blob: 73b36d7c7b0d67309cce7bf0bd8a46f0c6ee7ea1 [file] [log] [blame]
/proc/sys/net/ipv4/* Variables:
ip_forward - BOOLEAN
0 - disabled (default)
not 0 - enabled
Forward Packets between interfaces.
This variable is special, its change resets all configuration
parameters to their default state (RFC1122 for hosts, RFC1812
for routers)
ip_default_ttl - INTEGER
Default value of TTL field (Time To Live) for outgoing (but not
forwarded) IP packets. Should be between 1 and 255 inclusive.
Default: 64 (as recommended by RFC1700)
ip_no_pmtu_disc - INTEGER
Disable Path MTU Discovery. If enabled in mode 1 and a
fragmentation-required ICMP is received, the PMTU to this
destination will be set to min_pmtu (see below). You will need
to raise min_pmtu to the smallest interface MTU on your system
manually if you want to avoid locally generated fragments.
In mode 2 incoming Path MTU Discovery messages will be
discarded. Outgoing frames are handled the same as in mode 1,
implicitly setting IP_PMTUDISC_DONT on every created socket.
Mode 3 is a hardend pmtu discover mode. The kernel will only
accept fragmentation-needed errors if the underlying protocol
can verify them besides a plain socket lookup. Current
protocols for which pmtu events will be honored are TCP, SCTP
and DCCP as they verify e.g. the sequence number or the
association. This mode should not be enabled globally but is
only intended to secure e.g. name servers in namespaces where
TCP path mtu must still work but path MTU information of other
protocols should be discarded. If enabled globally this mode
could break other protocols.
Possible values: 0-3
Default: FALSE
min_pmtu - INTEGER
default 552 - minimum discovered Path MTU
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the
case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
fwmark_reflect - BOOLEAN
Controls the fwmark of kernel-generated IPv4 reply packets that are not
associated with a socket for example, TCP RSTs or ICMP echo replies).
If unset, these packets have a fwmark of zero. If set, they have the
fwmark of the packet they are replying to.
Default: 0
route/max_size - INTEGER
Maximum number of routes allowed in the kernel. Increase
this when using large numbers of interfaces and/or routes.
From linux kernel 3.6 onwards, this is deprecated for ipv4
as route cache is no longer used.
neigh/default/gc_thresh1 - INTEGER
Minimum number of entries to keep. Garbage collector will not
purge entries if there are fewer than this number.
Default: 128
neigh/default/gc_thresh2 - INTEGER
Threshold when garbage collector becomes more aggressive about
purging entries. Entries older than 5 seconds will be cleared
when over this number.
Default: 512
neigh/default/gc_thresh3 - INTEGER
Maximum number of neighbor entries allowed. Increase this
when using large numbers of interfaces and when communicating
with large numbers of directly-connected peers.
Default: 1024
neigh/default/unres_qlen_bytes - INTEGER
The maximum number of bytes which may be used by packets
queued for each unresolved address by other network layers.
(added in linux 3.3)
Setting negative value is meaningless and will return error.
Default: 65536 Bytes(64KB)
neigh/default/unres_qlen - INTEGER
The maximum number of packets which may be queued for each
unresolved address by other network layers.
(deprecated in linux 3.3) : use unres_qlen_bytes instead.
Prior to linux 3.3, the default value is 3 which may cause
unexpected packet loss. The current default value is calculated
according to default value of unres_qlen_bytes and true size of
packet.
Default: 31
mtu_expires - INTEGER
Time, in seconds, that cached PMTU information is kept.
min_adv_mss - INTEGER
The advertised MSS depends on the first hop route MTU, but will
never be lower than this setting.
IP Fragmentation:
ipfrag_high_thresh - INTEGER
Maximum memory used to reassemble IP fragments. When
ipfrag_high_thresh bytes of memory is allocated for this purpose,
the fragment handler will toss packets until ipfrag_low_thresh
is reached. This also serves as a maximum limit to namespaces
different from the initial one.
ipfrag_low_thresh - INTEGER
Maximum memory used to reassemble IP fragments before the kernel
begins to remove incomplete fragment queues to free up resources.
The kernel still accepts new fragments for defragmentation.
ipfrag_time - INTEGER
Time in seconds to keep an IP fragment in memory.
ipfrag_max_dist - INTEGER
ipfrag_max_dist is a non-negative integer value which defines the
maximum "disorder" which is allowed among fragments which share a
common IP source address. Note that reordering of packets is
not unusual, but if a large number of fragments arrive from a source
IP address while a particular fragment queue remains incomplete, it
probably indicates that one or more fragments belonging to that queue
have been lost. When ipfrag_max_dist is positive, an additional check
is done on fragments before they are added to a reassembly queue - if
ipfrag_max_dist (or more) fragments have arrived from a particular IP
address between additions to any IP fragment queue using that source
address, it's presumed that one or more fragments in the queue are
lost. The existing fragment queue will be dropped, and a new one
started. An ipfrag_max_dist value of zero disables this check.
Using a very small value, e.g. 1 or 2, for ipfrag_max_dist can
result in unnecessarily dropping fragment queues when normal
reordering of packets occurs, which could lead to poor application
performance. Using a very large value, e.g. 50000, increases the
likelihood of incorrectly reassembling IP fragments that originate
from different IP datagrams, which could result in data corruption.
