| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Copyright (c) 2017, 2020, The Linux Foundation. All rights reserved. | |
| * Copyright (c) 2021, Linaro Ltd. | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/clk-provider.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/io.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/phy/phy.h> | |
| #include <linux/phy/phy-dp.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <linux/reset.h> | |
| #include <linux/slab.h> | |
| #include <dt-bindings/phy/phy.h> | |
| #include "phy-qcom-qmp-dp-phy.h" | |
| #include "phy-qcom-qmp-qserdes-com-v4.h" | |
| #include "phy-qcom-qmp-qserdes-com-v6.h" | |
| #include "phy-qcom-qmp-qserdes-dp-com-v8.h" | |
| /* EDP_PHY registers */ | |
| #define DP_PHY_CFG 0x0010 | |
| #define DP_PHY_CFG_1 0x0014 | |
| #define DP_PHY_PD_CTL 0x001c | |
| #define DP_PHY_MODE 0x0020 | |
| #define DP_AUX_CFG_SIZE 13 | |
| #define DP_PHY_AUX_CFG(n) (0x24 + (0x04 * (n))) | |
| #define DP_PHY_AUX_INTERRUPT_MASK 0x0058 | |
| #define DP_PHY_VCO_DIV 0x0074 | |
| #define DP_PHY_TX0_TX1_LANE_CTL 0x007c | |
| #define DP_PHY_TX2_TX3_LANE_CTL 0x00a0 | |
| #define DP_PHY_STATUS 0x00e0 | |
| /* LANE_TXn registers */ | |
| #define TXn_CLKBUF_ENABLE 0x0000 | |
| #define TXn_TX_EMP_POST1_LVL 0x0004 | |
| #define TXn_TX_DRV_LVL 0x0014 | |
| #define TXn_TX_DRV_LVL_OFFSET 0x0018 | |
| #define TXn_RESET_TSYNC_EN 0x001c | |
| #define TXn_LDO_CONFIG 0x0084 | |
| #define TXn_TX_BAND 0x0028 | |
| #define TXn_RES_CODE_LANE_OFFSET_TX0 0x0044 | |
| #define TXn_RES_CODE_LANE_OFFSET_TX1 0x0048 | |
| #define TXn_TRANSCEIVER_BIAS_EN 0x0054 | |
| #define TXn_HIGHZ_DRVR_EN 0x0058 | |
| #define TXn_TX_POL_INV 0x005c | |
| #define TXn_LANE_MODE_1 0x0064 | |
| #define TXn_TRAN_DRVR_EMP_EN 0x0078 | |
| struct qcom_edp_swing_pre_emph_cfg { | |
| const u8 (*swing_hbr_rbr)[4][4]; | |
| const u8 (*swing_hbr3_hbr2)[4][4]; | |
| const u8 (*pre_emphasis_hbr_rbr)[4][4]; | |
| const u8 (*pre_emphasis_hbr3_hbr2)[4][4]; | |
| }; | |
| struct qcom_edp; | |
| struct phy_ver_ops { | |
| int (*com_power_on)(const struct qcom_edp *edp); | |
| int (*com_resetsm_cntrl)(const struct qcom_edp *edp); | |
| int (*com_bias_en_clkbuflr)(const struct qcom_edp *edp); | |
| int (*com_clk_fwd_cfg)(const struct qcom_edp *edp); | |
| int (*com_configure_pll)(const struct qcom_edp *edp); | |
| int (*com_configure_ssc)(const struct qcom_edp *edp); | |
| int (*com_ldo_config)(const struct qcom_edp *edp); | |
| }; | |
| struct qcom_edp_phy_cfg { | |
| bool is_edp; | |
| const u8 *aux_cfg; | |
| const u8 *vco_div_cfg; | |
| const struct qcom_edp_swing_pre_emph_cfg *dp_swing_pre_emph_cfg; | |
| const struct qcom_edp_swing_pre_emph_cfg *edp_swing_pre_emph_cfg; | |
| const struct phy_ver_ops *ver_ops; | |
| }; | |
| struct qcom_edp { | |
| struct device *dev; | |
| const struct qcom_edp_phy_cfg *cfg; | |
| struct phy *phy; | |
| void __iomem *edp; | |
| void __iomem *tx0; | |
| void __iomem *tx1; | |
| void __iomem *pll; | |
| struct clk_hw dp_link_hw; | |
| struct clk_hw dp_pixel_hw; | |
| struct phy_configure_opts_dp dp_opts; | |
| struct clk_bulk_data *clks; | |
| int num_clks; | |
| struct regulator_bulk_data supplies[2]; | |
| bool is_edp; | |
| }; | |
| static const u8 dp_swing_hbr_rbr[4][4] = { | |
| { 0x07, 0x0f, 0x16, 0x1f }, | |
| { 0x11, 0x1e, 0x1f, 0xff }, | |
| { 0x16, 0x1f, 0xff, 0xff }, | |
| { 0x1f, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 dp_pre_emp_hbr_rbr[4][4] = { | |
| { 0x00, 0x0e, 0x15, 0x1a }, | |
| { 0x00, 0x0e, 0x15, 0xff }, | |
| { 0x00, 0x0e, 0xff, 0xff }, | |
| { 0x04, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 dp_swing_hbr2_hbr3[4][4] = { | |
| { 0x02, 0x12, 0x16, 0x1a }, | |
| { 0x09, 0x19, 0x1f, 0xff }, | |
| { 0x10, 0x1f, 0xff, 0xff }, | |
| { 0x1f, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 dp_pre_emp_hbr2_hbr3[4][4] = { | |
| { 0x00, 0x0c, 0x15, 0x1b }, | |
| { 0x02, 0x0e, 0x16, 0xff }, | |
| { 0x02, 0x11, 0xff, 0xff }, | |
| { 0x04, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg = { | |
| .swing_hbr_rbr = &dp_swing_hbr_rbr, | |
| .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3, | |
| .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr, | |
| .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3, | |
| }; | |
| static const u8 dp_pre_emp_hbr_rbr_v8[4][4] = { | |
| { 0x00, 0x0e, 0x15, 0x1a }, | |
| { 0x00, 0x0e, 0x15, 0xff }, | |
| { 0x00, 0x0e, 0xff, 0xff }, | |
| { 0x00, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v8 = { | |
| .swing_hbr_rbr = &dp_swing_hbr_rbr, | |
| .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3, | |
| .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr_v8, | |
| .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3, | |
| }; | |
| static const u8 dp_swing_hbr2_hbr3_v2[4][4] = { | |
| { 0x27, 0x2f, 0x36, 0xff }, | |
| { 0x31, 0x3e, 0x3f, 0xff }, | |
| { 0x3a, 0x3f, 0xff, 0xff }, | |
| { 0xff, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 dp_pre_emp_hbr2_hbr3_v2[4][4] = { | |
| { 0x20, 0x2e, 0x35, 0xff }, | |
| { 0x20, 0x2e, 0x35, 0xff }, | |
| { 0x20, 0x2e, 0xff, 0xff }, | |
| { 0xff, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v2 = { | |
| /* | |
| * NOTE: The HPG does not specify a separate swing_hbr_rbr table. | |
| * Reuse the HBR2/HBR3 table for now. | |
| * | |
| * TODO: Update this once the HPG explicitly defines RBR/HBR swing values. | |
| */ | |
| .swing_hbr_rbr = &dp_swing_hbr2_hbr3_v2, | |
| .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3_v2, | |
| .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr2_hbr3_v2, | |
| .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3_v2, | |
| }; | |
| static const u8 edp_swing_hbr_rbr[4][4] = { | |
| { 0x07, 0x0f, 0x16, 0x1f }, | |
