Documentation/admin-guide/media/mgb4.rst - linux/kernel/git/dhowells/linux-fs - Git at Google

 .. SPDX-License-Identifier: GPL-2.0

 ====================
 mgb4 sysfs interface
 ====================

 The mgb4 driver provides a sysfs interface, that is used to configure video
 stream related parameters (some of them must be set properly before the v4l2
 device can be opened) and obtain the video device/stream status.

 There are two types of parameters - global / PCI card related, found under
 ``/sys/class/video4linux/videoX/device`` and module specific found under
 ``/sys/class/video4linux/videoX``.


 Global (PCI card) parameters
 ============================

 **module_type** (R):
     Module type.

     | 0 - No module present
     | 1 - FPDL3
     | 2 - GMSL

 **module_version** (R):
     Module version number. Zero in case of a missing module.

 **fw_type** (R):
     Firmware type.

     | 1 - FPDL3
     | 2 - GMSL

 **fw_version** (R):
     Firmware version number.

 **serial_number** (R):
     Card serial number. The format is::

         PRODUCT-REVISION-SERIES-SERIAL

     where each component is a 8b number.


 Common FPDL3/GMSL input parameters
 ==================================

 **input_id** (R):
     Input number ID, zero based.

 **oldi_lane_width** (RW):
     Number of deserializer output lanes.

     | 0 - single
     | 1 - dual (default)

 **color_mapping** (RW):
     Mapping of the incoming bits in the signal to the colour bits of the pixels.

     | 0 - OLDI/JEIDA
     | 1 - SPWG/VESA (default)

 **link_status** (R):
     Video link status. If the link is locked, chips are properly connected and
     communicating at the same speed and protocol. The link can be locked without
     an active video stream.

     A value of 0 is equivalent to the V4L2_IN_ST_NO_SYNC flag of the V4L2
     VIDIOC_ENUMINPUT status bits.

     | 0 - unlocked
     | 1 - locked

 **stream_status** (R):
     Video stream status. A stream is detected if the link is locked, the input
     pixel clock is running and the DE signal is moving.

     A value of 0 is equivalent to the V4L2_IN_ST_NO_SIGNAL flag of the V4L2
     VIDIOC_ENUMINPUT status bits.

     | 0 - not detected
     | 1 - detected

 **video_width** (R):
     Video stream width. This is the actual width as detected by the HW.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the width
     field of the v4l2_bt_timings struct.

 **video_height** (R):
     Video stream height. This is the actual height as detected by the HW.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the height
     field of the v4l2_bt_timings struct.

 **vsync_status** (R):
     The type of VSYNC pulses as detected by the video format detector.

     The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
     the polarities field of the v4l2_bt_timings struct.

     | 0 - active low
     | 1 - active high
     | 2 - not available

 **hsync_status** (R):
     The type of HSYNC pulses as detected by the video format detector.

     The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
     the polarities field of the v4l2_bt_timings struct.

     | 0 - active low
     | 1 - active high
     | 2 - not available

 **vsync_gap_length** (RW):
     If the incoming video signal does not contain synchronization VSYNC and
     HSYNC pulses, these must be generated internally in the FPGA to achieve
     the correct frame ordering. This value indicates, how many "empty" pixels
     (pixels with deasserted Data Enable signal) are necessary to generate the
     internal VSYNC pulse.

 **hsync_gap_length** (RW):
     If the incoming video signal does not contain synchronization VSYNC and
     HSYNC pulses, these must be generated internally in the FPGA to achieve
     the correct frame ordering. This value indicates, how many "empty" pixels
     (pixels with deasserted Data Enable signal) are necessary to generate the
     internal HSYNC pulse. The value must be greater than 1 and smaller than
     vsync_gap_length.

 **pclk_frequency** (R):
     Input pixel clock frequency in kHz.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the pixelclock field of the v4l2_bt_timings struct.

     *Note: The frequency_range parameter must be set properly first to get
     a valid frequency here.*

 **hsync_width** (R):
     Width of the HSYNC signal in PCLK clock ticks.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the hsync field of the v4l2_bt_timings struct.

 **vsync_width** (R):
     Width of the VSYNC signal in PCLK clock ticks.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the vsync field of the v4l2_bt_timings struct.

 **hback_porch** (R):
     Number of PCLK pulses between deassertion of the HSYNC signal and the first
     valid pixel in the video line (marked by DE=1).

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the hbackporch field of the v4l2_bt_timings struct.

