| // SPDX-License-Identifier: GPL-2.0-or-later | |
| /* | |
| * pxa-ssp.c -- ALSA Soc Audio Layer | |
| * | |
| * Copyright 2005,2008 Wolfson Microelectronics PLC. | |
| * Author: Liam Girdwood | |
| * Mark Brown <broonie@opensource.wolfsonmicro.com> | |
| * | |
| * TODO: | |
| * o Test network mode for > 16bit sample size | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/module.h> | |
| #include <linux/slab.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/clk.h> | |
| #include <linux/io.h> | |
| #include <linux/pxa2xx_ssp.h> | |
| #include <linux/of.h> | |
| #include <linux/dmaengine.h> | |
| #include <asm/irq.h> | |
| #include <sound/core.h> | |
| #include <sound/pcm.h> | |
| #include <sound/initval.h> | |
| #include <sound/pcm_params.h> | |
| #include <sound/soc.h> | |
| #include <sound/dmaengine_pcm.h> | |
| #include "pxa2xx-lib.h" | |
| #include "pxa-ssp.h" | |
| /* | |
| * SSP audio private data | |
| */ | |
| struct ssp_priv { | |
| struct ssp_device *ssp; | |
| struct clk *extclk; | |
| unsigned long ssp_clk; | |
| unsigned int sysclk; | |
| unsigned int dai_fmt; | |
| unsigned int configured_dai_fmt; | |
| #ifdef CONFIG_PM | |
| uint32_t cr0; | |
| uint32_t cr1; | |
| uint32_t to; | |
| uint32_t psp; | |
| #endif | |
| }; | |
| static void dump_registers(struct ssp_device *ssp) | |
| { | |
| dev_dbg(ssp->dev, "SSCR0 0x%08x SSCR1 0x%08x SSTO 0x%08x\n", | |
| pxa_ssp_read_reg(ssp, SSCR0), pxa_ssp_read_reg(ssp, SSCR1), | |
| pxa_ssp_read_reg(ssp, SSTO)); | |
| dev_dbg(ssp->dev, "SSPSP 0x%08x SSSR 0x%08x SSACD 0x%08x\n", | |
| pxa_ssp_read_reg(ssp, SSPSP), pxa_ssp_read_reg(ssp, SSSR), | |
| pxa_ssp_read_reg(ssp, SSACD)); | |
| } | |
| static void pxa_ssp_set_dma_params(struct ssp_device *ssp, int width4, | |
| int out, struct snd_dmaengine_dai_dma_data *dma) | |
| { | |
| dma->addr_width = width4 ? DMA_SLAVE_BUSWIDTH_4_BYTES : | |
| DMA_SLAVE_BUSWIDTH_2_BYTES; | |
| dma->maxburst = 16; | |
| dma->addr = ssp->phys_base + SSDR; | |
| } | |
| static int pxa_ssp_startup(struct snd_pcm_substream *substream, | |
| struct snd_soc_dai *cpu_dai) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| struct snd_dmaengine_dai_dma_data *dma; | |
| int ret = 0; | |
| if (!snd_soc_dai_active(cpu_dai)) { | |
| clk_prepare_enable(ssp->clk); | |
| pxa_ssp_disable(ssp); | |
| } | |
| clk_prepare_enable(priv->extclk); | |
| dma = kzalloc_obj(struct snd_dmaengine_dai_dma_data); | |
| if (!dma) | |
| return -ENOMEM; | |
| dma->chan_name = substream->stream == SNDRV_PCM_STREAM_PLAYBACK ? | |
| "tx" : "rx"; | |
| snd_soc_dai_set_dma_data(cpu_dai, substream, dma); | |
| return ret; | |
| } | |
| static void pxa_ssp_shutdown(struct snd_pcm_substream *substream, | |
| struct snd_soc_dai *cpu_dai) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| if (!snd_soc_dai_active(cpu_dai)) { | |
| pxa_ssp_disable(ssp); | |
| clk_disable_unprepare(ssp->clk); | |
| } | |
| clk_disable_unprepare(priv->extclk); | |
| kfree(snd_soc_dai_get_dma_data(cpu_dai, substream)); | |