Default: 64
INET peer storage:
inet_peer_threshold - INTEGER
The approximate size of the storage. Starting from this threshold
entries will be thrown aggressively. This threshold also determines
entries' time-to-live and time intervals between garbage collection
passes. More entries, less time-to-live, less GC interval.
inet_peer_minttl - INTEGER
Minimum time-to-live of entries. Should be enough to cover fragment
time-to-live on the reassembling side. This minimum time-to-live is
guaranteed if the pool size is less than inet_peer_threshold.
Measured in seconds.
inet_peer_maxttl - INTEGER
Maximum time-to-live of entries. Unused entries will expire after
this period of time if there is no memory pressure on the pool (i.e.
when the number of entries in the pool is very small).
Measured in seconds.
TCP variables:
somaxconn - INTEGER
Limit of socket listen() backlog, known in userspace as SOMAXCONN.
Defaults to 128. See also tcp_max_syn_backlog for additional tuning
for TCP sockets.
tcp_abort_on_overflow - BOOLEAN
If listening service is too slow to accept new connections,
reset them. Default state is FALSE. It means that if overflow
occurred due to a burst, connection will recover. Enable this
option _only_ if you are really sure that listening daemon
cannot be tuned to accept connections faster. Enabling this
option can harm clients of your server.
tcp_adv_win_scale - INTEGER
Count buffering overhead as bytes/2^tcp_adv_win_scale
(if tcp_adv_win_scale > 0) or bytes-bytes/2^(-tcp_adv_win_scale),
if it is <= 0.
Possible values are [-31, 31], inclusive.
Default: 1
tcp_allowed_congestion_control - STRING
Show/set the congestion control choices available to non-privileged
processes. The list is a subset of those listed in
tcp_available_congestion_control.
Default is "reno" and the default setting (tcp_congestion_control).
tcp_app_win - INTEGER
Reserve max(window/2^tcp_app_win, mss) of window for application
buffer. Value 0 is special, it means that nothing is reserved.
Default: 31
tcp_autocorking - BOOLEAN
Enable TCP auto corking :
When applications do consecutive small write()/sendmsg() system calls,
we try to coalesce these small writes as much as possible, to lower
total amount of sent packets. This is done if at least one prior
packet for the flow is waiting in Qdisc queues or device transmit
queue. Applications can still use TCP_CORK for optimal behavior
when they know how/when to uncork their sockets.
Default : 1
tcp_available_congestion_control - STRING
Shows the available congestion control choices that are registered.
More congestion control algorithms may be available as modules,
but not loaded.
tcp_base_mss - INTEGER
The initial value of search_low to be used by the packetization layer
Path MTU discovery (MTU probing). If MTU probing is enabled,
this is the initial MSS used by the connection.
tcp_congestion_control - STRING
Set the congestion control algorithm to be used for new
connections. The algorithm "reno" is always available, but
additional choices may be available based on kernel configuration.
Default is set as part of kernel configuration.
For passive connections, the listener congestion control choice
is inherited.
[see setsockopt(listenfd, SOL_TCP, TCP_CONGESTION, "name" ...) ]
tcp_dsack - BOOLEAN
Allows TCP to send "duplicate" SACKs.
tcp_early_retrans - INTEGER
Enable Early Retransmit (ER), per RFC 5827. ER lowers the threshold
for triggering fast retransmit when the amount of outstanding data is
small and when no previously unsent data can be transmitted (such
that limited transmit could be used). Also controls the use of
Tail loss probe (TLP) that converts RTOs occurring due to tail
losses into fast recovery (draft-dukkipati-tcpm-tcp-loss-probe-01).
Possible values:
0 disables ER
1 enables ER
2 enables ER but delays fast recovery and fast retransmit
by a fourth of RTT. This mitigates connection falsely
recovers when network has a small degree of reordering
(less than 3 packets).
3 enables delayed ER and TLP.
4 enables TLP only.
Default: 3
tcp_ecn - INTEGER
Control use of Explicit Congestion Notification (ECN) by TCP.
ECN is used only when both ends of the TCP connection indicate
support for it. This feature is useful in avoiding losses due
to congestion by allowing supporting routers to signal
congestion before having to drop packets.
Possible values are:
0 Disable ECN. Neither initiate nor accept ECN.
1 Enable ECN when requested by incoming connections and
also request ECN on outgoing connection attempts.
2 Enable ECN when requested by incoming connections
but do not request ECN on outgoing connections.
Default: 2
tcp_ecn_fallback - BOOLEAN
If the kernel detects that ECN connection misbehaves, enable fall
back to non-ECN. Currently, this knob implements the fallback
from RFC3168, section 6.1.1.1., but we reserve that in future,
additional detection mechanisms could be implemented under this
knob. The value is not used, if tcp_ecn or per route (or congestion
control) ECN settings are disabled.
Default: 1 (fallback enabled)
tcp_fack - BOOLEAN
Enable FACK congestion avoidance and fast retransmission.
The value is not used, if tcp_sack is not enabled.
tcp_fin_timeout - INTEGER
The length of time an orphaned (no longer referenced by any
application) connection will remain in the FIN_WAIT_2 state
before it is aborted at the local end. While a perfectly
valid "receive only" state for an un-orphaned connection, an
orphaned connection in FIN_WAIT_2 state could otherwise wait
forever for the remote to close its end of the connection.
Cf. tcp_max_orphans
Default: 60 seconds
tcp_frto - INTEGER
Enables Forward RTO-Recovery (F-RTO) defined in RFC5682.
F-RTO is an enhanced recovery algorithm for TCP retransmission
timeouts. It is particularly beneficial in networks where the
RTT fluctuates (e.g., wireless). F-RTO is sender-side only
modification. It does not require any support from the peer.