| { 0x0d, 0x16, 0x1e, 0xff }, | |
| { 0x11, 0x1b, 0xff, 0xff }, | |
| { 0x16, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 edp_pre_emp_hbr_rbr[4][4] = { | |
| { 0x05, 0x11, 0x17, 0x1d }, | |
| { 0x05, 0x11, 0x18, 0xff }, | |
| { 0x06, 0x11, 0xff, 0xff }, | |
| { 0x00, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 edp_swing_hbr2_hbr3[4][4] = { | |
| { 0x0b, 0x11, 0x17, 0x1c }, | |
| { 0x10, 0x19, 0x1f, 0xff }, | |
| { 0x19, 0x1f, 0xff, 0xff }, | |
| { 0x1f, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 edp_pre_emp_hbr2_hbr3[4][4] = { | |
| { 0x0c, 0x15, 0x19, 0x1e }, | |
| { 0x0b, 0x15, 0x19, 0xff }, | |
| { 0x0e, 0x14, 0xff, 0xff }, | |
| { 0x0d, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg = { | |
| .swing_hbr_rbr = &edp_swing_hbr_rbr, | |
| .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3, | |
| .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr, | |
| .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3, | |
| }; | |
| static const u8 edp_phy_aux_cfg_v4[DP_AUX_CFG_SIZE] = { | |
| 0x00, 0x13, 0x24, 0x00, 0x0a, 0x26, 0x0a, 0x03, 0x37, 0x03, 0x02, 0x02, 0x00, | |
| }; | |
| static const u8 edp_phy_vco_div_cfg_v4[4] = { | |
| 0x01, 0x01, 0x02, 0x00, | |
| }; | |
| static const u8 edp_pre_emp_hbr_rbr_v2[4][4] = { | |
| { 0x05, 0x12, 0x17, 0x1d }, | |
| { 0x05, 0x11, 0x18, 0xff }, | |
| { 0x06, 0x11, 0xff, 0xff }, | |
| { 0x00, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 edp_pre_emp_hbr2_hbr3_v2[4][4] = { | |
| { 0x0c, 0x15, 0x19, 0x1e }, | |
| { 0x08, 0x15, 0x19, 0xff }, | |
| { 0x0e, 0x14, 0xff, 0xff }, | |
| { 0x0d, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { | |
| .swing_hbr_rbr = &edp_swing_hbr_rbr, | |
| .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3, | |
| .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr_v2, | |
| .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v2, | |
| }; | |
| static const u8 edp_swing_hbr2_hbr3_v3[4][4] = { | |
| { 0x06, 0x11, 0x16, 0x1b }, | |
| { 0x0b, 0x19, 0x1f, 0xff }, | |
| { 0x18, 0x1f, 0xff, 0xff }, | |
| { 0x1f, 0xff, 0xff, 0xff } | |
| }; | |
| static const u8 edp_pre_emp_hbr2_hbr3_v3[4][4] = { | |
| { 0x0c, 0x15, 0x19, 0x1e }, | |
| { 0x09, 0x14, 0x19, 0xff }, | |
| { 0x0f, 0x14, 0xff, 0xff }, | |
| { 0x0d, 0xff, 0xff, 0xff } | |
| }; | |
| static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v3 = { | |
| .swing_hbr_rbr = &edp_swing_hbr_rbr, | |
| .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3_v3, | |
| .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr, | |
| .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v3, | |
| }; | |
| static const u8 edp_phy_aux_cfg_v5[DP_AUX_CFG_SIZE] = { | |
| 0x00, 0x13, 0xa4, 0x00, 0x0a, 0x26, 0x0a, 0x03, 0x37, 0x03, 0x02, 0x02, 0x00, | |
| }; | |
| static const u8 edp_phy_aux_cfg_v8[DP_AUX_CFG_SIZE] = { | |
| 0x00, 0x00, 0xa0, 0x00, 0x0a, 0x26, 0x0a, 0x03, 0x37, 0x03, 0x02, 0x02, 0x04, | |
| }; | |
| static const u8 edp_phy_vco_div_cfg_v8[4] = { | |
| 0x00, 0x00, 0x02, 0x01, | |
| }; | |
| static int qcom_edp_phy_init(struct phy *phy) | |
| { | |
| struct qcom_edp *edp = phy_get_drvdata(phy); | |
| u8 aux_cfg[DP_AUX_CFG_SIZE]; | |
| int ret; | |
| ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); | |
| if (ret) | |
| return ret; | |
| ret = clk_bulk_prepare_enable(edp->num_clks, edp->clks); | |
| if (ret) | |
| goto out_disable_supplies; | |
| memcpy(aux_cfg, edp->cfg->aux_cfg, sizeof(aux_cfg)); | |
| ret = edp->cfg->ver_ops->com_clk_fwd_cfg(edp); | |
| if (ret) | |
| return ret; | |
| writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | | |
| DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN, | |
| edp->edp + DP_PHY_PD_CTL); | |
| ret = edp->cfg->ver_ops->com_bias_en_clkbuflr(edp); | |
| if (ret) | |
| return ret; | |
| writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL); | |
| msleep(20); | |
| writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | | |
| DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN | | |
| DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN, | |
| edp->edp + DP_PHY_PD_CTL); | |
| if (!edp->is_edp) | |
| aux_cfg[8] = 0xb7; | |
| writel(0xfc, edp->edp + DP_PHY_MODE); | |
| for (int i = 0; i < DP_AUX_CFG_SIZE; i++) | |
| writel(aux_cfg[i], edp->edp + DP_PHY_AUX_CFG(i)); | |
| writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK | | |
| PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK | | |
| PHY_AUX_REQ_ERR_MASK, edp->edp + DP_PHY_AUX_INTERRUPT_MASK); | |
| msleep(20); | |
| return 0; | |
| out_disable_supplies: | |
| regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); | |
| return ret; | |
| } | |
| static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configure_opts_dp *dp_opts) | |
| { | |
| const struct qcom_edp_swing_pre_emph_cfg *cfg; | |
| unsigned int v_level = 0; | |
| unsigned int p_level = 0; | |
| int ret; | |
| u8 swing; | |
| u8 emph; | |
| int i; | |
| if (edp->is_edp) | |
| cfg = edp->cfg->edp_swing_pre_emph_cfg; | |
| else | |
| cfg = edp->cfg->dp_swing_pre_emph_cfg; | |
| for (i = 0; i < dp_opts->lanes; i++) { | |
| v_level = max(v_level, dp_opts->voltage[i]); | |
| p_level = max(p_level, dp_opts->pre[i]); | |
| } | |
| if (dp_opts->link_rate <= 2700) { | |
| swing = (*cfg->swing_hbr_rbr)[v_level][p_level]; | |
| emph = (*cfg->pre_emphasis_hbr_rbr)[v_level][p_level]; | |
| } else { | |
| swing = (*cfg->swing_hbr3_hbr2)[v_level][p_level]; | |
| emph = (*cfg->pre_emphasis_hbr3_hbr2)[v_level][p_level]; | |
| } | |
| if (swing == 0xff || emph == 0xff) | |
| return -EINVAL; | |
| ret = edp->cfg->ver_ops->com_ldo_config(edp); | |
| if (ret) | |
| return ret; | |
| writel(swing, edp->tx0 + TXn_TX_DRV_LVL); | |
| writel(emph, edp->tx0 + TXn_TX_EMP_POST1_LVL); | |