| snd_soc_dai_set_dma_data(cpu_dai, substream, NULL); | |
| } | |
| #ifdef CONFIG_PM | |
| static int pxa_ssp_suspend(struct snd_soc_component *component) | |
| { | |
| struct ssp_priv *priv = snd_soc_component_get_drvdata(component); | |
| struct ssp_device *ssp = priv->ssp; | |
| if (!snd_soc_component_active(component)) | |
| clk_prepare_enable(ssp->clk); | |
| priv->cr0 = __raw_readl(ssp->mmio_base + SSCR0); | |
| priv->cr1 = __raw_readl(ssp->mmio_base + SSCR1); | |
| priv->to = __raw_readl(ssp->mmio_base + SSTO); | |
| priv->psp = __raw_readl(ssp->mmio_base + SSPSP); | |
| pxa_ssp_disable(ssp); | |
| clk_disable_unprepare(ssp->clk); | |
| return 0; | |
| } | |
| static int pxa_ssp_resume(struct snd_soc_component *component) | |
| { | |
| struct ssp_priv *priv = snd_soc_component_get_drvdata(component); | |
| struct ssp_device *ssp = priv->ssp; | |
| uint32_t sssr = SSSR_ROR | SSSR_TUR | SSSR_BCE; | |
| clk_prepare_enable(ssp->clk); | |
| __raw_writel(sssr, ssp->mmio_base + SSSR); | |
| __raw_writel(priv->cr0 & ~SSCR0_SSE, ssp->mmio_base + SSCR0); | |
| __raw_writel(priv->cr1, ssp->mmio_base + SSCR1); | |
| __raw_writel(priv->to, ssp->mmio_base + SSTO); | |
| __raw_writel(priv->psp, ssp->mmio_base + SSPSP); | |
| if (snd_soc_component_active(component)) | |
| pxa_ssp_enable(ssp); | |
| else | |
| clk_disable_unprepare(ssp->clk); | |
| return 0; | |
| } | |
| #else | |
| #define pxa_ssp_suspend NULL | |
| #define pxa_ssp_resume NULL | |
| #endif | |
| /* | |
| * ssp_set_clkdiv - set SSP clock divider | |
| * @div: serial clock rate divider | |
| */ | |
| static void pxa_ssp_set_scr(struct ssp_device *ssp, u32 div) | |
| { | |
| u32 sscr0 = pxa_ssp_read_reg(ssp, SSCR0); | |
| if (ssp->type == PXA25x_SSP) { | |
| sscr0 &= ~0x0000ff00; | |
| sscr0 |= ((div - 2)/2) << 8; /* 2..512 */ | |
| } else { | |
| sscr0 &= ~0x000fff00; | |
| sscr0 |= (div - 1) << 8; /* 1..4096 */ | |
| } | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0); | |
| } | |
| /* | |
| * Set the SSP ports SYSCLK. | |
| */ | |
| static int pxa_ssp_set_dai_sysclk(struct snd_soc_dai *cpu_dai, | |
| int clk_id, unsigned int freq, int dir) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| u32 sscr0 = pxa_ssp_read_reg(ssp, SSCR0) & | |
| ~(SSCR0_ECS | SSCR0_NCS | SSCR0_MOD | SSCR0_ACS); | |
| if (priv->extclk) { | |
| int ret; | |
| /* | |
| * For DT based boards, if an extclk is given, use it | |
| * here and configure PXA_SSP_CLK_EXT. | |
| */ | |
| ret = clk_set_rate(priv->extclk, freq); | |
| if (ret < 0) | |
| return ret; | |
| clk_id = PXA_SSP_CLK_EXT; | |
| } | |
| dev_dbg(ssp->dev, | |
| "pxa_ssp_set_dai_sysclk id: %d, clk_id %d, freq %u\n", | |
| cpu_dai->id, clk_id, freq); | |
| switch (clk_id) { | |
| case PXA_SSP_CLK_NET_PLL: | |
| sscr0 |= SSCR0_MOD; | |
| break; | |
| case PXA_SSP_CLK_PLL: | |
| /* Internal PLL is fixed */ | |
| if (ssp->type == PXA25x_SSP) | |
| priv->sysclk = 1843200; | |
| else | |
| priv->sysclk = 13000000; | |
| break; | |
| case PXA_SSP_CLK_EXT: | |