By default it's enabled with a non-zero value. 0 disables F-RTO.
tcp_invalid_ratelimit - INTEGER
Limit the maximal rate for sending duplicate acknowledgments
in response to incoming TCP packets that are for an existing
connection but that are invalid due to any of these reasons:
(a) out-of-window sequence number,
(b) out-of-window acknowledgment number, or
(c) PAWS (Protection Against Wrapped Sequence numbers) check failure
This can help mitigate simple "ack loop" DoS attacks, wherein
a buggy or malicious middlebox or man-in-the-middle can
rewrite TCP header fields in manner that causes each endpoint
to think that the other is sending invalid TCP segments, thus
causing each side to send an unterminating stream of duplicate
acknowledgments for invalid segments.
Using 0 disables rate-limiting of dupacks in response to
invalid segments; otherwise this value specifies the minimal
space between sending such dupacks, in milliseconds.
Default: 500 (milliseconds).
tcp_keepalive_time - INTEGER
How often TCP sends out keepalive messages when keepalive is enabled.
Default: 2hours.
tcp_keepalive_probes - INTEGER
How many keepalive probes TCP sends out, until it decides that the
connection is broken. Default value: 9.
tcp_keepalive_intvl - INTEGER
How frequently the probes are send out. Multiplied by
tcp_keepalive_probes it is time to kill not responding connection,
after probes started. Default value: 75sec i.e. connection
will be aborted after ~11 minutes of retries.
tcp_l3mdev_accept - BOOLEAN
Enables child sockets to inherit the L3 master device index.
Enabling this option allows a "global" listen socket to work
across L3 master domains (e.g., VRFs) with connected sockets
derived from the listen socket to be bound to the L3 domain in
which the packets originated. Only valid when the kernel was
compiled with CONFIG_NET_L3_MASTER_DEV.
tcp_low_latency - BOOLEAN
If set, the TCP stack makes decisions that prefer lower
latency as opposed to higher throughput. By default, this
option is not set meaning that higher throughput is preferred.
An example of an application where this default should be
changed would be a Beowulf compute cluster.
Default: 0
tcp_max_orphans - INTEGER
Maximal number of TCP sockets not attached to any user file handle,
held by system. If this number is exceeded orphaned connections are
reset immediately and warning is printed. This limit exists
only to prevent simple DoS attacks, you _must_ not rely on this
or lower the limit artificially, but rather increase it
(probably, after increasing installed memory),
if network conditions require more than default value,
and tune network services to linger and kill such states
more aggressively. Let me to remind again: each orphan eats
up to ~64K of unswappable memory.
tcp_max_syn_backlog - INTEGER
Maximal number of remembered connection requests, which have not
received an acknowledgment from connecting client.
The minimal value is 128 for low memory machines, and it will
increase in proportion to the memory of machine.
If server suffers from overload, try increasing this number.
tcp_max_tw_buckets - INTEGER
Maximal number of timewait sockets held by system simultaneously.
If this number is exceeded time-wait socket is immediately destroyed
and warning is printed. This limit exists only to prevent
simple DoS attacks, you _must_ not lower the limit artificially,
but rather increase it (probably, after increasing installed memory),
if network conditions require more than default value.
tcp_mem - vector of 3 INTEGERs: min, pressure, max
min: below this number of pages TCP is not bothered about its
memory appetite.
pressure: when amount of memory allocated by TCP exceeds this number
of pages, TCP moderates its memory consumption and enters memory
pressure mode, which is exited when memory consumption falls
under "min".
max: number of pages allowed for queueing by all TCP sockets.
Defaults are calculated at boot time from amount of available
memory.
tcp_min_rtt_wlen - INTEGER
The window length of the windowed min filter to track the minimum RTT.
A shorter window lets a flow more quickly pick up new (higher)
minimum RTT when it is moved to a longer path (e.g., due to traffic
engineering). A longer window makes the filter more resistant to RTT
inflations such as transient congestion. The unit is seconds.
Default: 300
tcp_moderate_rcvbuf - BOOLEAN
If set, TCP performs receive buffer auto-tuning, attempting to
automatically size the buffer (no greater than tcp_rmem[2]) to
match the size required by the path for full throughput. Enabled by
default.
tcp_mtu_probing - INTEGER
Controls TCP Packetization-Layer Path MTU Discovery. Takes three
values:
0 - Disabled
1 - Disabled by default, enabled when an ICMP black hole detected
2 - Always enabled, use initial MSS of tcp_base_mss.
tcp_probe_interval - INTEGER
Controls how often to start TCP Packetization-Layer Path MTU
Discovery reprobe. The default is reprobing every 10 minutes as
per RFC4821.
tcp_probe_threshold - INTEGER
Controls when TCP Packetization-Layer Path MTU Discovery probing
will stop in respect to the width of search range in bytes. Default
is 8 bytes.
tcp_no_metrics_save - BOOLEAN
By default, TCP saves various connection metrics in the route cache
when the connection closes, so that connections established in the
near future can use these to set initial conditions. Usually, this
increases overall performance, but may sometimes cause performance
degradation. If set, TCP will not cache metrics on closing
connections.
tcp_orphan_retries - INTEGER
This value influences the timeout of a locally closed TCP connection,
when RTO retransmissions remain unacknowledged.
See tcp_retries2 for more details.
The default value is 8.
If your machine is a loaded WEB server,
you should think about lowering this value, such sockets
may consume significant resources. Cf. tcp_max_orphans.
tcp_recovery - INTEGER
This value is a bitmap to enable various experimental loss recovery
features.
RACK: 0x1 enables the RACK loss detection for fast detection of lost
retransmissions and tail drops.