 **hfront_porch** (R):
     Number of PCLK pulses between the end of the last valid pixel in the video
     line (marked by DE=1) and assertion of the HSYNC signal.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the hfrontporch field of the v4l2_bt_timings struct.

 **vback_porch** (R):
     Number of video lines between deassertion of the VSYNC signal and the video
     line with the first valid pixel (marked by DE=1).

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the vbackporch field of the v4l2_bt_timings struct.

 **vfront_porch** (R):
     Number of video lines between the end of the last valid pixel line (marked
     by DE=1) and assertion of the VSYNC signal.

     The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
     the vfrontporch field of the v4l2_bt_timings struct.

 **frequency_range** (RW)
     PLL frequency range of the OLDI input clock generator. The PLL frequency is
     derived from the Pixel Clock Frequency (PCLK) and is equal to PCLK if
     oldi_lane_width is set to "single" and PCLK/2 if oldi_lane_width is set to
     "dual".

     | 0 - PLL < 50MHz (default)
     | 1 - PLL >= 50MHz

     *Note: This parameter can not be changed while the input v4l2 device is
     open.*


 Common FPDL3/GMSL output parameters
 ===================================

 **output_id** (R):
     Output number ID, zero based.

 **video_source** (RW):
     Output video source. If set to 0 or 1, the source is the corresponding card
     input and the v4l2 output devices are disabled. If set to 2 or 3, the source
     is the corresponding v4l2 video output device. The default is
     the corresponding v4l2 output, i.e. 2 for OUT1 and 3 for OUT2.

     | 0 - input 0
     | 1 - input 1
     | 2 - v4l2 output 0
     | 3 - v4l2 output 1

     *Note: This parameter can not be changed while ANY of the input/output v4l2
     devices is open.*

 **display_width** (RW):
     Display width. There is no autodetection of the connected display, so the
     proper value must be set before the start of streaming. The default width
     is 1280.

     *Note: This parameter can not be changed while the output v4l2 device is
     open.*

 **display_height** (RW):
     Display height. There is no autodetection of the connected display, so the
     proper value must be set before the start of streaming. The default height
     is 640.

     *Note: This parameter can not be changed while the output v4l2 device is
     open.*

 **frame_rate** (RW):
     Output video frame rate in frames per second. The default frame rate is
     60Hz.

 **hsync_polarity** (RW):
     HSYNC signal polarity.

     | 0 - active low (default)
     | 1 - active high

 **vsync_polarity** (RW):
     VSYNC signal polarity.

     | 0 - active low (default)
     | 1 - active high

 **de_polarity** (RW):
     DE signal polarity.

     | 0 - active low
     | 1 - active high (default)

 **pclk_frequency** (RW):
     Output pixel clock frequency. Allowed values are between 25000-190000(kHz)
     and there is a non-linear stepping between two consecutive allowed
     frequencies. The driver finds the nearest allowed frequency to the given
     value and sets it. When reading this property, you get the exact
     frequency set by the driver. The default frequency is 70000kHz.

     *Note: This parameter can not be changed while the output v4l2 device is
     open.*

 **hsync_width** (RW):
     Width of the HSYNC signal in pixels. The default value is 16.

 **vsync_width** (RW):
     Width of the VSYNC signal in video lines. The default value is 2.

 **hback_porch** (RW):
     Number of PCLK pulses between deassertion of the HSYNC signal and the first
     valid pixel in the video line (marked by DE=1). The default value is 32.

 **hfront_porch** (RW):
     Number of PCLK pulses between the end of the last valid pixel in the video
     line (marked by DE=1) and assertion of the HSYNC signal. The default value
     is 32.

 **vback_porch** (RW):
     Number of video lines between deassertion of the VSYNC signal and the video
     line with the first valid pixel (marked by DE=1). The default value is 2.

 **vfront_porch** (RW):
     Number of video lines between the end of the last valid pixel line (marked
     by DE=1) and assertion of the VSYNC signal. The default value is 2.