| priv->sysclk = freq; | |
| sscr0 |= SSCR0_ECS; | |
| break; | |
| case PXA_SSP_CLK_NET: | |
| priv->sysclk = freq; | |
| sscr0 |= SSCR0_NCS | SSCR0_MOD; | |
| break; | |
| case PXA_SSP_CLK_AUDIO: | |
| priv->sysclk = 0; | |
| pxa_ssp_set_scr(ssp, 1); | |
| sscr0 |= SSCR0_ACS; | |
| break; | |
| default: | |
| return -ENODEV; | |
| } | |
| /* The SSP clock must be disabled when changing SSP clock mode | |
| * on PXA2xx. On PXA3xx it must be enabled when doing so. */ | |
| if (ssp->type != PXA3xx_SSP) | |
| clk_disable_unprepare(ssp->clk); | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0); | |
| if (ssp->type != PXA3xx_SSP) | |
| clk_prepare_enable(ssp->clk); | |
| return 0; | |
| } | |
| /* | |
| * Configure the PLL frequency pxa27x and (afaik - pxa320 only) | |
| */ | |
| static int pxa_ssp_set_pll(struct ssp_priv *priv, unsigned int freq) | |
| { | |
| struct ssp_device *ssp = priv->ssp; | |
| u32 ssacd = pxa_ssp_read_reg(ssp, SSACD) & ~0x70; | |
| if (ssp->type == PXA3xx_SSP) | |
| pxa_ssp_write_reg(ssp, SSACDD, 0); | |
| switch (freq) { | |
| case 5622000: | |
| break; | |
| case 11345000: | |
| ssacd |= (0x1 << 4); | |
| break; | |
| case 12235000: | |
| ssacd |= (0x2 << 4); | |
| break; | |
| case 14857000: | |
| ssacd |= (0x3 << 4); | |
| break; | |
| case 32842000: | |
| ssacd |= (0x4 << 4); | |
| break; | |
| case 48000000: | |
| ssacd |= (0x5 << 4); | |
| break; | |
| case 0: | |
| /* Disable */ | |
| break; | |
| default: | |
| /* PXA3xx has a clock ditherer which can be used to generate | |
| * a wider range of frequencies - calculate a value for it. | |
| */ | |
| if (ssp->type == PXA3xx_SSP) { | |
| u32 val; | |
| u64 tmp = 19968; | |
| tmp *= 1000000; | |
| do_div(tmp, freq); | |
| val = tmp; | |
| val = (val << 16) | 64; | |
| pxa_ssp_write_reg(ssp, SSACDD, val); | |
| ssacd |= (0x6 << 4); | |
| dev_dbg(ssp->dev, | |
| "Using SSACDD %x to supply %uHz\n", | |
| val, freq); | |
| break; | |
| } | |
| return -EINVAL; | |
| } | |
| pxa_ssp_write_reg(ssp, SSACD, ssacd); | |
| return 0; | |
| } | |
| /* | |
| * Set the active slots in TDM/Network mode | |
| */ | |
| static int pxa_ssp_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, | |
| unsigned int tx_mask, unsigned int rx_mask, int slots, int slot_width) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| u32 sscr0; | |
| sscr0 = pxa_ssp_read_reg(ssp, SSCR0); | |
| sscr0 &= ~(SSCR0_MOD | SSCR0_SlotsPerFrm(8) | SSCR0_EDSS | SSCR0_DSS); | |
| /* set slot width */ | |
| if (slot_width > 16) | |
| sscr0 |= SSCR0_EDSS | SSCR0_DataSize(slot_width - 16); | |
| else | |
| sscr0 |= SSCR0_DataSize(slot_width); | |
| if (slots > 1) { | |
| /* enable network mode */ | |
| sscr0 |= SSCR0_MOD; | |
| /* set number of active slots */ | |
| sscr0 |= SSCR0_SlotsPerFrm(slots); | |
| /* set active slot mask */ | |
| pxa_ssp_write_reg(ssp, SSTSA, tx_mask); | |
| pxa_ssp_write_reg(ssp, SSRSA, rx_mask); | |
| } | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0); | |
| return 0; | |
| } | |
| /* | |