| writel(swing, edp->tx1 + TXn_TX_DRV_LVL); | |
| writel(emph, edp->tx1 + TXn_TX_EMP_POST1_LVL); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_configure(struct phy *phy, union phy_configure_opts *opts) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &opts->dp; | |
| struct qcom_edp *edp = phy_get_drvdata(phy); | |
| int ret = 0; | |
| memcpy(&edp->dp_opts, dp_opts, sizeof(*dp_opts)); | |
| if (dp_opts->set_voltages) | |
| ret = qcom_edp_set_voltages(edp, dp_opts); | |
| return ret; | |
| } | |
| static int qcom_edp_configure_ssc(const struct qcom_edp *edp) | |
| { | |
| return edp->cfg->ver_ops->com_configure_ssc(edp); | |
| } | |
| static int qcom_edp_configure_pll(const struct qcom_edp *edp) | |
| { | |
| return edp->cfg->ver_ops->com_configure_pll(edp); | |
| } | |
| static int qcom_edp_set_vco_div(const struct qcom_edp *edp, unsigned long *pixel_freq) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 vco_div; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| vco_div = edp->cfg->vco_div_cfg[0]; | |
| *pixel_freq = 1620000000UL / 2; | |
| break; | |
| case 2700: | |
| vco_div = edp->cfg->vco_div_cfg[1]; | |
| *pixel_freq = 2700000000UL / 2; | |
| break; | |
| case 5400: | |
| vco_div = edp->cfg->vco_div_cfg[2]; | |
| *pixel_freq = 5400000000UL / 4; | |
| break; | |
| case 8100: | |
| vco_div = edp->cfg->vco_div_cfg[3]; | |
| *pixel_freq = 8100000000UL / 6; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(vco_div, edp->edp + DP_PHY_VCO_DIV); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_power_on_v4(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | | |
| DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN | | |
| DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN, | |
| edp->edp + DP_PHY_PD_CTL); | |
| writel(0xfc, edp->edp + DP_PHY_MODE); | |
| return readl_poll_timeout(edp->pll + QSERDES_V4_COM_CMN_STATUS, | |
| val, val & BIT(7), 5, 200); | |
| } | |
| static int qcom_edp_phy_com_resetsm_cntrl_v4(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(0x20, edp->pll + QSERDES_V4_COM_RESETSM_CNTRL); | |
| return readl_poll_timeout(edp->pll + QSERDES_V4_COM_C_READY_STATUS, | |
| val, val & BIT(0), 500, 10000); | |
| } | |
| static int qcom_edp_com_clk_fwd_cfg_v4(const struct qcom_edp *edp) | |
| { | |
| return 0; | |
| } | |
| static int qcom_edp_com_bias_en_clkbuflr_v4(const struct qcom_edp *edp) | |
| { | |
| /* Turn on BIAS current for PHY/PLL */ | |
| writel(0x17, edp->pll + QSERDES_V4_COM_BIAS_EN_CLKBUFLR_EN); | |
| return 0; | |
| } | |
| static int qcom_edp_com_configure_ssc_v4(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 step1; | |
| u32 step2; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| case 2700: | |
| case 8100: | |
| step1 = 0x45; | |
| step2 = 0x06; | |
| break; | |
| case 5400: | |
| step1 = 0x5c; | |
| step2 = 0x08; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + QSERDES_V4_COM_SSC_EN_CENTER); | |
| writel(0x00, edp->pll + QSERDES_V4_COM_SSC_ADJ_PER1); | |
| writel(0x36, edp->pll + QSERDES_V4_COM_SSC_PER1); | |
| writel(0x01, edp->pll + QSERDES_V4_COM_SSC_PER2); | |
| writel(step1, edp->pll + QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0); | |
| writel(step2, edp->pll + QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_com_configure_pll_v4(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 div_frac_start2_mode0; | |
| u32 div_frac_start3_mode0; | |
| u32 dec_start_mode0; | |
| u32 lock_cmp1_mode0; | |
| u32 lock_cmp2_mode0; | |
| u32 hsclk_sel; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| hsclk_sel = 0x5; | |
| dec_start_mode0 = 0x69; | |
| div_frac_start2_mode0 = 0x80; | |
| div_frac_start3_mode0 = 0x07; | |
| lock_cmp1_mode0 = 0x6f; | |
| lock_cmp2_mode0 = 0x08; | |
| break; | |
| case 2700: | |
| hsclk_sel = 0x3; | |
| dec_start_mode0 = 0x69; | |
| div_frac_start2_mode0 = 0x80; | |
| div_frac_start3_mode0 = 0x07; | |
| lock_cmp1_mode0 = 0x0f; | |
| lock_cmp2_mode0 = 0x0e; | |
| break; | |
| case 5400: | |
| hsclk_sel = 0x1; | |
| dec_start_mode0 = 0x8c; | |
| div_frac_start2_mode0 = 0x00; | |
| div_frac_start3_mode0 = 0x0a; | |
| lock_cmp1_mode0 = 0x1f; | |
| lock_cmp2_mode0 = 0x1c; | |
| break; | |
| case 8100: | |
| hsclk_sel = 0x0; | |
| dec_start_mode0 = 0x69; | |
| div_frac_start2_mode0 = 0x80; | |
| div_frac_start3_mode0 = 0x07; | |
| lock_cmp1_mode0 = 0x2f; | |
| lock_cmp2_mode0 = 0x2a; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + QSERDES_V4_COM_SVS_MODE_CLK_SEL); | |
| writel(0x0b, edp->pll + QSERDES_V4_COM_SYSCLK_EN_SEL); | |
| writel(0x02, edp->pll + QSERDES_V4_COM_SYS_CLK_CTRL); | |
| writel(0x0c, edp->pll + QSERDES_V4_COM_CLK_ENABLE1); | |
| writel(0x06, edp->pll + QSERDES_V4_COM_SYSCLK_BUF_ENABLE); | |
| writel(0x30, edp->pll + QSERDES_V4_COM_CLK_SELECT); | |
| writel(hsclk_sel, edp->pll + QSERDES_V4_COM_HSCLK_SEL); | |
| writel(0x0f, edp->pll + QSERDES_V4_COM_PLL_IVCO); | |
| writel(0x08, edp->pll + QSERDES_V4_COM_LOCK_CMP_EN); | |
| writel(0x36, edp->pll + QSERDES_V4_COM_PLL_CCTRL_MODE0); | |
| writel(0x16, edp->pll + QSERDES_V4_COM_PLL_RCTRL_MODE0); | |
| writel(0x06, edp->pll + QSERDES_V4_COM_CP_CTRL_MODE0); | |
| writel(dec_start_mode0, edp->pll + QSERDES_V4_COM_DEC_START_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V4_COM_DIV_FRAC_START1_MODE0); | |
| writel(div_frac_start2_mode0, edp->pll + QSERDES_V4_COM_DIV_FRAC_START2_MODE0); | |
| writel(div_frac_start3_mode0, edp->pll + QSERDES_V4_COM_DIV_FRAC_START3_MODE0); | |
| writel(0x02, edp->pll + QSERDES_V4_COM_CMN_CONFIG); | |
| writel(0x3f, edp->pll + QSERDES_V4_COM_INTEGLOOP_GAIN0_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V4_COM_INTEGLOOP_GAIN1_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V4_COM_VCO_TUNE_MAP); | |
