issue the command if there's no endpoints to update. */ | |
| if (ctrl_ctx->add_flags == 0 && ctrl_ctx->drop_flags == 0) | |
| return 0; | |
| ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG); | |
| ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG); | |
| ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG)); | |
| /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */ | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); | |
| for (i = CDNSP_ENDPOINTS_NUM; i >= 1; i--) { | |
| __le32 le32 = cpu_to_le32(BIT(i)); | |
| if ((pdev->eps[i - 1].ring && !(ctrl_ctx->drop_flags & le32)) || | |
| (ctrl_ctx->add_flags & le32) || i == 1) { | |
| slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK); | |
| slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i)); | |
| break; | |
| } | |
| } | |
| ep_sts = GET_EP_CTX_STATE(pep->out_ctx); | |
| if ((ctrl_ctx->add_flags != cpu_to_le32(SLOT_FLAG) && | |
| ep_sts == EP_STATE_DISABLED) || | |
| (ep_sts != EP_STATE_DISABLED && ctrl_ctx->drop_flags)) | |
| ret = cdnsp_configure_endpoint(pdev); | |
| trace_cdnsp_configure_endpoint(cdnsp_get_slot_ctx(&pdev->out_ctx)); | |
| trace_cdnsp_handle_cmd_config_ep(pep->out_ctx); | |
| cdnsp_zero_in_ctx(pdev); | |
| return ret; | |
| } | |
| /* | |
| * This submits a Reset Device Command, which will set the device state to 0, | |
| * set the device address to 0, and disable all the endpoints except the default | |
| * control endpoint. The USB core should come back and call | |
| * cdnsp_setup_device(), and then re-set up the configuration. | |
| */ | |
| int cdnsp_reset_device(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_slot_ctx *slot_ctx; | |
| int slot_state; | |
| int ret, i; | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); | |
| slot_ctx->dev_info = 0; | |
| pdev->device_address = 0; | |
| /* If device is not setup, there is no point in resetting it. */ | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); | |
| slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); | |
| trace_cdnsp_reset_device(slot_ctx); | |
| if (slot_state <= SLOT_STATE_DEFAULT && | |
| pdev->eps[0].ep_state & EP_HALTED) { | |
| cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0); | |
| } | |
| /* | |
| * During Reset Device command controller shall transition the | |
| * endpoint ep0 to the Running State. | |
| */ | |
| pdev->eps[0].ep_state &= ~(EP_STOPPED | EP_HALTED); | |
| pdev->eps[0].ep_state |= EP_ENABLED; | |
| if (slot_state <= SLOT_STATE_DEFAULT) | |
| return 0; | |
| cdnsp_queue_reset_device(pdev); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| /* | |
| * After Reset Device command all not default endpoints | |
| * are in Disabled state. | |
| */ | |
| for (i = 1; i < CDNSP_ENDPOINTS_NUM; ++i) | |
| pdev->eps[i].ep_state |= EP_STOPPED | EP_UNCONFIGURED; | |
| trace_cdnsp_handle_cmd_reset_dev(slot_ctx); | |
| if (ret) | |
| dev_err(pdev->dev, "Reset device failed with error code %d", | |
| ret); | |
| return ret; | |
| } | |
| /* | |
| * Sets the MaxPStreams field and the Linear Stream Array field. | |
| * Sets the dequeue pointer to the stream context array. | |
| */ | |
| static void cdnsp_setup_streams_ep_input_ctx(struct cdnsp_device *pdev, | |
| struct cdnsp_ep_ctx *ep_ctx, | |
| struct cdnsp_stream_info *stream_info) | |
| { | |
| u32 max_primary_streams; | |
| /* MaxPStreams is the number of stream context array entries, not the | |
| * number we're actually using. Must be in 2^(MaxPstreams + 1) format. | |
| * fls(0) = 0, fls(0x1) = 1, fls(0x10) = 2, fls(0x100) = 3, etc. | |
| */ | |
| max_primary_streams = fls(stream_info->num_stream_ctxs) - 2; | |
| ep_ctx->ep_info &= cpu_to_le32(~EP_MAXPSTREAMS_MASK); | |
| ep_ctx->ep_info |= cpu_to_le32(EP_MAXPSTREAMS(max_primary_streams) | |
| | EP_HAS_LSA); | |
| ep_ctx->deq = cpu_to_le64(stream_info->ctx_array_dma); | |
| } | |
| /* | |
| * The drivers use this function to prepare a bulk endpoints to use streams. | |
| * | |
| * Don't allow the call to succeed if endpoint only supports one stream | |
| * (which means it doesn't support streams at all). | |
| */ | |
| int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep) | |
| { | |
| unsigned int num_streams = usb_ss_max_streams(pep->endpoint.comp_desc); | |
| unsigned int num_stream_ctxs; | |
| int ret; | |
| if (num_streams == 0) | |
| return 0; | |
| if (num_streams > STREAM_NUM_STREAMS) | |
| return -EINVAL; | |
| /* | |
| * Add two to the number of streams requested to account for | |
| * stream 0 that is reserved for controller usage and one additional | |
| * for TASK SET FULL response. | |
| */ | |
| num_streams += 2; | |
| /* The stream context array size must be a power of two */ | |
| num_stream_ctxs = roundup_pow_of_two(num_streams); | |
| trace_cdnsp_stream_number(pep, num_stream_ctxs, num_streams); | |
| ret = cdnsp_alloc_stream_info(pdev, pep, num_stream_ctxs, num_streams); | |
| if (ret) | |
| return ret; | |