| * Tristate the SSP DAI lines | |
| */ | |
| static int pxa_ssp_set_dai_tristate(struct snd_soc_dai *cpu_dai, | |
| int tristate) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| u32 sscr1; | |
| sscr1 = pxa_ssp_read_reg(ssp, SSCR1); | |
| if (tristate) | |
| sscr1 &= ~SSCR1_TTE; | |
| else | |
| sscr1 |= SSCR1_TTE; | |
| pxa_ssp_write_reg(ssp, SSCR1, sscr1); | |
| return 0; | |
| } | |
| static int pxa_ssp_set_dai_fmt(struct snd_soc_dai *cpu_dai, | |
| unsigned int fmt) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { | |
| case SND_SOC_DAIFMT_BC_FC: | |
| case SND_SOC_DAIFMT_BC_FP: | |
| case SND_SOC_DAIFMT_BP_FP: | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { | |
| case SND_SOC_DAIFMT_NB_NF: | |
| case SND_SOC_DAIFMT_NB_IF: | |
| case SND_SOC_DAIFMT_IB_IF: | |
| case SND_SOC_DAIFMT_IB_NF: | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_I2S: | |
| case SND_SOC_DAIFMT_DSP_A: | |
| case SND_SOC_DAIFMT_DSP_B: | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| /* Settings will be applied in hw_params() */ | |
| priv->dai_fmt = fmt; | |
| return 0; | |
| } | |
| /* | |
| * Set up the SSP DAI format. | |
| * The SSP Port must be inactive before calling this function as the | |
| * physical interface format is changed. | |
| */ | |
| static int pxa_ssp_configure_dai_fmt(struct ssp_priv *priv) | |
| { | |
| struct ssp_device *ssp = priv->ssp; | |
| u32 sscr0, sscr1, sspsp, scfr; | |
| /* check if we need to change anything at all */ | |
| if (priv->configured_dai_fmt == priv->dai_fmt) | |
| return 0; | |
| /* reset port settings */ | |
| sscr0 = pxa_ssp_read_reg(ssp, SSCR0) & | |
| ~(SSCR0_PSP | SSCR0_MOD); | |
| sscr1 = pxa_ssp_read_reg(ssp, SSCR1) & | |
| ~(SSCR1_SCLKDIR | SSCR1_SFRMDIR | SSCR1_SCFR | | |
| SSCR1_RWOT | SSCR1_TRAIL | SSCR1_TFT | SSCR1_RFT); | |
| sspsp = pxa_ssp_read_reg(ssp, SSPSP) & | |
| ~(SSPSP_SFRMP | SSPSP_SCMODE(3)); | |
| sscr1 |= SSCR1_RxTresh(8) | SSCR1_TxTresh(7); | |
| switch (priv->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { | |
| case SND_SOC_DAIFMT_BC_FC: | |
| sscr1 |= SSCR1_SCLKDIR | SSCR1_SFRMDIR | SSCR1_SCFR; | |
| break; | |
| case SND_SOC_DAIFMT_BC_FP: | |
| sscr1 |= SSCR1_SCLKDIR | SSCR1_SCFR; | |
| break; | |
| case SND_SOC_DAIFMT_BP_FP: | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (priv->dai_fmt & SND_SOC_DAIFMT_INV_MASK) { | |
| case SND_SOC_DAIFMT_NB_NF: | |
| sspsp |= SSPSP_SFRMP; | |
| break; | |
| case SND_SOC_DAIFMT_NB_IF: | |
| break; | |
| case SND_SOC_DAIFMT_IB_IF: | |
| sspsp |= SSPSP_SCMODE(2); | |
| break; | |
| case SND_SOC_DAIFMT_IB_NF: | |
| sspsp |= SSPSP_SCMODE(2) | SSPSP_SFRMP; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (priv->dai_fmt & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_I2S: | |
| sscr0 |= SSCR0_PSP; | |
| sscr1 |= SSCR1_RWOT | SSCR1_TRAIL; | |
| /* See hw_params() */ | |
| break; | |
| case SND_SOC_DAIFMT_DSP_A: | |
| sspsp |= SSPSP_FSRT; | |
| fallthrough; | |
| case SND_SOC_DAIFMT_DSP_B: | |
| sscr0 |= SSCR0_MOD | SSCR0_PSP; | |