| writel(lock_cmp1_mode0, edp->pll + QSERDES_V4_COM_LOCK_CMP1_MODE0); | |
| writel(lock_cmp2_mode0, edp->pll + QSERDES_V4_COM_LOCK_CMP2_MODE0); | |
| writel(0x0a, edp->pll + QSERDES_V4_COM_BG_TIMER); | |
| writel(0x14, edp->pll + QSERDES_V4_COM_CORECLK_DIV_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V4_COM_VCO_TUNE_CTRL); | |
| writel(0x17, edp->pll + QSERDES_V4_COM_BIAS_EN_CLKBUFLR_EN); | |
| writel(0x0f, edp->pll + QSERDES_V4_COM_CORE_CLK_EN); | |
| writel(0xa0, edp->pll + QSERDES_V4_COM_VCO_TUNE1_MODE0); | |
| writel(0x03, edp->pll + QSERDES_V4_COM_VCO_TUNE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_ldo_config_v3(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 ldo_config; | |
| if (!edp->is_edp) | |
| ldo_config = 0x0; | |
| else if (dp_opts->link_rate <= 2700) | |
| ldo_config = 0x81; | |
| else | |
| ldo_config = 0x41; | |
| writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG); | |
| writel(dp_opts->lanes > 2 ? ldo_config : 0x00, edp->tx1 + TXn_LDO_CONFIG); | |
| return 0; | |
| } | |
| static int qcom_edp_ldo_config_v4(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 ldo_config; | |
| if (!edp->is_edp) | |
| ldo_config = 0x0; | |
| else if (dp_opts->link_rate <= 2700) | |
| ldo_config = 0xc1; | |
| else | |
| ldo_config = 0x81; | |
| writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG); | |
| writel(dp_opts->lanes > 2 ? ldo_config : 0x00, edp->tx1 + TXn_LDO_CONFIG); | |
| return 0; | |
| } | |
| static const struct phy_ver_ops qcom_edp_phy_ops_v3 = { | |
| .com_power_on = qcom_edp_phy_power_on_v4, | |
| .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v4, | |
| .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v4, | |
| .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, | |
| .com_configure_pll = qcom_edp_com_configure_pll_v4, | |
| .com_configure_ssc = qcom_edp_com_configure_ssc_v4, | |
| .com_ldo_config = qcom_edp_ldo_config_v3, | |
| }; | |
| static const struct phy_ver_ops qcom_edp_phy_ops_v4 = { | |
| .com_power_on = qcom_edp_phy_power_on_v4, | |
| .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v4, | |
| .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v4, | |
| .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, | |
| .com_configure_pll = qcom_edp_com_configure_pll_v4, | |
| .com_configure_ssc = qcom_edp_com_configure_ssc_v4, | |
| .com_ldo_config = qcom_edp_ldo_config_v4, | |
| }; | |
| static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = { | |
| .is_edp = false, | |
| .aux_cfg = edp_phy_aux_cfg_v5, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, | |
| .ver_ops = &qcom_edp_phy_ops_v4, | |
| }; | |
| static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = { | |
| .aux_cfg = edp_phy_aux_cfg_v4, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v3, | |
| .ver_ops = &qcom_edp_phy_ops_v3, | |
| }; | |
| static const struct qcom_edp_phy_cfg sc8180x_dp_phy_cfg = { | |
| .aux_cfg = edp_phy_aux_cfg_v4, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v2, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v2, | |
| .ver_ops = &qcom_edp_phy_ops_v3, | |
| }; | |
| static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = { | |
| .aux_cfg = edp_phy_aux_cfg_v4, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, | |
| .ver_ops = &qcom_edp_phy_ops_v4, | |
| }; | |
| static const struct qcom_edp_phy_cfg sc8280xp_edp_phy_cfg = { | |
| .is_edp = true, | |
| .aux_cfg = edp_phy_aux_cfg_v4, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, | |
| .ver_ops = &qcom_edp_phy_ops_v4, | |
| }; | |
| static int qcom_edp_phy_power_on_v6(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | | |
| DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN | | |
| DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN, | |
| edp->edp + DP_PHY_PD_CTL); | |
| writel(0xfc, edp->edp + DP_PHY_MODE); | |
| return readl_poll_timeout(edp->pll + QSERDES_V6_COM_CMN_STATUS, | |
| val, val & BIT(7), 5, 200); | |
| } | |
| static int qcom_edp_phy_com_resetsm_cntrl_v6(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(0x20, edp->pll + QSERDES_V6_COM_RESETSM_CNTRL); | |
| return readl_poll_timeout(edp->pll + QSERDES_V6_COM_C_READY_STATUS, | |
| val, val & BIT(0), 500, 10000); | |
| } | |
| static int qcom_edp_com_bias_en_clkbuflr_v6(const struct qcom_edp *edp) | |
| { | |
| /* Turn on BIAS current for PHY/PLL */ | |
| writel(0x1f, edp->pll + QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN); | |
| return 0; | |
| } | |
| static int qcom_edp_com_configure_ssc_v6(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 step1; | |
| u32 step2; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| case 2700: | |
| case 8100: | |
| step1 = 0x92; | |
| step2 = 0x01; | |
| break; | |
| case 5400: | |
| step1 = 0x18; | |
| step2 = 0x02; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + QSERDES_V6_COM_SSC_EN_CENTER); | |
| writel(0x00, edp->pll + QSERDES_V6_COM_SSC_ADJ_PER1); | |
| writel(0x36, edp->pll + QSERDES_V6_COM_SSC_PER1); | |
| writel(0x01, edp->pll + QSERDES_V6_COM_SSC_PER2); | |
| writel(step1, edp->pll + QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0); | |
| writel(step2, edp->pll + QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_com_configure_pll_v6(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 div_frac_start2_mode0; | |
| u32 div_frac_start3_mode0; | |
| u32 dec_start_mode0; | |
| u32 lock_cmp1_mode0; | |
| u32 lock_cmp2_mode0; | |
| u32 code1_mode0; | |
| u32 code2_mode0; | |
| u32 hsclk_sel; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| hsclk_sel = 0x5; | |
| dec_start_mode0 = 0x34; | |
| div_frac_start2_mode0 = 0xc0; | |
| div_frac_start3_mode0 = 0x0b; | |
| lock_cmp1_mode0 = 0x37; | |