| cdnsp_setup_streams_ep_input_ctx(pdev, pep->in_ctx, &pep->stream_info); | |
| pep->ep_state |= EP_HAS_STREAMS; | |
| pep->stream_info.td_count = 0; | |
| pep->stream_info.first_prime_det = 0; | |
| /* Subtract 1 for stream 0, which drivers can't use. */ | |
| return num_streams - 1; | |
| } | |
| int cdnsp_disable_slot(struct cdnsp_device *pdev) | |
| { | |
| int ret; | |
| cdnsp_queue_slot_control(pdev, TRB_DISABLE_SLOT); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| pdev->slot_id = 0; | |
| pdev->active_port = NULL; | |
| trace_cdnsp_handle_cmd_disable_slot(cdnsp_get_slot_ctx(&pdev->out_ctx)); | |
| memset(pdev->in_ctx.bytes, 0, CDNSP_CTX_SIZE); | |
| memset(pdev->out_ctx.bytes, 0, CDNSP_CTX_SIZE); | |
| return ret; | |
| } | |
| int cdnsp_enable_slot(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_slot_ctx *slot_ctx; | |
| int slot_state; | |
| int ret; | |
| /* If device is not setup, there is no point in resetting it */ | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); | |
| slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); | |
| if (slot_state != SLOT_STATE_DISABLED) | |
| return 0; | |
| cdnsp_queue_slot_control(pdev, TRB_ENABLE_SLOT); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| if (ret) | |
| goto show_trace; | |
| pdev->slot_id = 1; | |
| show_trace: | |
| trace_cdnsp_handle_cmd_enable_slot(cdnsp_get_slot_ctx(&pdev->out_ctx)); | |
| return ret; | |
| } | |
| /* | |
| * Issue an Address Device command with BSR=0 if setup is SETUP_CONTEXT_ONLY | |
| * or with BSR = 1 if set_address is SETUP_CONTEXT_ADDRESS. | |
| */ | |
| int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup) | |
| { | |
| struct cdnsp_input_control_ctx *ctrl_ctx; | |
| struct cdnsp_slot_ctx *slot_ctx; | |
| int dev_state = 0; | |
| int ret; | |
| if (!pdev->slot_id) { | |
| trace_cdnsp_slot_id("incorrect"); | |
| return -EINVAL; | |
| } | |
| if (!pdev->active_port->port_num) | |
| return -EINVAL; | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); | |
| dev_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); | |
| if (setup == SETUP_CONTEXT_ONLY && dev_state == SLOT_STATE_DEFAULT) { | |
| trace_cdnsp_slot_already_in_default(slot_ctx); | |
| return 0; | |
| } | |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); | |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); | |
| if (!slot_ctx->dev_info || dev_state == SLOT_STATE_DEFAULT) { | |
| ret = cdnsp_setup_addressable_priv_dev(pdev); | |
| if (ret) | |
| return ret; | |
| } | |
| cdnsp_copy_ep0_dequeue_into_input_ctx(pdev); | |
| ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG); | |
| ctrl_ctx->drop_flags = 0; | |
| trace_cdnsp_setup_device_slot(slot_ctx); | |
| cdnsp_queue_address_device(pdev, pdev->in_ctx.dma, setup); | |
| cdnsp_ring_cmd_db(pdev); | |
| ret = cdnsp_wait_for_cmd_compl(pdev); | |
| trace_cdnsp_handle_cmd_addr_dev(cdnsp_get_slot_ctx(&pdev->out_ctx)); | |
| /* Zero the input context control for later use. */ | |
| ctrl_ctx->add_flags = 0; | |
| ctrl_ctx->drop_flags = 0; | |
| return ret; | |
| } | |
| void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *pdev, | |
| struct usb_request *req, | |
| int enable) | |
| { | |
| if (pdev->active_port != &pdev->usb2_port || !pdev->gadget.lpm_capable) | |
| return; | |
| trace_cdnsp_lpm(enable); | |
| if (enable) | |
| writel(PORT_BESL(CDNSP_DEFAULT_BESL) | PORT_L1S_NYET | PORT_HLE, | |
| &pdev->active_port->regs->portpmsc); | |
| else | |
| writel(PORT_L1S_NYET, &pdev->active_port->regs->portpmsc); | |
| } | |
| static int cdnsp_get_frame(struct cdnsp_device *pdev) | |
| { | |
| return readl(&pdev->run_regs->microframe_index) >> 3; | |
| } | |
| static int cdnsp_gadget_ep_enable(struct usb_ep *ep, | |
| const struct usb_endpoint_descriptor *desc) | |
| { | |
| struct cdnsp_input_control_ctx *ctrl_ctx; | |
| struct cdnsp_device *pdev; | |
| struct cdnsp_ep *pep; | |
| unsigned long flags; | |
| u32 added_ctxs; | |
| int ret; | |
| if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT || | |
| !desc->wMaxPacketSize) | |
| return -EINVAL; | |
| pep = to_cdnsp_ep(ep); | |
| pdev = pep->pdev; | |
| pep->ep_state &= ~EP_UNCONFIGURED; | |
| if (dev_WARN_ONCE(pdev->dev, pep->ep_state & EP_ENABLED, | |
| "%s is already enabled\n", pep->name)) | |
| return 0; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| added_ctxs = cdnsp_get_endpoint_flag(desc); | |
| if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) { | |
| dev_err(pdev->dev, "ERROR: Bad endpoint number\n"); | |
| ret = -EINVAL; | |
| goto unlock; | |
| } | |
| pep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0; | |
| if (pdev->gadget.speed == USB_SPEED_FULL) { | |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT) | |
| pep->interval = desc->bInterval << 3; | |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) | |
| pep->interval = BIT(desc->bInterval - 1) << 3; | |
| } | |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) { | |
| if (pep->interval > BIT(12)) { | |