Default: 0x1
tcp_reordering - INTEGER
Initial reordering level of packets in a TCP stream.
TCP stack can then dynamically adjust flow reordering level
between this initial value and tcp_max_reordering
Default: 3
tcp_max_reordering - INTEGER
Maximal reordering level of packets in a TCP stream.
300 is a fairly conservative value, but you might increase it
if paths are using per packet load balancing (like bonding rr mode)
Default: 300
tcp_retrans_collapse - BOOLEAN
Bug-to-bug compatibility with some broken printers.
On retransmit try to send bigger packets to work around bugs in
certain TCP stacks.
tcp_retries1 - INTEGER
This value influences the time, after which TCP decides, that
something is wrong due to unacknowledged RTO retransmissions,
and reports this suspicion to the network layer.
See tcp_retries2 for more details.
RFC 1122 recommends at least 3 retransmissions, which is the
default.
tcp_retries2 - INTEGER
This value influences the timeout of an alive TCP connection,
when RTO retransmissions remain unacknowledged.
Given a value of N, a hypothetical TCP connection following
exponential backoff with an initial RTO of TCP_RTO_MIN would
retransmit N times before killing the connection at the (N+1)th RTO.
The default value of 15 yields a hypothetical timeout of 924.6
seconds and is a lower bound for the effective timeout.
TCP will effectively time out at the first RTO which exceeds the
hypothetical timeout.
RFC 1122 recommends at least 100 seconds for the timeout,
which corresponds to a value of at least 8.
tcp_rfc1337 - BOOLEAN
If set, the TCP stack behaves conforming to RFC1337. If unset,
we are not conforming to RFC, but prevent TCP TIME_WAIT
assassination.
Default: 0
tcp_rmem - vector of 3 INTEGERs: min, default, max
min: Minimal size of receive buffer used by TCP sockets.
It is guaranteed to each TCP socket, even under moderate memory
pressure.
Default: 1 page
default: initial size of receive buffer used by TCP sockets.
This value overrides net.core.rmem_default used by other protocols.
Default: 87380 bytes. This value results in window of 65535 with
default setting of tcp_adv_win_scale and tcp_app_win:0 and a bit
less for default tcp_app_win. See below about these variables.
max: maximal size of receive buffer allowed for automatically
selected receiver buffers for TCP socket. This value does not override
net.core.rmem_max. Calling setsockopt() with SO_RCVBUF disables
automatic tuning of that socket's receive buffer size, in which
case this value is ignored.
Default: between 87380B and 6MB, depending on RAM size.
tcp_sack - BOOLEAN
Enable select acknowledgments (SACKS).
tcp_slow_start_after_idle - BOOLEAN
If set, provide RFC2861 behavior and time out the congestion
window after an idle period. An idle period is defined at
the current RTO. If unset, the congestion window will not
be timed out after an idle period.
Default: 1
tcp_stdurg - BOOLEAN
Use the Host requirements interpretation of the TCP urgent pointer field.
Most hosts use the older BSD interpretation, so if you turn this on
Linux might not communicate correctly with them.
Default: FALSE
tcp_synack_retries - INTEGER
Number of times SYNACKs for a passive TCP connection attempt will
be retransmitted. Should not be higher than 255. Default value
is 5, which corresponds to 31seconds till the last retransmission
with the current initial RTO of 1second. With this the final timeout
for a passive TCP connection will happen after 63seconds.
tcp_syncookies - BOOLEAN
Only valid when the kernel was compiled with CONFIG_SYN_COOKIES
Send out syncookies when the syn backlog queue of a socket
overflows. This is to prevent against the common 'SYN flood attack'
Default: 1
Note, that syncookies is fallback facility.
It MUST NOT be used to help highly loaded servers to stand
against legal connection rate. If you see SYN flood warnings
in your logs, but investigation shows that they occur
because of overload with legal connections, you should tune
another parameters until this warning disappear.
See: tcp_max_syn_backlog, tcp_synack_retries, tcp_abort_on_overflow.
syncookies seriously violate TCP protocol, do not allow
to use TCP extensions, can result in serious degradation
of some services (f.e. SMTP relaying), visible not by you,
but your clients and relays, contacting you. While you see
SYN flood warnings in logs not being really flooded, your server
is seriously misconfigured.
If you want to test which effects syncookies have to your
network connections you can set this knob to 2 to enable
unconditionally generation of syncookies.
tcp_fastopen - INTEGER
Enable TCP Fast Open feature (draft-ietf-tcpm-fastopen) to send data
in the opening SYN packet. To use this feature, the client application
must use sendmsg() or sendto() with MSG_FASTOPEN flag rather than
connect() to perform a TCP handshake automatically.
The values (bitmap) are
1: Enables sending data in the opening SYN on the client w/ MSG_FASTOPEN.
2: Enables TCP Fast Open on the server side, i.e., allowing data in
a SYN packet to be accepted and passed to the application before
3-way hand shake finishes.
4: Send data in the opening SYN regardless of cookie availability and
without a cookie option.
0x100: Accept SYN data w/o validating the cookie.
0x200: Accept data-in-SYN w/o any cookie option present.
0x400/0x800: Enable Fast Open on all listeners regardless of the
TCP_FASTOPEN socket option. The two different flags designate two
different ways of setting max_qlen without the TCP_FASTOPEN socket
option.
Default: 1
Note that the client & server side Fast Open flags (1 and 2
respectively) must be also enabled before the rest of flags can take
effect.