| lock_cmp2_mode0 = 0x04; | |
| code1_mode0 = 0x71; | |
| code2_mode0 = 0x0c; | |
| break; | |
| case 2700: | |
| hsclk_sel = 0x3; | |
| dec_start_mode0 = 0x34; | |
| div_frac_start2_mode0 = 0xc0; | |
| div_frac_start3_mode0 = 0x0b; | |
| lock_cmp1_mode0 = 0x07; | |
| lock_cmp2_mode0 = 0x07; | |
| code1_mode0 = 0x71; | |
| code2_mode0 = 0x0c; | |
| break; | |
| case 5400: | |
| hsclk_sel = 0x1; | |
| dec_start_mode0 = 0x46; | |
| div_frac_start2_mode0 = 0x00; | |
| div_frac_start3_mode0 = 0x05; | |
| lock_cmp1_mode0 = 0x0f; | |
| lock_cmp2_mode0 = 0x0e; | |
| code1_mode0 = 0x97; | |
| code2_mode0 = 0x10; | |
| break; | |
| case 8100: | |
| hsclk_sel = 0x0; | |
| dec_start_mode0 = 0x34; | |
| div_frac_start2_mode0 = 0xc0; | |
| div_frac_start3_mode0 = 0x0b; | |
| lock_cmp1_mode0 = 0x17; | |
| lock_cmp2_mode0 = 0x15; | |
| code1_mode0 = 0x71; | |
| code2_mode0 = 0x0c; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + QSERDES_V6_COM_SVS_MODE_CLK_SEL); | |
| writel(0x0b, edp->pll + QSERDES_V6_COM_SYSCLK_EN_SEL); | |
| writel(0x02, edp->pll + QSERDES_V6_COM_SYS_CLK_CTRL); | |
| writel(0x0c, edp->pll + QSERDES_V6_COM_CLK_ENABLE1); | |
| writel(0x06, edp->pll + QSERDES_V6_COM_SYSCLK_BUF_ENABLE); | |
| writel(0x30, edp->pll + QSERDES_V6_COM_CLK_SELECT); | |
| writel(hsclk_sel, edp->pll + QSERDES_V6_COM_HSCLK_SEL_1); | |
| writel(0x07, edp->pll + QSERDES_V6_COM_PLL_IVCO); | |
| writel(0x08, edp->pll + QSERDES_V6_COM_LOCK_CMP_EN); | |
| writel(0x36, edp->pll + QSERDES_V6_COM_PLL_CCTRL_MODE0); | |
| writel(0x16, edp->pll + QSERDES_V6_COM_PLL_RCTRL_MODE0); | |
| writel(0x06, edp->pll + QSERDES_V6_COM_CP_CTRL_MODE0); | |
| writel(dec_start_mode0, edp->pll + QSERDES_V6_COM_DEC_START_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V6_COM_DIV_FRAC_START1_MODE0); | |
| writel(div_frac_start2_mode0, edp->pll + QSERDES_V6_COM_DIV_FRAC_START2_MODE0); | |
| writel(div_frac_start3_mode0, edp->pll + QSERDES_V6_COM_DIV_FRAC_START3_MODE0); | |
| writel(0x12, edp->pll + QSERDES_V6_COM_CMN_CONFIG_1); | |
| writel(0x3f, edp->pll + QSERDES_V6_COM_INTEGLOOP_GAIN0_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V6_COM_INTEGLOOP_GAIN1_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V6_COM_VCO_TUNE_MAP); | |
| writel(lock_cmp1_mode0, edp->pll + QSERDES_V6_COM_LOCK_CMP1_MODE0); | |
| writel(lock_cmp2_mode0, edp->pll + QSERDES_V6_COM_LOCK_CMP2_MODE0); | |
| writel(0x0a, edp->pll + QSERDES_V6_COM_BG_TIMER); | |
| writel(0x14, edp->pll + QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0); | |
| writel(0x00, edp->pll + QSERDES_V6_COM_VCO_TUNE_CTRL); | |
| writel(0x1f, edp->pll + QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN); | |
| writel(0x0f, edp->pll + QSERDES_V6_COM_CORE_CLK_EN); | |
| writel(0xa0, edp->pll + QSERDES_V6_COM_VCO_TUNE1_MODE0); | |
| writel(0x03, edp->pll + QSERDES_V6_COM_VCO_TUNE2_MODE0); | |
| writel(code1_mode0, edp->pll + QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE0); | |
| writel(code2_mode0, edp->pll + QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_ldo_config_v6(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 ldo_config; | |
| if (!edp->is_edp) | |
| ldo_config = 0x0; | |
| else if (dp_opts->link_rate <= 2700) | |
| ldo_config = 0x51; | |
| else | |
| ldo_config = 0x91; | |
| writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG); | |
| writel(dp_opts->lanes > 2 ? ldo_config : 0x00, edp->tx1 + TXn_LDO_CONFIG); | |
| return 0; | |
| } | |
| static const struct phy_ver_ops qcom_edp_phy_ops_v6 = { | |
| .com_power_on = qcom_edp_phy_power_on_v6, | |
| .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v6, | |
| .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v6, | |
| .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, | |
| .com_configure_pll = qcom_edp_com_configure_pll_v6, | |
| .com_configure_ssc = qcom_edp_com_configure_ssc_v6, | |
| .com_ldo_config = qcom_edp_ldo_config_v6, | |
| }; | |
| static struct qcom_edp_phy_cfg x1e80100_phy_cfg = { | |
| .aux_cfg = edp_phy_aux_cfg_v4, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v4, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, | |
| .ver_ops = &qcom_edp_phy_ops_v6, | |
| }; | |
| static int qcom_edp_com_configure_ssc_v8(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 step1; | |
| u32 step2; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| case 2700: | |
| case 8100: | |
| step1 = 0x5b; | |
| step2 = 0x02; | |
| break; | |
| case 5400: | |
| step1 = 0x5b; | |
| step2 = 0x02; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + DP_QSERDES_V8_COM_SSC_EN_CENTER); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_SSC_ADJ_PER1); | |
| writel(0x6b, edp->pll + DP_QSERDES_V8_COM_SSC_PER1); | |
| writel(0x02, edp->pll + DP_QSERDES_V8_COM_SSC_PER2); | |
| writel(step1, edp->pll + DP_QSERDES_V8_COM_SSC_STEP_SIZE1_MODE0); | |
| writel(step2, edp->pll + DP_QSERDES_V8_COM_SSC_STEP_SIZE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_com_configure_pll_v8(const struct qcom_edp *edp) | |
| { | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| u32 div_frac_start2_mode0; | |
| u32 div_frac_start3_mode0; | |
| u32 dec_start_mode0; | |
| u32 lock_cmp1_mode0; | |
| u32 lock_cmp2_mode0; | |
| u32 code1_mode0; | |
| u32 code2_mode0; | |
| u32 hsclk_sel; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| hsclk_sel = 0x5; | |
| dec_start_mode0 = 0x34; | |
| div_frac_start2_mode0 = 0xc0; | |
| div_frac_start3_mode0 = 0x0b; | |
| lock_cmp1_mode0 = 0x37; | |
| lock_cmp2_mode0 = 0x04; | |
| code1_mode0 = 0x71; | |
| code2_mode0 = 0x0c; | |
| break; | |
| case 2700: | |
| hsclk_sel = 0x3; | |
| dec_start_mode0 = 0x34; | |
| div_frac_start2_mode0 = 0xc0; | |
| div_frac_start3_mode0 = 0x0b; | |
| lock_cmp1_mode0 = 0x07; | |