| dev_err(pdev->dev, "bInterval %d not supported\n", | |
| desc->bInterval); | |
| ret = -EINVAL; | |
| goto unlock; | |
| } | |
| cdnsp_set_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS); | |
| } | |
| ret = cdnsp_endpoint_init(pdev, pep, GFP_ATOMIC); | |
| if (ret) | |
| goto unlock; | |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); | |
| ctrl_ctx->add_flags = cpu_to_le32(added_ctxs); | |
| ctrl_ctx->drop_flags = 0; | |
| ret = cdnsp_update_eps_configuration(pdev, pep); | |
| if (ret) { | |
| cdnsp_free_endpoint_rings(pdev, pep); | |
| goto unlock; | |
| } | |
| pep->ep_state |= EP_ENABLED; | |
| pep->ep_state &= ~EP_STOPPED; | |
| unlock: | |
| trace_cdnsp_ep_enable_end(pep, 0); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static int cdnsp_gadget_ep_disable(struct usb_ep *ep) | |
| { | |
| struct cdnsp_input_control_ctx *ctrl_ctx; | |
| struct cdnsp_request *preq; | |
| struct cdnsp_device *pdev; | |
| struct cdnsp_ep *pep; | |
| unsigned long flags; | |
| u32 drop_flag; | |
| int ret = 0; | |
| if (!ep) | |
| return -EINVAL; | |
| pep = to_cdnsp_ep(ep); | |
| pdev = pep->pdev; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| if (!(pep->ep_state & EP_ENABLED)) { | |
| dev_err(pdev->dev, "%s is already disabled\n", pep->name); | |
| ret = -EINVAL; | |
| goto finish; | |
| } | |
| pep->ep_state |= EP_DIS_IN_RROGRESS; | |
| /* Endpoint was unconfigured by Reset Device command. */ | |
| if (!(pep->ep_state & EP_UNCONFIGURED)) | |
| cdnsp_cmd_stop_ep(pdev, pep); | |
| /* Remove all queued USB requests. */ | |
| while (!list_empty(&pep->pending_list)) { | |
| preq = next_request(&pep->pending_list); | |
| cdnsp_ep_dequeue(pep, preq); | |
| } | |
| cdnsp_invalidate_ep_events(pdev, pep); | |
| pep->ep_state &= ~EP_DIS_IN_RROGRESS; | |
| drop_flag = cdnsp_get_endpoint_flag(pep->endpoint.desc); | |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); | |
| ctrl_ctx->drop_flags = cpu_to_le32(drop_flag); | |
| ctrl_ctx->add_flags = 0; | |
| cdnsp_endpoint_zero(pdev, pep); | |
| if (!(pep->ep_state & EP_UNCONFIGURED)) | |
| ret = cdnsp_update_eps_configuration(pdev, pep); | |
| cdnsp_free_endpoint_rings(pdev, pep); | |
| pep->ep_state &= ~(EP_ENABLED | EP_UNCONFIGURED); | |
| pep->ep_state |= EP_STOPPED; | |
| finish: | |
| trace_cdnsp_ep_disable_end(pep, 0); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static struct usb_request *cdnsp_gadget_ep_alloc_request(struct usb_ep *ep, | |
| gfp_t gfp_flags) | |
| { | |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); | |
| struct cdnsp_request *preq; | |
| preq = kzalloc(sizeof(*preq), gfp_flags); | |
| if (!preq) | |
| return NULL; | |
| preq->epnum = pep->number; | |
| preq->pep = pep; | |
| trace_cdnsp_alloc_request(preq); | |
| return &preq->request; | |
| } | |
| static void cdnsp_gadget_ep_free_request(struct usb_ep *ep, | |
| struct usb_request *request) | |
| { | |
| struct cdnsp_request *preq = to_cdnsp_request(request); | |
| trace_cdnsp_free_request(preq); | |
| kfree(preq); | |
| } | |
| static int cdnsp_gadget_ep_queue(struct usb_ep *ep, | |
| struct usb_request *request, | |
| gfp_t gfp_flags) | |
| { | |
| struct cdnsp_request *preq; | |
| struct cdnsp_device *pdev; | |
| struct cdnsp_ep *pep; | |
| unsigned long flags; | |
| int ret; | |
| if (!request || !ep) | |
| return -EINVAL; | |
| pep = to_cdnsp_ep(ep); | |
| pdev = pep->pdev; | |
| if (!(pep->ep_state & EP_ENABLED)) { | |
| dev_err(pdev->dev, "%s: can't queue to disabled endpoint\n", | |
| pep->name); | |
| return -EINVAL; | |
| } | |
| preq = to_cdnsp_request(request); | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| ret = cdnsp_ep_enqueue(pep, preq); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static int cdnsp_gadget_ep_dequeue(struct usb_ep *ep, | |
| struct usb_request *request) | |
| { | |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); | |
| struct cdnsp_device *pdev = pep->pdev; | |
| unsigned long flags; | |
| int ret; | |
| if (request->status != -EINPROGRESS) | |
| return 0; | |
| if (!pep->endpoint.desc) { | |
| dev_err(pdev->dev, | |
| "%s: can't dequeue to disabled endpoint\n", | |
| pep->name); | |
| return -ESHUTDOWN; | |
| } | |
| /* Requests has been dequeued during disabling endpoint. */ | |
| if (!(pep->ep_state & EP_ENABLED)) | |
| return 0; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| ret = cdnsp_ep_dequeue(pep, to_cdnsp_request(request)); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static int cdnsp_gadget_ep_set_halt(struct usb_ep *ep, int value) | |
| { | |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); | |
| struct cdnsp_device *pdev = pep->pdev; | |
| struct cdnsp_request *preq; | |
| unsigned long flags; | |
| int ret; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| preq = next_request(&pep->pending_list); | |
| if (value) { | |
| if (preq) { | |
| trace_cdnsp_ep_busy_try_halt_again(pep, 0); | |
| ret = -EAGAIN; | |
| goto done; | |