 FPDL3 specific input parameters
 ===============================

 **fpdl3_input_width** (RW):
     Number of deserializer input lines.

     | 0 - auto (default)
     | 1 - single
     | 2 - dual

 FPDL3 specific output parameters
 ================================

 **fpdl3_output_width** (RW):
     Number of serializer output lines.

     | 0 - auto (default)
     | 1 - single
     | 2 - dual

 GMSL specific input parameters
 ==============================

 **gmsl_mode** (RW):
     GMSL speed mode.

     | 0 - 12Gb/s (default)
     | 1 - 6Gb/s
     | 2 - 3Gb/s
     | 3 - 1.5Gb/s

 **gmsl_stream_id** (RW):
     The GMSL multi-stream contains up to four video streams. This parameter
     selects which stream is captured by the video input. The value is the
     zero-based index of the stream. The default stream id is 0.

     *Note: This parameter can not be changed while the input v4l2 device is
     open.*

 **gmsl_fec** (RW):
     GMSL Forward Error Correction (FEC).

     | 0 - disabled
     | 1 - enabled (default)


 ====================
 mgb4 mtd partitions
 ====================

 The mgb4 driver creates a MTD device with two partitions:
  - mgb4-fw.X - FPGA firmware.
  - mgb4-data.X - Factory settings, e.g. card serial number.

 The *mgb4-fw* partition is writable and is used for FW updates, *mgb4-data* is
 read-only. The *X* attached to the partition name represents the card number.
 Depending on the CONFIG_MTD_PARTITIONED_MASTER kernel configuration, you may
 also have a third partition named *mgb4-flash* available in the system. This
 partition represents the whole, unpartitioned, card's FLASH memory and one should
 not fiddle with it...

 ====================
 mgb4 iio (triggers)
 ====================

 The mgb4 driver creates an Industrial I/O (IIO) device that provides trigger and
 signal level status capability. The following scan elements are available:

 **activity**:
 	The trigger levels and pending status.

 	| bit 1 - trigger 1 pending
 	| bit 2 - trigger 2 pending
 	| bit 5 - trigger 1 level
 	| bit 6 - trigger 2 level

 **timestamp**:
 	The trigger event timestamp.

 The iio device can operate either in "raw" mode where you can fetch the signal
 levels (activity bits 5 and 6) using sysfs access or in triggered buffer mode.
 In the triggered buffer mode you can follow the signal level changes (activity
 bits 1 and 2) using the iio device in /dev. If you enable the timestamps, you
 will also get the exact trigger event time that can be matched to a video frame
 (every mgb4 video frame has a timestamp with the same clock source).

 *Note: although the activity sample always contains all the status bits, it makes
 no sense to get the pending bits in raw mode or the level bits in the triggered
 buffer mode - the values do not represent valid data in such case.*
	.. SPDX-License-Identifier: GPL-2.0

	====================
	mgb4 sysfs interface
	====================

	The mgb4 driver provides a sysfs interface, that is used to configure video
	stream related parameters (some of them must be set properly before the v4l2
	device can be opened) and obtain the video device/stream status.

	There are two types of parameters - global / PCI card related, found under
	``/sys/class/video4linux/videoX/device`` and module specific found under
	``/sys/class/video4linux/videoX``.


	Global (PCI card) parameters
	============================

	module_type (R):
	Module type.

	\| 0 - No module present
	\| 1 - FPDL3
	\| 2 - GMSL

	module_version (R):
	Module version number. Zero in case of a missing module.

	fw_type (R):
	Firmware type.

	\| 1 - FPDL3
	\| 2 - GMSL

	fw_version (R):
	Firmware version number.

	serial_number (R):
	Card serial number. The format is::

	PRODUCT-REVISION-SERIES-SERIAL

	where each component is a 8b number.


	Common FPDL3/GMSL input parameters
	==================================

	input_id (R):
	Input number ID, zero based.

	oldi_lane_width (RW):
	Number of deserializer output lanes.

	\| 0 - single
	\| 1 - dual (default)

	color_mapping (RW):
	Mapping of the incoming bits in the signal to the colour bits of the pixels.

	\| 0 - OLDI/JEIDA
	\| 1 - SPWG/VESA (default)

	link_status (R):
	Video link status. If the link is locked, chips are properly connected and
	communicating at the same speed and protocol. The link can be locked without
	an active video stream.

	A value of 0 is equivalent to the V4L2_IN_ST_NO_SYNC flag of the V4L2
	VIDIOC_ENUMINPUT status bits.

	\| 0 - unlocked
	\| 1 - locked

	stream_status (R):
	Video stream status. A stream is detected if the link is locked, the input
	pixel clock is running and the DE signal is moving.

	A value of 0 is equivalent to the V4L2_IN_ST_NO_SIGNAL flag of the V4L2
	VIDIOC_ENUMINPUT status bits.