| lock_cmp2_mode0 = 0x07; | |
| code1_mode0 = 0x71; | |
| code2_mode0 = 0x0c; | |
| break; | |
| case 5400: | |
| case 8100: | |
| hsclk_sel = 0x2; | |
| dec_start_mode0 = 0x4f; | |
| div_frac_start2_mode0 = 0xa0; | |
| div_frac_start3_mode0 = 0x01; | |
| lock_cmp1_mode0 = 0x18; | |
| lock_cmp2_mode0 = 0x15; | |
| code1_mode0 = 0x14; | |
| code2_mode0 = 0x25; | |
| break; | |
| default: | |
| /* Other link rates aren't supported */ | |
| return -EINVAL; | |
| } | |
| writel(0x01, edp->pll + DP_QSERDES_V8_COM_SVS_MODE_CLK_SEL); | |
| writel(0x3b, edp->pll + DP_QSERDES_V8_COM_SYSCLK_EN_SEL); | |
| writel(0x02, edp->pll + DP_QSERDES_V8_COM_SYS_CLK_CTRL); | |
| writel(0x0c, edp->pll + DP_QSERDES_V8_COM_CLK_ENABLE1); | |
| writel(0x06, edp->pll + DP_QSERDES_V8_COM_SYSCLK_BUF_ENABLE); | |
| writel(0x30, edp->pll + DP_QSERDES_V8_COM_CLK_SELECT); | |
| writel(hsclk_sel, edp->pll + DP_QSERDES_V8_COM_HSCLK_SEL_1); | |
| writel(0x07, edp->pll + DP_QSERDES_V8_COM_PLL_IVCO); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP_EN); | |
| writel(0x36, edp->pll + DP_QSERDES_V8_COM_PLL_CCTRL_MODE0); | |
| writel(0x16, edp->pll + DP_QSERDES_V8_COM_PLL_RCTRL_MODE0); | |
| writel(0x06, edp->pll + DP_QSERDES_V8_COM_CP_CTRL_MODE0); | |
| writel(dec_start_mode0, edp->pll + DP_QSERDES_V8_COM_DEC_START_MODE0); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START1_MODE0); | |
| writel(div_frac_start2_mode0, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START2_MODE0); | |
| writel(div_frac_start3_mode0, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START3_MODE0); | |
| writel(0x96, edp->pll + DP_QSERDES_V8_COM_CMN_CONFIG_1); | |
| writel(0x3f, edp->pll + DP_QSERDES_V8_COM_INTEGLOOP_GAIN0_MODE0); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_INTEGLOOP_GAIN1_MODE0); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE_MAP); | |
| writel(lock_cmp1_mode0, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP1_MODE0); | |
| writel(lock_cmp2_mode0, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP2_MODE0); | |
| writel(0x0a, edp->pll + DP_QSERDES_V8_COM_BG_TIMER); | |
| writel(0x0a, edp->pll + DP_QSERDES_V8_COM_CORECLK_DIV_MODE0); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE_CTRL); | |
| writel(0x1f, edp->pll + DP_QSERDES_V8_COM_BIAS_EN_CLKBUFLR_EN); | |
| writel(0x00, edp->pll + DP_QSERDES_V8_COM_CORE_CLK_EN); | |
| writel(0xa0, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE1_MODE0); | |
| writel(0x01, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE2_MODE0); | |
| writel(code1_mode0, edp->pll + DP_QSERDES_V8_COM_BIN_VCOCAL_CMP_CODE1_MODE0); | |
| writel(code2_mode0, edp->pll + DP_QSERDES_V8_COM_BIN_VCOCAL_CMP_CODE2_MODE0); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_com_resetsm_cntrl_v8(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(0x20, edp->pll + DP_QSERDES_V8_COM_RESETSM_CNTRL); | |
| return readl_poll_timeout(edp->pll + DP_QSERDES_V8_COM_C_READY_STATUS, | |
| val, val & BIT(0), 500, 10000); | |
| } | |
| static int qcom_edp_com_clk_fwd_cfg_v8(const struct qcom_edp *edp) | |
| { | |
| writel(0x3f, edp->pll + DP_QSERDES_V8_COM_CLK_FWD_CONFIG_1); | |
| return 0; | |
| } | |
| static int qcom_edp_com_bias_en_clkbuflr_v8(const struct qcom_edp *edp) | |
| { | |
| /* Turn on BIAS current for PHY/PLL */ | |
| writel(0x1f, edp->pll + DP_QSERDES_V8_COM_BIAS_EN_CLKBUFLR_EN); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_power_on_v8(const struct qcom_edp *edp) | |
| { | |
| u32 val; | |
| writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | | |
| DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN | | |
| DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN, | |
| edp->edp + DP_PHY_PD_CTL); | |
| writel(0xfc, edp->edp + DP_PHY_MODE); | |
| return readl_poll_timeout(edp->pll + DP_QSERDES_V8_COM_CMN_STATUS, | |
| val, val & BIT(7), 5, 200); | |
| } | |
| static const struct phy_ver_ops qcom_edp_phy_ops_v8 = { | |
| .com_power_on = qcom_edp_phy_power_on_v8, | |
| .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v8, | |
| .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v8, | |
| .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v8, | |
| .com_configure_pll = qcom_edp_com_configure_pll_v8, | |
| .com_configure_ssc = qcom_edp_com_configure_ssc_v8, | |
| .com_ldo_config = qcom_edp_ldo_config_v6, | |
| }; | |
| static struct qcom_edp_phy_cfg glymur_phy_cfg = { | |
| .aux_cfg = edp_phy_aux_cfg_v8, | |
| .vco_div_cfg = edp_phy_vco_div_cfg_v8, | |
| .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v8, | |
| .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, | |
| .ver_ops = &qcom_edp_phy_ops_v8, | |
| }; | |
| static int qcom_edp_phy_power_on(struct phy *phy) | |
| { | |
| const struct qcom_edp *edp = phy_get_drvdata(phy); | |
| u32 bias0_en, drvr0_en, bias1_en, drvr1_en; | |
| unsigned long pixel_freq; | |
| int ret; | |
| u32 val; | |
| u8 cfg1; | |
| ret = edp->cfg->ver_ops->com_power_on(edp); | |
| if (ret) | |
| return ret; | |
| ret = edp->cfg->ver_ops->com_ldo_config(edp); | |
| if (ret) | |
| return ret; | |
| writel(0x00, edp->tx0 + TXn_LANE_MODE_1); | |
| writel(0x00, edp->tx1 + TXn_LANE_MODE_1); | |
| if (edp->dp_opts.ssc) { | |
| ret = qcom_edp_configure_ssc(edp); | |
| if (ret) | |
| return ret; | |
| } | |
| ret = qcom_edp_configure_pll(edp); | |
| if (ret) | |
| return ret; | |
| /* TX Lane configuration */ | |
| writel(0x05, edp->edp + DP_PHY_TX0_TX1_LANE_CTL); | |
| writel(0x05, edp->edp + DP_PHY_TX2_TX3_LANE_CTL); | |
| /* TX-0 register configuration */ | |
| writel(0x03, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN); | |
| writel(0x0f, edp->tx0 + TXn_CLKBUF_ENABLE); | |
| writel(0x03, edp->tx0 + TXn_RESET_TSYNC_EN); | |