See include/net/tcp.h and the code for more details.
tcp_syn_retries - INTEGER
Number of times initial SYNs for an active TCP connection attempt
will be retransmitted. Should not be higher than 127. Default value
is 6, which corresponds to 63seconds till the last retransmission
with the current initial RTO of 1second. With this the final timeout
for an active TCP connection attempt will happen after 127seconds.
tcp_timestamps - BOOLEAN
Enable timestamps as defined in RFC1323.
tcp_min_tso_segs - INTEGER
Minimal number of segments per TSO frame.
Since linux-3.12, TCP does an automatic sizing of TSO frames,
depending on flow rate, instead of filling 64Kbytes packets.
For specific usages, it's possible to force TCP to build big
TSO frames. Note that TCP stack might split too big TSO packets
if available window is too small.
Default: 2
tcp_pacing_ss_ratio - INTEGER
sk->sk_pacing_rate is set by TCP stack using a ratio applied
to current rate. (current_rate = cwnd * mss / srtt)
If TCP is in slow start, tcp_pacing_ss_ratio is applied
to let TCP probe for bigger speeds, assuming cwnd can be
doubled every other RTT.
Default: 200
tcp_pacing_ca_ratio - INTEGER
sk->sk_pacing_rate is set by TCP stack using a ratio applied
to current rate. (current_rate = cwnd * mss / srtt)
If TCP is in congestion avoidance phase, tcp_pacing_ca_ratio
is applied to conservatively probe for bigger throughput.
Default: 120
tcp_tso_win_divisor - INTEGER
This allows control over what percentage of the congestion window
can be consumed by a single TSO frame.
The setting of this parameter is a choice between burstiness and
building larger TSO frames.
Default: 3
tcp_tw_recycle - BOOLEAN
Enable fast recycling TIME-WAIT sockets. Default value is 0.
It should not be changed without advice/request of technical
experts.
tcp_tw_reuse - BOOLEAN
Allow to reuse TIME-WAIT sockets for new connections when it is
safe from protocol viewpoint. Default value is 0.
It should not be changed without advice/request of technical
experts.
tcp_window_scaling - BOOLEAN
Enable window scaling as defined in RFC1323.
tcp_wmem - vector of 3 INTEGERs: min, default, max
min: Amount of memory reserved for send buffers for TCP sockets.
Each TCP socket has rights to use it due to fact of its birth.
Default: 1 page
default: initial size of send buffer used by TCP sockets. This
value overrides net.core.wmem_default used by other protocols.
It is usually lower than net.core.wmem_default.
Default: 16K
max: Maximal amount of memory allowed for automatically tuned
send buffers for TCP sockets. This value does not override
net.core.wmem_max. Calling setsockopt() with SO_SNDBUF disables
automatic tuning of that socket's send buffer size, in which case
this value is ignored.
Default: between 64K and 4MB, depending on RAM size.
tcp_notsent_lowat - UNSIGNED INTEGER
A TCP socket can control the amount of unsent bytes in its write queue,
thanks to TCP_NOTSENT_LOWAT socket option. poll()/select()/epoll()
reports POLLOUT events if the amount of unsent bytes is below a per
socket value, and if the write queue is not full. sendmsg() will
also not add new buffers if the limit is hit.
This global variable controls the amount of unsent data for
sockets not using TCP_NOTSENT_LOWAT. For these sockets, a change
to the global variable has immediate effect.
Default: UINT_MAX (0xFFFFFFFF)
tcp_workaround_signed_windows - BOOLEAN
If set, assume no receipt of a window scaling option means the
remote TCP is broken and treats the window as a signed quantity.
If unset, assume the remote TCP is not broken even if we do
not receive a window scaling option from them.
Default: 0
tcp_thin_linear_timeouts - BOOLEAN
Enable dynamic triggering of linear timeouts for thin streams.
If set, a check is performed upon retransmission by timeout to
determine if the stream is thin (less than 4 packets in flight).
As long as the stream is found to be thin, up to 6 linear
timeouts may be performed before exponential backoff mode is
initiated. This improves retransmission latency for
non-aggressive thin streams, often found to be time-dependent.
For more information on thin streams, see
Documentation/networking/tcp-thin.txt
Default: 0
tcp_thin_dupack - BOOLEAN
Enable dynamic triggering of retransmissions after one dupACK
for thin streams. If set, a check is performed upon reception
of a dupACK to determine if the stream is thin (less than 4
packets in flight). As long as the stream is found to be thin,
data is retransmitted on the first received dupACK. This
improves retransmission latency for non-aggressive thin
streams, often found to be time-dependent.
For more information on thin streams, see
Documentation/networking/tcp-thin.txt
Default: 0
tcp_limit_output_bytes - INTEGER
Controls TCP Small Queue limit per tcp socket.
TCP bulk sender tends to increase packets in flight until it
gets losses notifications. With SNDBUF autotuning, this can
result in a large amount of packets queued in qdisc/device
on the local machine, hurting latency of other flows, for
typical pfifo_fast qdiscs.
tcp_limit_output_bytes limits the number of bytes on qdisc
or device to reduce artificial RTT/cwnd and reduce bufferbloat.
Default: 262144
tcp_challenge_ack_limit - INTEGER
Limits number of Challenge ACK sent per second, as recommended
in RFC 5961 (Improving TCP's Robustness to Blind In-Window Attacks)
Default: 100
UDP variables:
udp_mem - vector of 3 INTEGERs: min, pressure, max
Number of pages allowed for queueing by all UDP sockets.
min: Below this number of pages UDP is not bothered about its
memory appetite. When amount of memory allocated by UDP exceeds
this number, UDP starts to moderate memory usage.
pressure: This value was introduced to follow format of tcp_mem.
max: Number of pages allowed for queueing by all UDP sockets.