| } | |
| } | |
| ret = cdnsp_halt_endpoint(pdev, pep, value); | |
| done: | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static int cdnsp_gadget_ep_set_wedge(struct usb_ep *ep) | |
| { | |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); | |
| struct cdnsp_device *pdev = pep->pdev; | |
| unsigned long flags; | |
| int ret; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| pep->ep_state |= EP_WEDGE; | |
| ret = cdnsp_halt_endpoint(pdev, pep, 1); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| static const struct usb_ep_ops cdnsp_gadget_ep0_ops = { | |
| .enable = cdnsp_gadget_ep_enable, | |
| .disable = cdnsp_gadget_ep_disable, | |
| .alloc_request = cdnsp_gadget_ep_alloc_request, | |
| .free_request = cdnsp_gadget_ep_free_request, | |
| .queue = cdnsp_gadget_ep_queue, | |
| .dequeue = cdnsp_gadget_ep_dequeue, | |
| .set_halt = cdnsp_gadget_ep_set_halt, | |
| .set_wedge = cdnsp_gadget_ep_set_wedge, | |
| }; | |
| static const struct usb_ep_ops cdnsp_gadget_ep_ops = { | |
| .enable = cdnsp_gadget_ep_enable, | |
| .disable = cdnsp_gadget_ep_disable, | |
| .alloc_request = cdnsp_gadget_ep_alloc_request, | |
| .free_request = cdnsp_gadget_ep_free_request, | |
| .queue = cdnsp_gadget_ep_queue, | |
| .dequeue = cdnsp_gadget_ep_dequeue, | |
| .set_halt = cdnsp_gadget_ep_set_halt, | |
| .set_wedge = cdnsp_gadget_ep_set_wedge, | |
| }; | |
| void cdnsp_gadget_giveback(struct cdnsp_ep *pep, | |
| struct cdnsp_request *preq, | |
| int status) | |
| { | |
| struct cdnsp_device *pdev = pep->pdev; | |
| list_del(&preq->list); | |
| if (preq->request.status == -EINPROGRESS) | |
| preq->request.status = status; | |
| usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request, | |
| preq->direction); | |
| trace_cdnsp_request_giveback(preq); | |
| if (preq != &pdev->ep0_preq) { | |
| spin_unlock(&pdev->lock); | |
| usb_gadget_giveback_request(&pep->endpoint, &preq->request); | |
| spin_lock(&pdev->lock); | |
| } | |
| } | |
| static struct usb_endpoint_descriptor cdnsp_gadget_ep0_desc = { | |
| .bLength = USB_DT_ENDPOINT_SIZE, | |
| .bDescriptorType = USB_DT_ENDPOINT, | |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, | |
| }; | |
| static int cdnsp_run(struct cdnsp_device *pdev, | |
| enum usb_device_speed speed) | |
| { | |
| u32 fs_speed = 0; | |
| u32 temp; | |
| int ret; | |
| temp = readl(&pdev->ir_set->irq_control); | |
| temp &= ~IMOD_INTERVAL_MASK; | |
| temp |= ((IMOD_DEFAULT_INTERVAL / 250) & IMOD_INTERVAL_MASK); | |
| writel(temp, &pdev->ir_set->irq_control); | |
| temp = readl(&pdev->port3x_regs->mode_addr); | |
| switch (speed) { | |
| case USB_SPEED_SUPER_PLUS: | |
| temp |= CFG_3XPORT_SSP_SUPPORT; | |
| break; | |
| case USB_SPEED_SUPER: | |
| temp &= ~CFG_3XPORT_SSP_SUPPORT; | |
| break; | |
| case USB_SPEED_HIGH: | |
| break; | |
| case USB_SPEED_FULL: | |
| fs_speed = PORT_REG6_FORCE_FS; | |
| break; | |
| default: | |
| dev_err(pdev->dev, "invalid maximum_speed parameter %d\n", | |
| speed); | |
| fallthrough; | |
| case USB_SPEED_UNKNOWN: | |
| /* Default to superspeed. */ | |
| speed = USB_SPEED_SUPER; | |
| break; | |
| } | |
| if (speed >= USB_SPEED_SUPER) { | |
| writel(temp, &pdev->port3x_regs->mode_addr); | |
| cdnsp_set_link_state(pdev, &pdev->usb3_port.regs->portsc, | |
| XDEV_RXDETECT); | |
| } else { | |
| cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc); | |
| } | |
| cdnsp_set_link_state(pdev, &pdev->usb2_port.regs->portsc, | |
| XDEV_RXDETECT); | |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512); | |
| writel(PORT_REG6_L1_L0_HW_EN | fs_speed, &pdev->port20_regs->port_reg6); | |
| ret = cdnsp_start(pdev); | |
| if (ret) { | |
| ret = -ENODEV; | |
| goto err; | |
| } | |
| temp = readl(&pdev->op_regs->command); | |
| temp |= (CMD_INTE); | |
| writel(temp, &pdev->op_regs->command); | |
| temp = readl(&pdev->ir_set->irq_pending); | |
| writel(IMAN_IE_SET(temp), &pdev->ir_set->irq_pending); | |
| trace_cdnsp_init("Controller ready to work"); | |
| return 0; | |
| err: | |
| cdnsp_halt(pdev); | |
| return ret; | |
| } | |
| static int cdnsp_gadget_udc_start(struct usb_gadget *g, | |
| struct usb_gadget_driver *driver) | |
| { | |
| enum usb_device_speed max_speed = driver->max_speed; | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); | |
| unsigned long flags; | |
| int ret; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| pdev->gadget_driver = driver; | |
| /* limit speed if necessary */ | |
| max_speed = min(driver->max_speed, g->max_speed); | |
| ret = cdnsp_run(pdev, max_speed); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| /* | |
| * Update Event Ring Dequeue Pointer: | |
| * - When all events have finished | |
| * - To avoid "Event Ring Full Error" condition | |
| */ | |
| void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev, | |
| union cdnsp_trb *event_ring_deq, | |
| u8 clear_ehb) | |
| { | |
| u64 temp_64; | |
| dma_addr_t deq; | |
| temp_64 = cdnsp_read_64(&pdev->ir_set->erst_dequeue); | |