| sscr1 |= SSCR1_TRAIL | SSCR1_RWOT; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0); | |
| pxa_ssp_write_reg(ssp, SSCR1, sscr1); | |
| pxa_ssp_write_reg(ssp, SSPSP, sspsp); | |
| switch (priv->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { | |
| case SND_SOC_DAIFMT_BC_FC: | |
| case SND_SOC_DAIFMT_BC_FP: | |
| scfr = pxa_ssp_read_reg(ssp, SSCR1) | SSCR1_SCFR; | |
| pxa_ssp_write_reg(ssp, SSCR1, scfr); | |
| while (pxa_ssp_read_reg(ssp, SSSR) & SSSR_BSY) | |
| cpu_relax(); | |
| break; | |
| } | |
| dump_registers(ssp); | |
| /* Since we are configuring the timings for the format by hand | |
| * we have to defer some things until hw_params() where we | |
| * know parameters like the sample size. | |
| */ | |
| priv->configured_dai_fmt = priv->dai_fmt; | |
| return 0; | |
| } | |
| struct pxa_ssp_clock_mode { | |
| int rate; | |
| int pll; | |
| u8 acds; | |
| u8 scdb; | |
| }; | |
| static const struct pxa_ssp_clock_mode pxa_ssp_clock_modes[] = { | |
| { .rate = 8000, .pll = 32842000, .acds = SSACD_ACDS_32, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 11025, .pll = 5622000, .acds = SSACD_ACDS_4, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 16000, .pll = 32842000, .acds = SSACD_ACDS_16, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 22050, .pll = 5622000, .acds = SSACD_ACDS_2, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 44100, .pll = 11345000, .acds = SSACD_ACDS_2, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 48000, .pll = 12235000, .acds = SSACD_ACDS_2, .scdb = SSACD_SCDB_4X }, | |
| { .rate = 96000, .pll = 12235000, .acds = SSACD_ACDS_4, .scdb = SSACD_SCDB_1X }, | |
| {} | |
| }; | |
| /* | |
| * Set the SSP audio DMA parameters and sample size. | |
| * Can be called multiple times by oss emulation. | |
| */ | |
| static int pxa_ssp_hw_params(struct snd_pcm_substream *substream, | |
| struct snd_pcm_hw_params *params, | |
| struct snd_soc_dai *cpu_dai) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| int chn = params_channels(params); | |
| u32 sscr0, sspsp; | |
| int width = snd_pcm_format_physical_width(params_format(params)); | |
| int ttsa = pxa_ssp_read_reg(ssp, SSTSA) & 0xf; | |
| struct snd_dmaengine_dai_dma_data *dma_data; | |
| int rate = params_rate(params); | |
| int bclk = rate * chn * (width / 8); | |
| int ret; | |
| dma_data = snd_soc_dai_get_dma_data(cpu_dai, substream); | |
| /* Network mode with one active slot (ttsa == 1) can be used | |
| * to force 16-bit frame width on the wire (for S16_LE), even | |
| * with two channels. Use 16-bit DMA transfers for this case. | |
| */ | |
| pxa_ssp_set_dma_params(ssp, | |
| ((chn == 2) && (ttsa != 1)) || (width == 32), | |
| substream->stream == SNDRV_PCM_STREAM_PLAYBACK, dma_data); | |
| /* we can only change the settings if the port is not in use */ | |
| if (pxa_ssp_read_reg(ssp, SSCR0) & SSCR0_SSE) | |
| return 0; | |
| ret = pxa_ssp_configure_dai_fmt(priv); | |
| if (ret < 0) | |
| return ret; | |
| /* clear selected SSP bits */ | |