Default is calculated at boot time from amount of available memory.
udp_rmem_min - INTEGER
Minimal size of receive buffer used by UDP sockets in moderation.
Each UDP socket is able to use the size for receiving data, even if
total pages of UDP sockets exceed udp_mem pressure. The unit is byte.
Default: 1 page
udp_wmem_min - INTEGER
Minimal size of send buffer used by UDP sockets in moderation.
Each UDP socket is able to use the size for sending data, even if
total pages of UDP sockets exceed udp_mem pressure. The unit is byte.
Default: 1 page
CIPSOv4 Variables:
cipso_cache_enable - BOOLEAN
If set, enable additions to and lookups from the CIPSO label mapping
cache. If unset, additions are ignored and lookups always result in a
miss. However, regardless of the setting the cache is still
invalidated when required when means you can safely toggle this on and
off and the cache will always be "safe".
Default: 1
cipso_cache_bucket_size - INTEGER
The CIPSO label cache consists of a fixed size hash table with each
hash bucket containing a number of cache entries. This variable limits
the number of entries in each hash bucket; the larger the value the
more CIPSO label mappings that can be cached. When the number of
entries in a given hash bucket reaches this limit adding new entries
causes the oldest entry in the bucket to be removed to make room.
Default: 10
cipso_rbm_optfmt - BOOLEAN
Enable the "Optimized Tag 1 Format" as defined in section 3.4.2.6 of
the CIPSO draft specification (see Documentation/netlabel for details).
This means that when set the CIPSO tag will be padded with empty
categories in order to make the packet data 32-bit aligned.
Default: 0
cipso_rbm_structvalid - BOOLEAN
If set, do a very strict check of the CIPSO option when
ip_options_compile() is called. If unset, relax the checks done during
ip_options_compile(). Either way is "safe" as errors are caught else
where in the CIPSO processing code but setting this to 0 (False) should
result in less work (i.e. it should be faster) but could cause problems
with other implementations that require strict checking.
Default: 0
IP Variables:
ip_local_port_range - 2 INTEGERS
Defines the local port range that is used by TCP and UDP to
choose the local port. The first number is the first, the
second the last local port number.
If possible, it is better these numbers have different parity.
(one even and one odd values)
The default values are 32768 and 60999 respectively.
ip_local_reserved_ports - list of comma separated ranges
Specify the ports which are reserved for known third-party
applications. These ports will not be used by automatic port
assignments (e.g. when calling connect() or bind() with port
number 0). Explicit port allocation behavior is unchanged.
The format used for both input and output is a comma separated
list of ranges (e.g. "1,2-4,10-10" for ports 1, 2, 3, 4 and
10). Writing to the file will clear all previously reserved
ports and update the current list with the one given in the
input.
Note that ip_local_port_range and ip_local_reserved_ports
settings are independent and both are considered by the kernel
when determining which ports are available for automatic port
assignments.
You can reserve ports which are not in the current
ip_local_port_range, e.g.:
$ cat /proc/sys/net/ipv4/ip_local_port_range
32000 60999
$ cat /proc/sys/net/ipv4/ip_local_reserved_ports
8080,9148
although this is redundant. However such a setting is useful
if later the port range is changed to a value that will
include the reserved ports.
Default: Empty
ip_nonlocal_bind - BOOLEAN
If set, allows processes to bind() to non-local IP addresses,
which can be quite useful - but may break some applications.
Default: 0
ip_dynaddr - BOOLEAN
If set non-zero, enables support for dynamic addresses.
If set to a non-zero value larger than 1, a kernel log
message will be printed when dynamic address rewriting
occurs.
Default: 0
ip_early_demux - BOOLEAN
Optimize input packet processing down to one demux for
certain kinds of local sockets. Currently we only do this
for established TCP sockets.
It may add an additional cost for pure routing workloads that
reduces overall throughput, in such case you should disable it.
Default: 1
icmp_echo_ignore_all - BOOLEAN
If set non-zero, then the kernel will ignore all ICMP ECHO
requests sent to it.
Default: 0
icmp_echo_ignore_broadcasts - BOOLEAN
If set non-zero, then the kernel will ignore all ICMP ECHO and
TIMESTAMP requests sent to it via broadcast/multicast.
Default: 1
icmp_ratelimit - INTEGER
Limit the maximal rates for sending ICMP packets whose type matches
icmp_ratemask (see below) to specific targets.
0 to disable any limiting,
otherwise the minimal space between responses in milliseconds.
Note that another sysctl, icmp_msgs_per_sec limits the number
of ICMP packets sent on all targets.
Default: 1000
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask (see below) are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
icmp_ratemask - INTEGER
Mask made of ICMP types for which rates are being limited.
Significant bits: IHGFEDCBA9876543210
Default mask: 0000001100000011000 (6168)
Bit definitions (see include/linux/icmp.h):
0 Echo Reply
3 Destination Unreachable *
4 Source Quench *
5 Redirect
8 Echo Request
B Time Exceeded *
C Parameter Problem *
D Timestamp Request
E Timestamp Reply
F Info Request
G Info Reply
H Address Mask Request
I Address Mask Reply
* These are rate limited by default (see default mask above)
icmp_ignore_bogus_error_responses - BOOLEAN
Some routers violate RFC1122 by sending bogus responses to broadcast
frames. Such violations are normally logged via a kernel warning.
If this is set to TRUE, the kernel will not give such warnings, which
will avoid log file clutter.