| /* If necessary, update the HW's version of the event ring deq ptr. */ | |
| if (event_ring_deq != pdev->event_ring->dequeue) { | |
| deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg, | |
| pdev->event_ring->dequeue); | |
| temp_64 &= ERST_PTR_MASK; | |
| temp_64 |= ((u64)deq & (u64)~ERST_PTR_MASK); | |
| } | |
| /* Clear the event handler busy flag (RW1C). */ | |
| if (clear_ehb) | |
| temp_64 |= ERST_EHB; | |
| else | |
| temp_64 &= ~ERST_EHB; | |
| cdnsp_write_64(temp_64, &pdev->ir_set->erst_dequeue); | |
| } | |
| static void cdnsp_clear_cmd_ring(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_segment *seg; | |
| u64 val_64; | |
| int i; | |
| cdnsp_initialize_ring_info(pdev->cmd_ring); | |
| seg = pdev->cmd_ring->first_seg; | |
| for (i = 0; i < pdev->cmd_ring->num_segs; i++) { | |
| memset(seg->trbs, 0, | |
| sizeof(union cdnsp_trb) * (TRBS_PER_SEGMENT - 1)); | |
| seg = seg->next; | |
| } | |
| /* Set the address in the Command Ring Control register. */ | |
| val_64 = cdnsp_read_64(&pdev->op_regs->cmd_ring); | |
| val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) | | |
| (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) | | |
| pdev->cmd_ring->cycle_state; | |
| cdnsp_write_64(val_64, &pdev->op_regs->cmd_ring); | |
| } | |
| static void cdnsp_consume_all_events(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_segment *event_deq_seg; | |
| union cdnsp_trb *event_ring_deq; | |
| union cdnsp_trb *event; | |
| u32 cycle_bit; | |
| event_ring_deq = pdev->event_ring->dequeue; | |
| event_deq_seg = pdev->event_ring->deq_seg; | |
| event = pdev->event_ring->dequeue; | |
| /* Update ring dequeue pointer. */ | |
| while (1) { | |
| cycle_bit = (le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE); | |
| /* Does the controller or driver own the TRB? */ | |
| if (cycle_bit != pdev->event_ring->cycle_state) | |
| break; | |
| cdnsp_inc_deq(pdev, pdev->event_ring); | |
| if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) { | |
| event++; | |
| continue; | |
| } | |
| if (cdnsp_last_trb_on_ring(pdev->event_ring, event_deq_seg, | |
| event)) | |
| cycle_bit ^= 1; | |
| event_deq_seg = event_deq_seg->next; | |
| event = event_deq_seg->trbs; | |
| } | |
| cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1); | |
| } | |
| static void cdnsp_stop(struct cdnsp_device *pdev) | |
| { | |
| u32 temp; | |
| /* Remove internally queued request for ep0. */ | |
| if (!list_empty(&pdev->eps[0].pending_list)) { | |
| struct cdnsp_request *req; | |
| req = next_request(&pdev->eps[0].pending_list); | |
| if (req == &pdev->ep0_preq) | |
| cdnsp_ep_dequeue(&pdev->eps[0], req); | |
| } | |
| cdnsp_disable_port(pdev, &pdev->usb2_port.regs->portsc); | |
| cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc); | |
| cdnsp_disable_slot(pdev); | |
| cdnsp_halt(pdev); | |
| temp = readl(&pdev->op_regs->status); | |
| writel((temp & ~0x1fff) | STS_EINT, &pdev->op_regs->status); | |
| temp = readl(&pdev->ir_set->irq_pending); | |
| writel(IMAN_IE_CLEAR(temp), &pdev->ir_set->irq_pending); | |
| cdnsp_clear_port_change_bit(pdev, &pdev->usb2_port.regs->portsc); | |
| cdnsp_clear_port_change_bit(pdev, &pdev->usb3_port.regs->portsc); | |
| /* Clear interrupt line */ | |
| temp = readl(&pdev->ir_set->irq_pending); | |
| temp |= IMAN_IP; | |
| writel(temp, &pdev->ir_set->irq_pending); | |
| cdnsp_consume_all_events(pdev); | |
| cdnsp_clear_cmd_ring(pdev); | |
| trace_cdnsp_exit("Controller stopped."); | |
| } | |
| /* | |
| * Stop controller. | |
| * This function is called by the gadget core when the driver is removed. | |
| * Disable slot, disable IRQs, and quiesce the controller. | |
| */ | |
| static int cdnsp_gadget_udc_stop(struct usb_gadget *g) | |
| { | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); | |
| unsigned long flags; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| cdnsp_stop(pdev); | |
| pdev->gadget_driver = NULL; | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return 0; | |
| } | |
| static int cdnsp_gadget_get_frame(struct usb_gadget *g) | |
| { | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); | |
| return cdnsp_get_frame(pdev); | |
| } | |
| static void __cdnsp_gadget_wakeup(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_port_regs __iomem *port_regs; | |
| u32 portpm, portsc; | |
| port_regs = pdev->active_port->regs; | |
| portsc = readl(&port_regs->portsc) & PORT_PLS_MASK; | |
| /* Remote wakeup feature is not enabled by host. */ | |
| if (pdev->gadget.speed < USB_SPEED_SUPER && portsc == XDEV_U2) { | |
| portpm = readl(&port_regs->portpmsc); | |
| if (!(portpm & PORT_RWE)) | |
| return; | |
| } | |
| if (portsc == XDEV_U3 && !pdev->may_wakeup) | |
| return; | |
| cdnsp_set_link_state(pdev, &port_regs->portsc, XDEV_U0); | |
| pdev->cdnsp_state |= CDNSP_WAKEUP_PENDING; | |
| } | |
| static int cdnsp_gadget_wakeup(struct usb_gadget *g) | |
| { | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); | |