| sscr0 = pxa_ssp_read_reg(ssp, SSCR0) & ~(SSCR0_DSS | SSCR0_EDSS); | |
| /* bit size */ | |
| switch (params_format(params)) { | |
| case SNDRV_PCM_FORMAT_S16_LE: | |
| if (ssp->type == PXA3xx_SSP) | |
| sscr0 |= SSCR0_FPCKE; | |
| sscr0 |= SSCR0_DataSize(16); | |
| break; | |
| case SNDRV_PCM_FORMAT_S24_LE: | |
| sscr0 |= (SSCR0_EDSS | SSCR0_DataSize(8)); | |
| break; | |
| case SNDRV_PCM_FORMAT_S32_LE: | |
| sscr0 |= (SSCR0_EDSS | SSCR0_DataSize(16)); | |
| break; | |
| } | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0); | |
| if (sscr0 & SSCR0_ACS) { | |
| ret = pxa_ssp_set_pll(priv, bclk); | |
| /* | |
| * If we were able to generate the bclk directly, | |
| * all is fine. Otherwise, look up the closest rate | |
| * from the table and also set the dividers. | |
| */ | |
| if (ret < 0) { | |
| const struct pxa_ssp_clock_mode *m; | |
| int ssacd; | |
| for (m = pxa_ssp_clock_modes; m->rate; m++) { | |
| if (m->rate == rate) | |
| break; | |
| } | |
| if (!m->rate) | |
| return -EINVAL; | |
| ret = pxa_ssp_set_pll(priv, bclk); | |
| if (ret < 0) | |
| return ret; | |
| ssacd = pxa_ssp_read_reg(ssp, SSACD); | |
| ssacd &= ~(SSACD_ACDS(7) | SSACD_SCDB_1X); | |
| ssacd |= SSACD_ACDS(m->acds); | |
| ssacd |= m->scdb; | |
| pxa_ssp_write_reg(ssp, SSACD, ssacd); | |
| } | |
| } else if (sscr0 & SSCR0_ECS) { | |
| /* | |
| * For setups with external clocking, the PLL and its diviers | |
| * are not active. Instead, the SCR bits in SSCR0 can be used | |
| * to divide the clock. | |
| */ | |
| pxa_ssp_set_scr(ssp, bclk / rate); | |
| } | |
| switch (priv->dai_fmt & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_I2S: | |
| sspsp = pxa_ssp_read_reg(ssp, SSPSP); | |
| if (((priv->sysclk / bclk) == 64) && (width == 16)) { | |
| /* This is a special case where the bitclk is 64fs | |
| * and we're not dealing with 2*32 bits of audio | |
| * samples. | |
| * | |
| * The SSP values used for that are all found out by | |
| * trying and failing a lot; some of the registers | |
| * needed for that mode are only available on PXA3xx. | |
| */ | |
| if (ssp->type != PXA3xx_SSP) | |
| return -EINVAL; | |
| sspsp |= SSPSP_SFRMWDTH(width * 2); | |
| sspsp |= SSPSP_SFRMDLY(width * 4); | |
| sspsp |= SSPSP_EDMYSTOP(3); | |
| sspsp |= SSPSP_DMYSTOP(3); | |
| sspsp |= SSPSP_DMYSTRT(1); | |
| } else { | |
| /* The frame width is the width the LRCLK is | |
| * asserted for; the delay is expressed in | |
| * half cycle units. We need the extra cycle | |
| * because the data starts clocking out one BCLK | |
| * after LRCLK changes polarity. | |
| */ | |
| sspsp |= SSPSP_SFRMWDTH(width + 1); | |
| sspsp |= SSPSP_SFRMDLY((width + 1) * 2); | |
| sspsp |= SSPSP_DMYSTRT(1); | |
| } | |
| pxa_ssp_write_reg(ssp, SSPSP, sspsp); | |
| break; | |
| default: | |
| break; | |
| } | |
| /* When we use a network mode, we always require TDM slots | |
| * - complain loudly and fail if they've not been set up yet. | |
| */ | |
| if ((sscr0 & SSCR0_MOD) && !ttsa) { | |