Default: 1
icmp_errors_use_inbound_ifaddr - BOOLEAN
If zero, icmp error messages are sent with the primary address of
the exiting interface.
If non-zero, the message will be sent with the primary address of
the interface that received the packet that caused the icmp error.
This is the behaviour network many administrators will expect from
a router. And it can make debugging complicated network layouts
much easier.
Note that if no primary address exists for the interface selected,
then the primary address of the first non-loopback interface that
has one will be used regardless of this setting.
Default: 0
igmp_max_memberships - INTEGER
Change the maximum number of multicast groups we can subscribe to.
Default: 20
Theoretical maximum value is bounded by having to send a membership
report in a single datagram (i.e. the report can't span multiple
datagrams, or risk confusing the switch and leaving groups you don't
intend to).
The number of supported groups 'M' is bounded by the number of group
report entries you can fit into a single datagram of 65535 bytes.
M = 65536-sizeof (ip header)/(sizeof(Group record))
Group records are variable length, with a minimum of 12 bytes.
So net.ipv4.igmp_max_memberships should not be set higher than:
(65536-24) / 12 = 5459
The value 5459 assumes no IP header options, so in practice
this number may be lower.
conf/interface/* changes special settings per interface (where
"interface" is the name of your network interface)
conf/all/* is special, changes the settings for all interfaces
igmp_qrv - INTEGER
Controls the IGMP query robustness variable (see RFC2236 8.1).
Default: 2 (as specified by RFC2236 8.1)
Minimum: 1 (as specified by RFC6636 4.5)
log_martians - BOOLEAN
Log packets with impossible addresses to kernel log.
log_martians for the interface will be enabled if at least one of
conf/{all,interface}/log_martians is set to TRUE,
it will be disabled otherwise
accept_redirects - BOOLEAN
Accept ICMP redirect messages.
accept_redirects for the interface will be enabled if:
- both conf/{all,interface}/accept_redirects are TRUE in the case
forwarding for the interface is enabled
or
- at least one of conf/{all,interface}/accept_redirects is TRUE in the
case forwarding for the interface is disabled
accept_redirects for the interface will be disabled otherwise
default TRUE (host)
FALSE (router)
forwarding - BOOLEAN
Enable IP forwarding on this interface.
mc_forwarding - BOOLEAN
Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE
and a multicast routing daemon is required.
conf/all/mc_forwarding must also be set to TRUE to enable multicast
routing for the interface
medium_id - INTEGER
Integer value used to differentiate the devices by the medium they
are attached to. Two devices can have different id values when
the broadcast packets are received only on one of them.
The default value 0 means that the device is the only interface
to its medium, value of -1 means that medium is not known.
Currently, it is used to change the proxy_arp behavior:
the proxy_arp feature is enabled for packets forwarded between
two devices attached to different media.
proxy_arp - BOOLEAN
Do proxy arp.
proxy_arp for the interface will be enabled if at least one of
conf/{all,interface}/proxy_arp is set to TRUE,
it will be disabled otherwise
proxy_arp_pvlan - BOOLEAN
Private VLAN proxy arp.
Basically allow proxy arp replies back to the same interface
(from which the ARP request/solicitation was received).
This is done to support (ethernet) switch features, like RFC
3069, where the individual ports are NOT allowed to
communicate with each other, but they are allowed to talk to
the upstream router. As described in RFC 3069, it is possible
to allow these hosts to communicate through the upstream
router by proxy_arp'ing. Don't need to be used together with
proxy_arp.
This technology is known by different names:
In RFC 3069 it is called VLAN Aggregation.
Cisco and Allied Telesyn call it Private VLAN.
Hewlett-Packard call it Source-Port filtering or port-isolation.
Ericsson call it MAC-Forced Forwarding (RFC Draft).
shared_media - BOOLEAN
Send(router) or accept(host) RFC1620 shared media redirects.
Overrides ip_secure_redirects.
shared_media for the interface will be enabled if at least one of
conf/{all,interface}/shared_media is set to TRUE,
it will be disabled otherwise
default TRUE
secure_redirects - BOOLEAN
Accept ICMP redirect messages only for gateways,
listed in default gateway list.
secure_redirects for the interface will be enabled if at least one of
conf/{all,interface}/secure_redirects is set to TRUE,
it will be disabled otherwise
default TRUE
send_redirects - BOOLEAN
Send redirects, if router.
send_redirects for the interface will be enabled if at least one of
conf/{all,interface}/send_redirects is set to TRUE,
it will be disabled otherwise
Default: TRUE
bootp_relay - BOOLEAN
Accept packets with source address 0.b.c.d destined
not to this host as local ones. It is supposed, that
BOOTP relay daemon will catch and forward such packets.
conf/all/bootp_relay must also be set to TRUE to enable BOOTP relay
for the interface
default FALSE
Not Implemented Yet.
accept_source_route - BOOLEAN
Accept packets with SRR option.
conf/all/accept_source_route must also be set to TRUE to accept packets
with SRR option on the interface
default TRUE (router)
FALSE (host)
accept_local - BOOLEAN
Accept packets with local source addresses. In combination with
suitable routing, this can be used to direct packets between two
local interfaces over the wire and have them accepted properly.
default FALSE
route_localnet - BOOLEAN
Do not consider loopback addresses as martian source or destination
while routing. This enables the use of 127/8 for local routing purposes.
default FALSE
rp_filter - INTEGER
0 - No source validation.
1 - Strict mode as defined in RFC3704 Strict Reverse Path
Each incoming packet is tested against the FIB and if the interface
is not the best reverse path the packet check will fail.