| unsigned long flags; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| __cdnsp_gadget_wakeup(pdev); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return 0; | |
| } | |
| static int cdnsp_gadget_set_selfpowered(struct usb_gadget *g, | |
| int is_selfpowered) | |
| { | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); | |
| unsigned long flags; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| g->is_selfpowered = !!is_selfpowered; | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return 0; | |
| } | |
| static int cdnsp_gadget_pullup(struct usb_gadget *gadget, int is_on) | |
| { | |
| struct cdnsp_device *pdev = gadget_to_cdnsp(gadget); | |
| struct cdns *cdns = dev_get_drvdata(pdev->dev); | |
| unsigned long flags; | |
| trace_cdnsp_pullup(is_on); | |
| /* | |
| * Disable events handling while controller is being | |
| * enabled/disabled. | |
| */ | |
| disable_irq(cdns->dev_irq); | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| if (!is_on) { | |
| cdnsp_reset_device(pdev); | |
| cdns_clear_vbus(cdns); | |
| } else { | |
| cdns_set_vbus(cdns); | |
| } | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| enable_irq(cdns->dev_irq); | |
| return 0; | |
| } | |
| static const struct usb_gadget_ops cdnsp_gadget_ops = { | |
| .get_frame = cdnsp_gadget_get_frame, | |
| .wakeup = cdnsp_gadget_wakeup, | |
| .set_selfpowered = cdnsp_gadget_set_selfpowered, | |
| .pullup = cdnsp_gadget_pullup, | |
| .udc_start = cdnsp_gadget_udc_start, | |
| .udc_stop = cdnsp_gadget_udc_stop, | |
| }; | |
| static void cdnsp_get_ep_buffering(struct cdnsp_device *pdev, | |
| struct cdnsp_ep *pep) | |
| { | |
| void __iomem *reg = &pdev->cap_regs->hc_capbase; | |
| int endpoints; | |
| reg += cdnsp_find_next_ext_cap(reg, 0, XBUF_CAP_ID); | |
| if (!pep->direction) { | |
| pep->buffering = readl(reg + XBUF_RX_TAG_MASK_0_OFFSET); | |
| pep->buffering_period = readl(reg + XBUF_RX_TAG_MASK_1_OFFSET); | |
| pep->buffering = (pep->buffering + 1) / 2; | |
| pep->buffering_period = (pep->buffering_period + 1) / 2; | |
| return; | |
| } | |
| endpoints = HCS_ENDPOINTS(pdev->hcs_params1) / 2; | |
| /* Set to XBUF_TX_TAG_MASK_0 register. */ | |
| reg += XBUF_TX_CMD_OFFSET + (endpoints * 2 + 2) * sizeof(u32); | |
| /* Set reg to XBUF_TX_TAG_MASK_N related with this endpoint. */ | |
| reg += pep->number * sizeof(u32) * 2; | |
| pep->buffering = (readl(reg) + 1) / 2; | |
| pep->buffering_period = pep->buffering; | |
| } | |
| static int cdnsp_gadget_init_endpoints(struct cdnsp_device *pdev) | |
| { | |
| int max_streams = HCC_MAX_PSA(pdev->hcc_params); | |
| struct cdnsp_ep *pep; | |
| int i; | |
| INIT_LIST_HEAD(&pdev->gadget.ep_list); | |
| if (max_streams < STREAM_LOG_STREAMS) { | |
| dev_err(pdev->dev, "Stream size %d not supported\n", | |
| max_streams); | |
| return -EINVAL; | |
| } | |
| max_streams = STREAM_LOG_STREAMS; | |
| for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) { | |
| bool direction = !(i & 1); /* Start from OUT endpoint. */ | |
| u8 epnum = ((i + 1) >> 1); | |
| if (!CDNSP_IF_EP_EXIST(pdev, epnum, direction)) | |
| continue; | |
| pep = &pdev->eps[i]; | |
| pep->pdev = pdev; | |
| pep->number = epnum; | |
| pep->direction = direction; /* 0 for OUT, 1 for IN. */ | |
| /* | |
| * Ep0 is bidirectional, so ep0in and ep0out are represented by | |
| * pdev->eps[0] | |
| */ | |
| if (epnum == 0) { | |
| snprintf(pep->name, sizeof(pep->name), "ep%d%s", | |
| epnum, "BiDir"); | |
| pep->idx = 0; | |
| usb_ep_set_maxpacket_limit(&pep->endpoint, 512); | |
| pep->endpoint.maxburst = 1; | |
| pep->endpoint.ops = &cdnsp_gadget_ep0_ops; | |
| pep->endpoint.desc = &cdnsp_gadget_ep0_desc; | |
| pep->endpoint.comp_desc = NULL; | |
| pep->endpoint.caps.type_control = true; | |
| pep->endpoint.caps.dir_in = true; | |
| pep->endpoint.caps.dir_out = true; | |
| pdev->ep0_preq.epnum = pep->number; | |
| pdev->ep0_preq.pep = pep; | |
| pdev->gadget.ep0 = &pep->endpoint; | |
| } else { | |
| snprintf(pep->name, sizeof(pep->name), "ep%d%s", | |
| epnum, (pep->direction) ? "in" : "out"); | |
| pep->idx = (epnum * 2 + (direction ? 1 : 0)) - 1; | |
| usb_ep_set_maxpacket_limit(&pep->endpoint, 1024); | |
| pep->endpoint.max_streams = max_streams; | |
| pep->endpoint.ops = &cdnsp_gadget_ep_ops; | |
| list_add_tail(&pep->endpoint.ep_list, | |
| &pdev->gadget.ep_list); | |
| pep->endpoint.caps.type_iso = true; | |
| pep->endpoint.caps.type_bulk = true; | |
| pep->endpoint.caps.type_int = true; | |
| pep->endpoint.caps.dir_in = direction; | |
| pep->endpoint.caps.dir_out = !direction; | |
| } | |
| pep->endpoint.name = pep->name; | |
| pep->in_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, pep->idx); | |
| pep->out_ctx = cdnsp_get_ep_ctx(&pdev->out_ctx, pep->idx); | |
| cdnsp_get_ep_buffering(pdev, pep); | |
| dev_dbg(pdev->dev, "Init %s, MPS: %04x SupType: " | |
| "CTRL: %s, INT: %s, BULK: %s, ISOC %s, " | |
| "SupDir IN: %s, OUT: %s\n", | |
| pep->name, 1024, | |