| dev_err(ssp->dev, "No TDM timeslot configured\n"); | |
| return -EINVAL; | |
| } | |
| dump_registers(ssp); | |
| return 0; | |
| } | |
| static void pxa_ssp_set_running_bit(struct snd_pcm_substream *substream, | |
| struct ssp_device *ssp, int value) | |
| { | |
| uint32_t sscr0 = pxa_ssp_read_reg(ssp, SSCR0); | |
| uint32_t sscr1 = pxa_ssp_read_reg(ssp, SSCR1); | |
| uint32_t sspsp = pxa_ssp_read_reg(ssp, SSPSP); | |
| uint32_t sssr = pxa_ssp_read_reg(ssp, SSSR); | |
| if (value && (sscr0 & SSCR0_SSE)) | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0 & ~SSCR0_SSE); | |
| if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { | |
| if (value) | |
| sscr1 |= SSCR1_TSRE; | |
| else | |
| sscr1 &= ~SSCR1_TSRE; | |
| } else { | |
| if (value) | |
| sscr1 |= SSCR1_RSRE; | |
| else | |
| sscr1 &= ~SSCR1_RSRE; | |
| } | |
| pxa_ssp_write_reg(ssp, SSCR1, sscr1); | |
| if (value) { | |
| pxa_ssp_write_reg(ssp, SSSR, sssr); | |
| pxa_ssp_write_reg(ssp, SSPSP, sspsp); | |
| pxa_ssp_write_reg(ssp, SSCR0, sscr0 | SSCR0_SSE); | |
| } | |
| } | |
| static int pxa_ssp_trigger(struct snd_pcm_substream *substream, int cmd, | |
| struct snd_soc_dai *cpu_dai) | |
| { | |
| int ret = 0; | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(cpu_dai); | |
| struct ssp_device *ssp = priv->ssp; | |
| int val; | |
| switch (cmd) { | |
| case SNDRV_PCM_TRIGGER_RESUME: | |
| pxa_ssp_enable(ssp); | |
| break; | |
| case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: | |
| pxa_ssp_set_running_bit(substream, ssp, 1); | |
| val = pxa_ssp_read_reg(ssp, SSSR); | |
| pxa_ssp_write_reg(ssp, SSSR, val); | |
| break; | |
| case SNDRV_PCM_TRIGGER_START: | |
| pxa_ssp_set_running_bit(substream, ssp, 1); | |
| break; | |
| case SNDRV_PCM_TRIGGER_STOP: | |
| pxa_ssp_set_running_bit(substream, ssp, 0); | |
| break; | |
| case SNDRV_PCM_TRIGGER_SUSPEND: | |
| pxa_ssp_disable(ssp); | |
| break; | |
| case SNDRV_PCM_TRIGGER_PAUSE_PUSH: | |
| pxa_ssp_set_running_bit(substream, ssp, 0); | |
| break; | |
| default: | |
| ret = -EINVAL; | |
| } | |
| dump_registers(ssp); | |
| return ret; | |
| } | |
| static int pxa_ssp_probe(struct snd_soc_dai *dai) | |
| { | |
| struct device *dev = dai->dev; | |
| struct ssp_priv *priv; | |
| int ret; | |
| priv = kzalloc_obj(struct ssp_priv); | |
| if (!priv) | |
| return -ENOMEM; | |
| if (dev->of_node) { | |
| struct device_node *ssp_handle; | |
| ssp_handle = of_parse_phandle(dev->of_node, "port", 0); | |
| if (!ssp_handle) { | |
| dev_err(dev, "unable to get 'port' phandle\n"); | |
| ret = -ENODEV; | |
| goto err_priv; | |
| } | |
| priv->ssp = pxa_ssp_request_of(ssp_handle, "SoC audio"); | |
| if (priv->ssp == NULL) { | |
| ret = -ENODEV; | |
| goto err_priv; | |
| } | |
| priv->extclk = devm_clk_get_optional(dev, "extclk"); | |
| if (IS_ERR(priv->extclk)) { | |
| ret = PTR_ERR(priv->extclk); | |
| goto err_priv; | |
| } | |
| } else { | |
| priv->ssp = pxa_ssp_request(dai->id + 1, "SoC audio"); | |
| if (priv->ssp == NULL) { | |
| ret = -ENODEV; | |