	\| 0 - not detected
	\| 1 - detected

	video_width (R):
	Video stream width. This is the actual width as detected by the HW.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the width
	field of the v4l2_bt_timings struct.

	video_height (R):
	Video stream height. This is the actual height as detected by the HW.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the height
	field of the v4l2_bt_timings struct.

	vsync_status (R):
	The type of VSYNC pulses as detected by the video format detector.

	The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
	the polarities field of the v4l2_bt_timings struct.

	\| 0 - active low
	\| 1 - active high
	\| 2 - not available

	hsync_status (R):
	The type of HSYNC pulses as detected by the video format detector.

	The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
	the polarities field of the v4l2_bt_timings struct.

	\| 0 - active low
	\| 1 - active high
	\| 2 - not available

	vsync_gap_length (RW):
	If the incoming video signal does not contain synchronization VSYNC and
	HSYNC pulses, these must be generated internally in the FPGA to achieve
	the correct frame ordering. This value indicates, how many "empty" pixels
	(pixels with deasserted Data Enable signal) are necessary to generate the
	internal VSYNC pulse.

	hsync_gap_length (RW):
	If the incoming video signal does not contain synchronization VSYNC and
	HSYNC pulses, these must be generated internally in the FPGA to achieve
	the correct frame ordering. This value indicates, how many "empty" pixels
	(pixels with deasserted Data Enable signal) are necessary to generate the
	internal HSYNC pulse. The value must be greater than 1 and smaller than
	vsync_gap_length.

	pclk_frequency (R):
	Input pixel clock frequency in kHz.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the pixelclock field of the v4l2_bt_timings struct.

	*Note: The frequency_range parameter must be set properly first to get
	a valid frequency here.*

	hsync_width (R):
	Width of the HSYNC signal in PCLK clock ticks.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the hsync field of the v4l2_bt_timings struct.

	vsync_width (R):
	Width of the VSYNC signal in PCLK clock ticks.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the vsync field of the v4l2_bt_timings struct.

	hback_porch (R):
	Number of PCLK pulses between deassertion of the HSYNC signal and the first
	valid pixel in the video line (marked by DE=1).

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the hbackporch field of the v4l2_bt_timings struct.

	hfront_porch (R):
	Number of PCLK pulses between the end of the last valid pixel in the video
	line (marked by DE=1) and assertion of the HSYNC signal.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the hfrontporch field of the v4l2_bt_timings struct.

	vback_porch (R):
	Number of video lines between deassertion of the VSYNC signal and the video
	line with the first valid pixel (marked by DE=1).

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the vbackporch field of the v4l2_bt_timings struct.

	vfront_porch (R):
	Number of video lines between the end of the last valid pixel line (marked
	by DE=1) and assertion of the VSYNC signal.

	The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
	the vfrontporch field of the v4l2_bt_timings struct.

	frequency_range (RW)
	PLL frequency range of the OLDI input clock generator. The PLL frequency is
	derived from the Pixel Clock Frequency (PCLK) and is equal to PCLK if
	oldi_lane_width is set to "single" and PCLK/2 if oldi_lane_width is set to
	"dual".

	\| 0 - PLL < 50MHz (default)
	\| 1 - PLL >= 50MHz

	*Note: This parameter can not be changed while the input v4l2 device is
	open.*


	Common FPDL3/GMSL output parameters
	===================================

	output_id (R):
	Output number ID, zero based.

	video_source (RW):
	Output video source. If set to 0 or 1, the source is the corresponding card
	input and the v4l2 output devices are disabled. If set to 2 or 3, the source
	is the corresponding v4l2 video output device. The default is
	the corresponding v4l2 output, i.e. 2 for OUT1 and 3 for OUT2.

	\| 0 - input 0
	\| 1 - input 1
	\| 2 - v4l2 output 0
	\| 3 - v4l2 output 1

	*Note: This parameter can not be changed while ANY of the input/output v4l2
	devices is open.*

	display_width (RW):
	Display width. There is no autodetection of the connected display, so the
	proper value must be set before the start of streaming. The default width
	is 1280.

	*Note: This parameter can not be changed while the output v4l2 device is
	open.*

	display_height (RW):
	Display height. There is no autodetection of the connected display, so the
	proper value must be set before the start of streaming. The default height
	is 640.

	*Note: This parameter can not be changed while the output v4l2 device is
	open.*

	frame_rate (RW):
	Output video frame rate in frames per second. The default frame rate is
	60Hz.

	hsync_polarity (RW):
	HSYNC signal polarity.