| (pep->endpoint.caps.type_control) ? "yes" : "no", | |
| (pep->endpoint.caps.type_int) ? "yes" : "no", | |
| (pep->endpoint.caps.type_bulk) ? "yes" : "no", | |
| (pep->endpoint.caps.type_iso) ? "yes" : "no", | |
| (pep->endpoint.caps.dir_in) ? "yes" : "no", | |
| (pep->endpoint.caps.dir_out) ? "yes" : "no"); | |
| INIT_LIST_HEAD(&pep->pending_list); | |
| } | |
| return 0; | |
| } | |
| static void cdnsp_gadget_free_endpoints(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_ep *pep; | |
| int i; | |
| for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) { | |
| pep = &pdev->eps[i]; | |
| if (pep->number != 0 && pep->out_ctx) | |
| list_del(&pep->endpoint.ep_list); | |
| } | |
| } | |
| void cdnsp_disconnect_gadget(struct cdnsp_device *pdev) | |
| { | |
| pdev->cdnsp_state |= CDNSP_STATE_DISCONNECT_PENDING; | |
| if (pdev->gadget_driver && pdev->gadget_driver->disconnect) { | |
| spin_unlock(&pdev->lock); | |
| pdev->gadget_driver->disconnect(&pdev->gadget); | |
| spin_lock(&pdev->lock); | |
| } | |
| pdev->gadget.speed = USB_SPEED_UNKNOWN; | |
| usb_gadget_set_state(&pdev->gadget, USB_STATE_NOTATTACHED); | |
| pdev->cdnsp_state &= ~CDNSP_STATE_DISCONNECT_PENDING; | |
| } | |
| void cdnsp_suspend_gadget(struct cdnsp_device *pdev) | |
| { | |
| if (pdev->gadget_driver && pdev->gadget_driver->suspend) { | |
| spin_unlock(&pdev->lock); | |
| pdev->gadget_driver->suspend(&pdev->gadget); | |
| spin_lock(&pdev->lock); | |
| } | |
| } | |
| void cdnsp_resume_gadget(struct cdnsp_device *pdev) | |
| { | |
| if (pdev->gadget_driver && pdev->gadget_driver->resume) { | |
| spin_unlock(&pdev->lock); | |
| pdev->gadget_driver->resume(&pdev->gadget); | |
| spin_lock(&pdev->lock); | |
| } | |
| } | |
| void cdnsp_irq_reset(struct cdnsp_device *pdev) | |
| { | |
| struct cdnsp_port_regs __iomem *port_regs; | |
| cdnsp_reset_device(pdev); | |
| port_regs = pdev->active_port->regs; | |
| pdev->gadget.speed = cdnsp_port_speed(readl(port_regs)); | |
| spin_unlock(&pdev->lock); | |
| usb_gadget_udc_reset(&pdev->gadget, pdev->gadget_driver); | |
| spin_lock(&pdev->lock); | |
| switch (pdev->gadget.speed) { | |
| case USB_SPEED_SUPER_PLUS: | |
| case USB_SPEED_SUPER: | |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512); | |
| pdev->gadget.ep0->maxpacket = 512; | |
| break; | |
| case USB_SPEED_HIGH: | |
| case USB_SPEED_FULL: | |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64); | |
| pdev->gadget.ep0->maxpacket = 64; | |
| break; | |
| default: | |
| /* Low speed is not supported. */ | |
| dev_err(pdev->dev, "Unknown device speed\n"); | |
| break; | |
| } | |
| cdnsp_clear_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS); | |
| cdnsp_setup_device(pdev, SETUP_CONTEXT_ONLY); | |
| usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT); | |
| } | |
| static void cdnsp_get_rev_cap(struct cdnsp_device *pdev) | |
| { | |
| void __iomem *reg = &pdev->cap_regs->hc_capbase; | |
| reg += cdnsp_find_next_ext_cap(reg, 0, RTL_REV_CAP); | |
| pdev->rev_cap = reg; | |
| dev_info(pdev->dev, "Rev: %08x/%08x, eps: %08x, buff: %08x/%08x\n", | |
| readl(&pdev->rev_cap->ctrl_revision), | |
| readl(&pdev->rev_cap->rtl_revision), | |
| readl(&pdev->rev_cap->ep_supported), | |
| readl(&pdev->rev_cap->rx_buff_size), | |
| readl(&pdev->rev_cap->tx_buff_size)); | |
| } | |
| static int cdnsp_gen_setup(struct cdnsp_device *pdev) | |
| { | |
| int ret; | |
| u32 reg; | |
| pdev->cap_regs = pdev->regs; | |
| pdev->op_regs = pdev->regs + | |
| HC_LENGTH(readl(&pdev->cap_regs->hc_capbase)); | |
| pdev->run_regs = pdev->regs + | |
| (readl(&pdev->cap_regs->run_regs_off) & RTSOFF_MASK); | |
| /* Cache read-only capability registers */ | |
| pdev->hcs_params1 = readl(&pdev->cap_regs->hcs_params1); | |
| pdev->hcc_params = readl(&pdev->cap_regs->hc_capbase); | |
| pdev->hci_version = HC_VERSION(pdev->hcc_params); | |
| pdev->hcc_params = readl(&pdev->cap_regs->hcc_params); | |
| cdnsp_get_rev_cap(pdev); | |
| /* Make sure the Device Controller is halted. */ | |
| ret = cdnsp_halt(pdev); | |
| if (ret) | |
| return ret; | |
| /* Reset the internal controller memory state and registers. */ | |
| ret = cdnsp_reset(pdev); | |
| if (ret) | |
| return ret; | |
| /* | |
| * Set dma_mask and coherent_dma_mask to 64-bits, | |
| * if controller supports 64-bit addressing. | |
| */ | |
| if (HCC_64BIT_ADDR(pdev->hcc_params) && | |
| !dma_set_mask(pdev->dev, DMA_BIT_MASK(64))) { | |
| dev_dbg(pdev->dev, "Enabling 64-bit DMA addresses.\n"); | |
| dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(64)); | |
| } else { | |
| /* | |
| * This is to avoid error in cases where a 32-bit USB | |
| * controller is used on a 64-bit capable system. | |
| */ | |
| ret = dma_set_mask(pdev->dev, DMA_BIT_MASK(32)); | |
| if (ret) | |
| return ret; | |
| dev_dbg(pdev->dev, "Enabling 32-bit DMA addresses.\n"); | |
| dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(32)); | |
| } | |
| spin_lock_init(&pdev->lock); | |