| goto err_priv; | |
| } | |
| } | |
| priv->dai_fmt = (unsigned int) -1; | |
| snd_soc_dai_set_drvdata(dai, priv); | |
| return 0; | |
| err_priv: | |
| kfree(priv); | |
| return ret; | |
| } | |
| static int pxa_ssp_remove(struct snd_soc_dai *dai) | |
| { | |
| struct ssp_priv *priv = snd_soc_dai_get_drvdata(dai); | |
| pxa_ssp_free(priv->ssp); | |
| kfree(priv); | |
| return 0; | |
| } | |
| #define PXA_SSP_RATES (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_11025 |\ | |
| SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_22050 | \ | |
| SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \ | |
| SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_64000 | \ | |
| SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000) | |
| #define PXA_SSP_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S32_LE) | |
| static const struct snd_soc_dai_ops pxa_ssp_dai_ops = { | |
| .probe = pxa_ssp_probe, | |
| .remove = pxa_ssp_remove, | |
| .startup = pxa_ssp_startup, | |
| .shutdown = pxa_ssp_shutdown, | |
| .trigger = pxa_ssp_trigger, | |
| .hw_params = pxa_ssp_hw_params, | |
| .set_sysclk = pxa_ssp_set_dai_sysclk, | |
| .set_fmt = pxa_ssp_set_dai_fmt, | |
| .set_tdm_slot = pxa_ssp_set_dai_tdm_slot, | |
| .set_tristate = pxa_ssp_set_dai_tristate, | |
| }; | |
| static struct snd_soc_dai_driver pxa_ssp_dai = { | |
| .playback = { | |
| .channels_min = 1, | |
| .channels_max = 8, | |
| .rates = PXA_SSP_RATES, | |
| .formats = PXA_SSP_FORMATS, | |
| }, | |
| .capture = { | |
| .channels_min = 1, | |
| .channels_max = 8, | |
| .rates = PXA_SSP_RATES, | |
| .formats = PXA_SSP_FORMATS, | |
| }, | |
| .ops = &pxa_ssp_dai_ops, | |
| }; | |
| static const struct snd_soc_component_driver pxa_ssp_component = { | |
| .name = "pxa-ssp", | |
| .pcm_new = pxa2xx_soc_pcm_new, | |
| .open = pxa2xx_soc_pcm_open, | |
| .close = pxa2xx_soc_pcm_close, | |
| .hw_params = pxa2xx_soc_pcm_hw_params, | |
| .prepare = pxa2xx_soc_pcm_prepare, | |
| .trigger = pxa2xx_soc_pcm_trigger, | |
| .pointer = pxa2xx_soc_pcm_pointer, | |
| .suspend = pxa_ssp_suspend, | |
| .resume = pxa_ssp_resume, | |
| .legacy_dai_naming = 1, | |
| }; | |
| #ifdef CONFIG_OF | |
| static const struct of_device_id pxa_ssp_of_ids[] = { | |
| { .compatible = "mrvl,pxa-ssp-dai" }, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids); | |
| #endif | |
| static int asoc_ssp_probe(struct platform_device *pdev) | |
| { | |
| return devm_snd_soc_register_component(&pdev->dev, &pxa_ssp_component, | |
| &pxa_ssp_dai, 1); | |
| } | |
| static struct platform_driver asoc_ssp_driver = { | |
| .driver = { | |
| .name = "pxa-ssp-dai", | |
| .of_match_table = of_match_ptr(pxa_ssp_of_ids), | |
| }, | |
| .probe = asoc_ssp_probe, | |
| }; | |
| module_platform_driver(asoc_ssp_driver); | |
| /* Module information */ | |
| MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>"); | |
| MODULE_DESCRIPTION("PXA SSP/PCM SoC Interface"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_ALIAS("platform:pxa-ssp-dai"); |