	\| 0 - active low (default)
	\| 1 - active high

	vsync_polarity (RW):
	VSYNC signal polarity.

	\| 0 - active low (default)
	\| 1 - active high

	de_polarity (RW):
	DE signal polarity.

	\| 0 - active low
	\| 1 - active high (default)

	pclk_frequency (RW):
	Output pixel clock frequency. Allowed values are between 25000-190000(kHz)
	and there is a non-linear stepping between two consecutive allowed
	frequencies. The driver finds the nearest allowed frequency to the given
	value and sets it. When reading this property, you get the exact
	frequency set by the driver. The default frequency is 70000kHz.

	*Note: This parameter can not be changed while the output v4l2 device is
	open.*

	hsync_width (RW):
	Width of the HSYNC signal in pixels. The default value is 16.

	vsync_width (RW):
	Width of the VSYNC signal in video lines. The default value is 2.

	hback_porch (RW):
	Number of PCLK pulses between deassertion of the HSYNC signal and the first
	valid pixel in the video line (marked by DE=1). The default value is 32.

	hfront_porch (RW):
	Number of PCLK pulses between the end of the last valid pixel in the video
	line (marked by DE=1) and assertion of the HSYNC signal. The default value
	is 32.

	vback_porch (RW):
	Number of video lines between deassertion of the VSYNC signal and the video
	line with the first valid pixel (marked by DE=1). The default value is 2.

	vfront_porch (RW):
	Number of video lines between the end of the last valid pixel line (marked
	by DE=1) and assertion of the VSYNC signal. The default value is 2.


	FPDL3 specific input parameters
	===============================

	fpdl3_input_width (RW):
	Number of deserializer input lines.

	\| 0 - auto (default)
	\| 1 - single
	\| 2 - dual

	FPDL3 specific output parameters
	================================

	fpdl3_output_width (RW):
	Number of serializer output lines.

	\| 0 - auto (default)
	\| 1 - single
	\| 2 - dual

	GMSL specific input parameters
	==============================

	gmsl_mode (RW):
	GMSL speed mode.

	\| 0 - 12Gb/s (default)
	\| 1 - 6Gb/s
	\| 2 - 3Gb/s
	\| 3 - 1.5Gb/s

	gmsl_stream_id (RW):
	The GMSL multi-stream contains up to four video streams. This parameter
	selects which stream is captured by the video input. The value is the
	zero-based index of the stream. The default stream id is 0.

	*Note: This parameter can not be changed while the input v4l2 device is
	open.*

	gmsl_fec (RW):
	GMSL Forward Error Correction (FEC).

	\| 0 - disabled
	\| 1 - enabled (default)


	====================
	mgb4 mtd partitions
	====================

	The mgb4 driver creates a MTD device with two partitions:
	- mgb4-fw.X - FPGA firmware.
	- mgb4-data.X - Factory settings, e.g. card serial number.

	The mgb4-fw partition is writable and is used for FW updates, mgb4-data is
	read-only. The X attached to the partition name represents the card number.
	Depending on the CONFIG_MTD_PARTITIONED_MASTER kernel configuration, you may
	also have a third partition named mgb4-flash available in the system. This
	partition represents the whole, unpartitioned, card's FLASH memory and one should
	not fiddle with it...

	====================
	mgb4 iio (triggers)
	====================

	The mgb4 driver creates an Industrial I/O (IIO) device that provides trigger and
	signal level status capability. The following scan elements are available:

	activity:
	The trigger levels and pending status.

	\| bit 1 - trigger 1 pending
	\| bit 2 - trigger 2 pending
	\| bit 5 - trigger 1 level
	\| bit 6 - trigger 2 level

	timestamp:
	The trigger event timestamp.

	The iio device can operate either in "raw" mode where you can fetch the signal
	levels (activity bits 5 and 6) using sysfs access or in triggered buffer mode.
	In the triggered buffer mode you can follow the signal level changes (activity
	bits 1 and 2) using the iio device in /dev. If you enable the timestamps, you
	will also get the exact trigger event time that can be matched to a video frame
	(every mgb4 video frame has a timestamp with the same clock source).

	*Note: although the activity sample always contains all the status bits, it makes
	no sense to get the pending bits in raw mode or the level bits in the triggered
	buffer mode - the values do not represent valid data in such case.*