| ret = cdnsp_mem_init(pdev); | |
| if (ret) | |
| return ret; | |
| /* | |
| * Software workaround for U1: after transition | |
| * to U1 the controller starts gating clock, and in some cases, | |
| * it causes that controller stack. | |
| */ | |
| reg = readl(&pdev->port3x_regs->mode_2); | |
| reg &= ~CFG_3XPORT_U1_PIPE_CLK_GATE_EN; | |
| writel(reg, &pdev->port3x_regs->mode_2); | |
| return 0; | |
| } | |
| static int __cdnsp_gadget_init(struct cdns *cdns) | |
| { | |
| struct cdnsp_device *pdev; | |
| u32 max_speed; | |
| int ret = -ENOMEM; | |
| cdns_drd_gadget_on(cdns); | |
| pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); | |
| if (!pdev) | |
| return -ENOMEM; | |
| pm_runtime_get_sync(cdns->dev); | |
| cdns->gadget_dev = pdev; | |
| pdev->dev = cdns->dev; | |
| pdev->regs = cdns->dev_regs; | |
| max_speed = usb_get_maximum_speed(cdns->dev); | |
| switch (max_speed) { | |
| case USB_SPEED_FULL: | |
| case USB_SPEED_HIGH: | |
| case USB_SPEED_SUPER: | |
| case USB_SPEED_SUPER_PLUS: | |
| break; | |
| default: | |
| dev_err(cdns->dev, "invalid speed parameter %d\n", max_speed); | |
| fallthrough; | |
| case USB_SPEED_UNKNOWN: | |
| /* Default to SSP */ | |
| max_speed = USB_SPEED_SUPER_PLUS; | |
| break; | |
| } | |
| pdev->gadget.ops = &cdnsp_gadget_ops; | |
| pdev->gadget.name = "cdnsp-gadget"; | |
| pdev->gadget.speed = USB_SPEED_UNKNOWN; | |
| pdev->gadget.sg_supported = 1; | |
| pdev->gadget.max_speed = max_speed; | |
| pdev->gadget.lpm_capable = 1; | |
| pdev->setup_buf = kzalloc(CDNSP_EP0_SETUP_SIZE, GFP_KERNEL); | |
| if (!pdev->setup_buf) | |
| goto free_pdev; | |
| /* | |
| * Controller supports not aligned buffer but it should improve | |
| * performance. | |
| */ | |
| pdev->gadget.quirk_ep_out_aligned_size = true; | |
| ret = cdnsp_gen_setup(pdev); | |
| if (ret) { | |
| dev_err(pdev->dev, "Generic initialization failed %d\n", ret); | |
| goto free_setup; | |
| } | |
| ret = cdnsp_gadget_init_endpoints(pdev); | |
| if (ret) { | |
| dev_err(pdev->dev, "failed to initialize endpoints\n"); | |
| goto halt_pdev; | |
| } | |
| ret = usb_add_gadget_udc(pdev->dev, &pdev->gadget); | |
| if (ret) { | |
| dev_err(pdev->dev, "failed to register udc\n"); | |
| goto free_endpoints; | |
| } | |
| ret = devm_request_threaded_irq(pdev->dev, cdns->dev_irq, | |
| cdnsp_irq_handler, | |
| cdnsp_thread_irq_handler, IRQF_SHARED, | |
| dev_name(pdev->dev), pdev); | |
| if (ret) | |
| goto del_gadget; | |
| return 0; | |
| del_gadget: | |
| usb_del_gadget_udc(&pdev->gadget); | |
| free_endpoints: | |
| cdnsp_gadget_free_endpoints(pdev); | |
| halt_pdev: | |
| cdnsp_halt(pdev); | |
| cdnsp_reset(pdev); | |
| cdnsp_mem_cleanup(pdev); | |
| free_setup: | |
| kfree(pdev->setup_buf); | |
| free_pdev: | |
| kfree(pdev); | |
| return ret; | |
| } | |
| static void cdnsp_gadget_exit(struct cdns *cdns) | |
| { | |
| struct cdnsp_device *pdev = cdns->gadget_dev; | |
| devm_free_irq(pdev->dev, cdns->dev_irq, pdev); | |
| pm_runtime_mark_last_busy(cdns->dev); | |
| pm_runtime_put_autosuspend(cdns->dev); | |
| usb_del_gadget_udc(&pdev->gadget); | |
| cdnsp_gadget_free_endpoints(pdev); | |
| cdnsp_mem_cleanup(pdev); | |
| kfree(pdev); | |
| cdns->gadget_dev = NULL; | |
| cdns_drd_gadget_off(cdns); | |
| } | |
| static int cdnsp_gadget_suspend(struct cdns *cdns, bool do_wakeup) | |
| { | |
| struct cdnsp_device *pdev = cdns->gadget_dev; | |
| unsigned long flags; | |
| if (pdev->link_state == XDEV_U3) | |
| return 0; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| cdnsp_disconnect_gadget(pdev); | |
| cdnsp_stop(pdev); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return 0; | |
| } | |
| static int cdnsp_gadget_resume(struct cdns *cdns, bool hibernated) | |
| { | |
| struct cdnsp_device *pdev = cdns->gadget_dev; | |
| enum usb_device_speed max_speed; | |
| unsigned long flags; | |
| int ret; | |
| if (!pdev->gadget_driver) | |
| return 0; | |
| spin_lock_irqsave(&pdev->lock, flags); | |
| max_speed = pdev->gadget_driver->max_speed; | |
| /* Limit speed if necessary. */ | |
| max_speed = min(max_speed, pdev->gadget.max_speed); | |
| ret = cdnsp_run(pdev, max_speed); | |
| if (pdev->link_state == XDEV_U3) | |
| __cdnsp_gadget_wakeup(pdev); | |
| spin_unlock_irqrestore(&pdev->lock, flags); | |
| return ret; | |
| } | |
| /** | |
| * cdnsp_gadget_init - initialize device structure | |
| * @cdns: cdnsp instance | |
| * | |
| * This function initializes the gadget. | |
| */ | |
| int cdnsp_gadget_init(struct cdns *cdns) | |
| { | |
| struct cdns_role_driver *rdrv; | |
| rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL); | |
| if (!rdrv) | |
| return -ENOMEM; | |
| rdrv->start = __cdnsp_gadget_init; | |
| rdrv->stop = cdnsp_gadget_exit; | |
| rdrv->suspend = cdnsp_gadget_suspend; | |
| rdrv->resume = cdnsp_gadget_resume; | |
| rdrv->state = CDNS_ROLE_STATE_INACTIVE; | |
| rdrv->name = "gadget"; | |
| cdns->roles[USB_ROLE_DEVICE] = rdrv; | |
| return 0; | |
| } |