| writel(0x01, edp->tx0 + TXn_TRAN_DRVR_EMP_EN); | |
| writel(0x04, edp->tx0 + TXn_TX_BAND); | |
| /* TX-1 register configuration */ | |
| writel(0x03, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN); | |
| writel(0x0f, edp->tx1 + TXn_CLKBUF_ENABLE); | |
| writel(0x03, edp->tx1 + TXn_RESET_TSYNC_EN); | |
| writel(0x01, edp->tx1 + TXn_TRAN_DRVR_EMP_EN); | |
| writel(0x04, edp->tx1 + TXn_TX_BAND); | |
| ret = qcom_edp_set_vco_div(edp, &pixel_freq); | |
| if (ret) | |
| return ret; | |
| writel(0x01, edp->edp + DP_PHY_CFG); | |
| writel(0x05, edp->edp + DP_PHY_CFG); | |
| writel(0x01, edp->edp + DP_PHY_CFG); | |
| writel(0x09, edp->edp + DP_PHY_CFG); | |
| ret = edp->cfg->ver_ops->com_resetsm_cntrl(edp); | |
| if (ret) | |
| return ret; | |
| writel(0x19, edp->edp + DP_PHY_CFG); | |
| writel(0x1f, edp->tx0 + TXn_HIGHZ_DRVR_EN); | |
| writel(0x04, edp->tx0 + TXn_HIGHZ_DRVR_EN); | |
| writel(0x00, edp->tx0 + TXn_TX_POL_INV); | |
| writel(0x1f, edp->tx1 + TXn_HIGHZ_DRVR_EN); | |
| writel(0x04, edp->tx1 + TXn_HIGHZ_DRVR_EN); | |
| writel(0x00, edp->tx1 + TXn_TX_POL_INV); | |
| writel(0x10, edp->tx0 + TXn_TX_DRV_LVL_OFFSET); | |
| writel(0x10, edp->tx1 + TXn_TX_DRV_LVL_OFFSET); | |
| writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX0); | |
| writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX1); | |
| writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX0); | |
| writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX1); | |
| writel(0x10, edp->tx0 + TXn_TX_EMP_POST1_LVL); | |
| writel(0x10, edp->tx1 + TXn_TX_EMP_POST1_LVL); | |
| writel(0x1f, edp->tx0 + TXn_TX_DRV_LVL); | |
| writel(0x1f, edp->tx1 + TXn_TX_DRV_LVL); | |
| if (edp->dp_opts.lanes == 1) { | |
| bias0_en = 0x01; | |
| bias1_en = 0x00; | |
| drvr0_en = 0x06; | |
| drvr1_en = 0x07; | |
| cfg1 = 0x1; | |
| } else if (edp->dp_opts.lanes == 2) { | |
| bias0_en = 0x03; | |
| bias1_en = 0x00; | |
| drvr0_en = 0x04; | |
| drvr1_en = 0x07; | |
| cfg1 = 0x3; | |
| } else { | |
| bias0_en = 0x03; | |
| bias1_en = 0x03; | |
| drvr0_en = 0x04; | |
| drvr1_en = 0x04; | |
| cfg1 = 0xf; | |
| } | |
| writel(drvr0_en, edp->tx0 + TXn_HIGHZ_DRVR_EN); | |
| writel(bias0_en, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN); | |
| writel(drvr1_en, edp->tx1 + TXn_HIGHZ_DRVR_EN); | |
| writel(bias1_en, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN); | |
| writel(cfg1, edp->edp + DP_PHY_CFG_1); | |
| writel(0x18, edp->edp + DP_PHY_CFG); | |
| usleep_range(100, 1000); | |
| writel(0x19, edp->edp + DP_PHY_CFG); | |
| ret = readl_poll_timeout(edp->edp + DP_PHY_STATUS, | |
| val, val & BIT(1), 500, 10000); | |
| if (ret) | |
| return ret; | |
| clk_set_rate(edp->dp_link_hw.clk, edp->dp_opts.link_rate * 100000); | |
| clk_set_rate(edp->dp_pixel_hw.clk, pixel_freq); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_power_off(struct phy *phy) | |
| { | |
| const struct qcom_edp *edp = phy_get_drvdata(phy); | |
| writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL); | |
| return 0; | |
| } | |
| static int qcom_edp_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode) | |
| { | |
| struct qcom_edp *edp = phy_get_drvdata(phy); | |
| if (mode != PHY_MODE_DP) | |
| return -EINVAL; | |
| edp->is_edp = submode == PHY_SUBMODE_EDP; | |
| return 0; | |
| } | |
| static int qcom_edp_phy_exit(struct phy *phy) | |
| { | |
| struct qcom_edp *edp = phy_get_drvdata(phy); | |
| clk_bulk_disable_unprepare(edp->num_clks, edp->clks); | |
| regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); | |
| return 0; | |
| } | |
| static const struct phy_ops qcom_edp_ops = { | |
| .init = qcom_edp_phy_init, | |
| .configure = qcom_edp_phy_configure, | |
| .power_on = qcom_edp_phy_power_on, | |
| .power_off = qcom_edp_phy_power_off, | |
| .set_mode = qcom_edp_phy_set_mode, | |
| .exit = qcom_edp_phy_exit, | |
| .owner = THIS_MODULE, | |
| }; | |
| /* | |
| * Embedded Display Port PLL driver block diagram for branch clocks | |
| * | |
| * +------------------------------+ | |
| * | EDP_VCO_CLK | | |
| * | | | |
| * | +-------------------+ | | |
| * | | (EDP PLL/VCO) | | | |
| * | +---------+---------+ | | |
| * | v | | |
| * | +----------+-----------+ | | |
| * | | hsclk_divsel_clk_src | | | |
| * | +----------+-----------+ | | |
| * +------------------------------+ | |
| * | | |
| * +---------<---------v------------>----------+ | |
| * | | | |
| * +--------v----------------+ | | |
| * | edp_phy_pll_link_clk | | | |
| * | link_clk | | | |
| * +--------+----------------+ | | |
| * | | | |
| * | | | |
| * v v | |
| * Input to DISPCC block | | |
| * for link clk, crypto clk | | |
| * and interface clock | | |
| * | | |
| * | | |
| * +--------<------------+-----------------+---<---+ | |
| * | | | | |
| * +----v---------+ +--------v-----+ +--------v------+ | |
| * | vco_divided | | vco_divided | | vco_divided | | |
| * | _clk_src | | _clk_src | | _clk_src | | |
| * | | | | | | | |
| * |divsel_six | | divsel_two | | divsel_four | | |
| * +-------+------+ +-----+--------+ +--------+------+ | |
| * | | | | |
| * v---->----------v-------------<------v | |
| * | | |
| * +----------+-----------------+ | |
| * | edp_phy_pll_vco_div_clk | | |
| * +---------+------------------+ | |
| * | | |
| * v | |
| * Input to DISPCC block | |
| * for EDP pixel clock | |
| * | |
| */ | |
| static int qcom_edp_dp_pixel_clk_determine_rate(struct clk_hw *hw, | |
| struct clk_rate_request *req) | |
| { | |
| switch (req->rate) { | |
| case 1620000000UL / 2: | |
| case 2700000000UL / 2: | |
| /* 5.4 and 8.1 GHz are same link rate as 2.7GHz, i.e. div 4 and div 6 */ | |
| return 0; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static unsigned long | |
| qcom_edp_dp_pixel_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) | |
