| Kernel driver jc42 | |
| ================== | |
| Supported chips: | |
| * Analog Devices ADT7408 | |
| Datasheets: | |
| https://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf | |
| * Atmel AT30TS00, AT30TS002A/B, AT30TSE004A | |
| Datasheets: | |
| http://www.atmel.com/Images/doc8585.pdf | |
| http://www.atmel.com/Images/doc8711.pdf | |
| http://www.atmel.com/Images/Atmel-8852-SEEPROM-AT30TSE002A-Datasheet.pdf | |
| http://www.atmel.com/Images/Atmel-8868-DTS-AT30TSE004A-Datasheet.pdf | |
| * IDT TSE2002B3, TSE2002GB2, TSE2004GB2, TS3000B3, TS3000GB0, TS3000GB2, | |
| TS3001GB2 | |
| Datasheets: | |
| Available from IDT web site | |
| * Maxim MAX6604 | |
| Datasheets: | |
| http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf | |
| * Microchip MCP9804, MCP9805, MCP9808, MCP98242, MCP98243, MCP98244, MCP9843 | |
| Datasheets: | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/25095A.pdf | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf | |
| https://ww1.microchip.com/downloads/en/DeviceDoc/22327A.pdf | |
| * NXP Semiconductors SE97, SE97B, SE98, SE98A | |
| Datasheets: | |
| https://www.nxp.com/documents/data_sheet/SE97.pdf | |
| https://www.nxp.com/documents/data_sheet/SE97B.pdf | |
| https://www.nxp.com/documents/data_sheet/SE98.pdf | |
| https://www.nxp.com/documents/data_sheet/SE98A.pdf | |
| * ON Semiconductor CAT34TS02, CAT6095 | |
| Datasheet: | |
| https://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF | |
| https://www.onsemi.com/pub/Collateral/CAT6095-D.PDF | |
| * ST Microelectronics STTS424, STTS424E02, STTS2002, STTS2004, STTS3000 | |
| Datasheets: | |
| http://www.st.com/web/en/resource/technical/document/datasheet/CD00157556.pdf | |
| http://www.st.com/web/en/resource/technical/document/datasheet/CD00157558.pdf | |
| http://www.st.com/web/en/resource/technical/document/datasheet/CD00266638.pdf | |
| http://www.st.com/web/en/resource/technical/document/datasheet/CD00225278.pdf | |
| http://www.st.com/web/en/resource/technical/document/datasheet/DM00076709.pdf | |
| * JEDEC JC 42.4 compliant temperature sensor chips | |
| Datasheet: | |
| http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf | |
| Common for all chips: | |
| Prefix: 'jc42' | |
| Addresses scanned: I2C 0x18 - 0x1f | |
| Author: | |
| Guenter Roeck <linux@roeck-us.net> | |
| Description | |
| ----------- | |
| This driver implements support for JEDEC JC 42.4 compliant temperature sensors, | |
| which are used on many DDR3 memory modules for mobile devices and servers. Some | |
| systems use the sensor to prevent memory overheating by automatically throttling | |
| the memory controller. | |
| The driver auto-detects the chips listed above, but can be manually instantiated | |
| to support other JC 42.4 compliant chips. | |
| Example: the following will load the driver for a generic JC 42.4 compliant | |
| temperature sensor at address 0x18 on I2C bus #1:: | |
| # modprobe jc42 | |
| # echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device | |
| A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum, | |
| and critical temperature can be configured. There are alarms for high, low, | |
| and critical thresholds. | |
| There is also an hysteresis to control the thresholds for resetting alarms. | |
| Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5, | |
| 3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those | |
| limits. The chip supports only a single register to configure the hysteresis, | |
| which applies to all limits. This register can be written by writing into | |
| temp1_crit_hyst. Other hysteresis attributes are read-only. | |
| If the BIOS has configured the sensor for automatic temperature management, it | |
| is likely that it has locked the registers, i.e., that the temperature limits | |
| cannot be changed. | |
| Sysfs entries | |
| ------------- | |
| ======================= =========================================== | |
| temp1_input Temperature (RO) | |
| temp1_min Minimum temperature (RO or RW) | |
| temp1_max Maximum temperature (RO or RW) | |
| temp1_crit Critical high temperature (RO or RW) | |
| temp1_crit_hyst Critical hysteresis temperature (RO or RW) | |
| temp1_max_hyst Maximum hysteresis temperature (RO) | |
| temp1_min_alarm Temperature low alarm | |
| temp1_max_alarm Temperature high alarm | |
| temp1_crit_alarm Temperature critical alarm | |
| ======================= =========================================== |