| { | |
| const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_pixel_hw); | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| return 1620000000UL / 2; | |
| case 2700: | |
| return 2700000000UL / 2; | |
| case 5400: | |
| return 5400000000UL / 4; | |
| case 8100: | |
| return 8100000000UL / 6; | |
| default: | |
| return 0; | |
| } | |
| } | |
| static const struct clk_ops qcom_edp_dp_pixel_clk_ops = { | |
| .determine_rate = qcom_edp_dp_pixel_clk_determine_rate, | |
| .recalc_rate = qcom_edp_dp_pixel_clk_recalc_rate, | |
| }; | |
| static int qcom_edp_dp_link_clk_determine_rate(struct clk_hw *hw, | |
| struct clk_rate_request *req) | |
| { | |
| switch (req->rate) { | |
| case 162000000: | |
| case 270000000: | |
| case 540000000: | |
| case 810000000: | |
| return 0; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static unsigned long | |
| qcom_edp_dp_link_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) | |
| { | |
| const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_link_hw); | |
| const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; | |
| switch (dp_opts->link_rate) { | |
| case 1620: | |
| case 2700: | |
| case 5400: | |
| case 8100: | |
| return dp_opts->link_rate * 100000; | |
| default: | |
| return 0; | |
| } | |
| } | |
| static const struct clk_ops qcom_edp_dp_link_clk_ops = { | |
| .determine_rate = qcom_edp_dp_link_clk_determine_rate, | |
| .recalc_rate = qcom_edp_dp_link_clk_recalc_rate, | |
| }; | |
| static int qcom_edp_clks_register(struct qcom_edp *edp, struct device_node *np) | |
| { | |
| struct clk_hw_onecell_data *data; | |
| struct clk_init_data init = { }; | |
| char name[64]; | |
| int ret; | |
| data = devm_kzalloc(edp->dev, struct_size(data, hws, 2), GFP_KERNEL); | |
| if (!data) | |
| return -ENOMEM; | |
| data->num = 2; | |
| snprintf(name, sizeof(name), "%s::link_clk", dev_name(edp->dev)); | |
| init.ops = &qcom_edp_dp_link_clk_ops; | |
| init.name = name; | |
| edp->dp_link_hw.init = &init; | |
| ret = devm_clk_hw_register(edp->dev, &edp->dp_link_hw); | |
| if (ret) | |
| return ret; | |
| snprintf(name, sizeof(name), "%s::vco_div_clk", dev_name(edp->dev)); | |
| init.ops = &qcom_edp_dp_pixel_clk_ops; | |
| init.name = name; | |
| edp->dp_pixel_hw.init = &init; | |
| ret = devm_clk_hw_register(edp->dev, &edp->dp_pixel_hw); | |
| if (ret) | |
| return ret; | |
| data->hws[0] = &edp->dp_link_hw; | |
| data->hws[1] = &edp->dp_pixel_hw; | |
| return devm_of_clk_add_hw_provider(edp->dev, of_clk_hw_onecell_get, data); | |
| } | |
| static int qcom_edp_phy_probe(struct platform_device *pdev) | |
| { | |
| struct phy_provider *phy_provider; | |
| struct device *dev = &pdev->dev; | |
| struct qcom_edp *edp; | |
| int ret; | |
| edp = devm_kzalloc(dev, sizeof(*edp), GFP_KERNEL); | |
| if (!edp) | |
| return -ENOMEM; | |
| edp->dev = dev; | |
| edp->cfg = of_device_get_match_data(&pdev->dev); | |
| edp->is_edp = edp->cfg->is_edp; | |
| edp->edp = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(edp->edp)) | |
| return PTR_ERR(edp->edp); | |
| edp->tx0 = devm_platform_ioremap_resource(pdev, 1); | |
| if (IS_ERR(edp->tx0)) | |
| return PTR_ERR(edp->tx0); | |
| edp->tx1 = devm_platform_ioremap_resource(pdev, 2); | |
| if (IS_ERR(edp->tx1)) | |
| return PTR_ERR(edp->tx1); | |
| edp->pll = devm_platform_ioremap_resource(pdev, 3); | |
| if (IS_ERR(edp->pll)) | |
| return PTR_ERR(edp->pll); | |
| edp->num_clks = devm_clk_bulk_get_all(dev, &edp->clks); | |
| if (edp->num_clks < 0) | |
| return dev_err_probe(dev, edp->num_clks, "failed to get clocks\n"); | |
| edp->supplies[0].supply = "vdda-phy"; | |
| edp->supplies[1].supply = "vdda-pll"; | |
| ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); | |
| if (ret) | |
| return ret; | |
| ret = regulator_set_load(edp->supplies[0].consumer, 21800); /* 1.2 V vdda-phy */ | |
| if (ret) { | |
| dev_err(dev, "failed to set load at %s\n", edp->supplies[0].supply); | |
| return ret; | |
| } | |
| ret = regulator_set_load(edp->supplies[1].consumer, 36000); /* 0.9 V vdda-pll */ | |
| if (ret) { | |
| dev_err(dev, "failed to set load at %s\n", edp->supplies[1].supply); | |
| return ret; | |
| } | |
| ret = qcom_edp_clks_register(edp, pdev->dev.of_node); | |
| if (ret) | |
| return ret; | |
| edp->phy = devm_phy_create(dev, pdev->dev.of_node, &qcom_edp_ops); | |
| if (IS_ERR(edp->phy)) { | |
| dev_err(dev, "failed to register phy\n"); | |
| return PTR_ERR(edp->phy); | |
| } | |
| phy_set_drvdata(edp->phy, edp); | |
| phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); | |
| return PTR_ERR_OR_ZERO(phy_provider); | |
| } | |
| static const struct of_device_id qcom_edp_phy_match_table[] = { | |
| { .compatible = "qcom,glymur-dp-phy", .data = &glymur_phy_cfg, }, | |
| { .compatible = "qcom,sa8775p-edp-phy", .data = &sa8775p_dp_phy_cfg, }, | |
| { .compatible = "qcom,sc7280-edp-phy", .data = &sc7280_dp_phy_cfg, }, | |
| { .compatible = "qcom,sc8180x-edp-phy", .data = &sc8180x_dp_phy_cfg, }, | |
| { .compatible = "qcom,sc8280xp-dp-phy", .data = &sc8280xp_dp_phy_cfg, }, | |
| { .compatible = "qcom,sc8280xp-edp-phy", .data = &sc8280xp_edp_phy_cfg, }, | |
| { .compatible = "qcom,x1e80100-dp-phy", .data = &x1e80100_phy_cfg, }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, qcom_edp_phy_match_table); | |
| static struct platform_driver qcom_edp_phy_driver = { | |
| .probe = qcom_edp_phy_probe, | |
| .driver = { | |
| .name = "qcom-edp-phy", | |
| .of_match_table = qcom_edp_phy_match_table, | |
| }, | |
| }; | |
| module_platform_driver(qcom_edp_phy_driver); | |
| MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@linaro.org>"); | |
| MODULE_DESCRIPTION("Qualcomm eDP QMP PHY driver"); | |
| MODULE_LICENSE("GPL v2"); |