By default failed packets are discarded.
2 - Loose mode as defined in RFC3704 Loose Reverse Path
Each incoming packet's source address is also tested against the FIB
and if the source address is not reachable via any interface
the packet check will fail.
Current recommended practice in RFC3704 is to enable strict mode
to prevent IP spoofing from DDos attacks. If using asymmetric routing
or other complicated routing, then loose mode is recommended.
The max value from conf/{all,interface}/rp_filter is used
when doing source validation on the {interface}.
Default value is 0. Note that some distributions enable it
in startup scripts.
arp_filter - BOOLEAN
1 - Allows you to have multiple network interfaces on the same
subnet, and have the ARPs for each interface be answered
based on whether or not the kernel would route a packet from
the ARP'd IP out that interface (therefore you must use source
based routing for this to work). In other words it allows control
of which cards (usually 1) will respond to an arp request.
0 - (default) The kernel can respond to arp requests with addresses
from other interfaces. This may seem wrong but it usually makes
sense, because it increases the chance of successful communication.
IP addresses are owned by the complete host on Linux, not by
particular interfaces. Only for more complex setups like load-
balancing, does this behaviour cause problems.
arp_filter for the interface will be enabled if at least one of
conf/{all,interface}/arp_filter is set to TRUE,
it will be disabled otherwise
arp_announce - INTEGER
Define different restriction levels for announcing the local
source IP address from IP packets in ARP requests sent on
interface:
0 - (default) Use any local address, configured on any interface
1 - Try to avoid local addresses that are not in the target's
subnet for this interface. This mode is useful when target
hosts reachable via this interface require the source IP
address in ARP requests to be part of their logical network
configured on the receiving interface. When we generate the
request we will check all our subnets that include the
target IP and will preserve the source address if it is from
such subnet. If there is no such subnet we select source
address according to the rules for level 2.
2 - Always use the best local address for this target.
In this mode we ignore the source address in the IP packet
and try to select local address that we prefer for talks with
the target host. Such local address is selected by looking
for primary IP addresses on all our subnets on the outgoing
interface that include the target IP address. If no suitable
local address is found we select the first local address
we have on the outgoing interface or on all other interfaces,
with the hope we will receive reply for our request and
even sometimes no matter the source IP address we announce.
The max value from conf/{all,interface}/arp_announce is used.
Increasing the restriction level gives more chance for
receiving answer from the resolved target while decreasing
the level announces more valid sender's information.
arp_ignore - INTEGER
Define different modes for sending replies in response to
received ARP requests that resolve local target IP addresses:
0 - (default): reply for any local target IP address, configured
on any interface
1 - reply only if the target IP address is local address
configured on the incoming interface
2 - reply only if the target IP address is local address
configured on the incoming interface and both with the
sender's IP address are part from same subnet on this interface
3 - do not reply for local addresses configured with scope host,
only resolutions for global and link addresses are replied
4-7 - reserved
8 - do not reply for all local addresses
The max value from conf/{all,interface}/arp_ignore is used
when ARP request is received on the {interface}
arp_notify - BOOLEAN
Define mode for notification of address and device changes.
0 - (default): do nothing
1 - Generate gratuitous arp requests when device is brought up
or hardware address changes.
arp_accept - BOOLEAN
Define behavior for gratuitous ARP frames who's IP is not
already present in the ARP table:
0 - don't create new entries in the ARP table
1 - create new entries in the ARP table
Both replies and requests type gratuitous arp will trigger the
ARP table to be updated, if this setting is on.
If the ARP table already contains the IP address of the
gratuitous arp frame, the arp table will be updated regardless
if this setting is on or off.
mcast_solicit - INTEGER
The maximum number of multicast probes in INCOMPLETE state,
when the associated hardware address is unknown. Defaults
to 3.
ucast_solicit - INTEGER
The maximum number of unicast probes in PROBE state, when
the hardware address is being reconfirmed. Defaults to 3.
app_solicit - INTEGER
The maximum number of probes to send to the user space ARP daemon
via netlink before dropping back to multicast probes (see
mcast_resolicit). Defaults to 0.
mcast_resolicit - INTEGER
The maximum number of multicast probes after unicast and
app probes in PROBE state. Defaults to 0.
disable_policy - BOOLEAN
Disable IPSEC policy (SPD) for this interface
disable_xfrm - BOOLEAN
Disable IPSEC encryption on this interface, whatever the policy
igmpv2_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
IGMPv1 or IGMPv2 report retransmit will take place.
Default: 10000 (10 seconds)
igmpv3_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
IGMPv3 report retransmit will take place.
Default: 1000 (1 seconds)
promote_secondaries - BOOLEAN
When a primary IP address is removed from this interface
promote a corresponding secondary IP address instead of
removing all the corresponding secondary IP addresses.
tag - INTEGER
Allows you to write a number, which can be used as required.
Default value is 0.
xfrm4_gc_thresh - INTEGER
The threshold at which we will start garbage collecting for IPv4
destination cache entries. At twice this value the system will
refuse new allocations. The value must be set below the flowcache
limit (4096 * number of online cpus) to take effect.
igmp_link_local_mcast_reports - BOOLEAN
Enable IGMP reports for link local multicast groups in the
224.0.0.X range.
Default TRUE
Alexey Kuznetsov.
kuznet@ms2.inr.ac.ru
Updated by:
Andi Kleen
ak@muc.de
Nicolas Delon
delon.nicolas@wanadoo.fr
/proc/sys/net/ipv6/* Variables:
IPv6 has no global variables such as tcp_*. tcp_* settings under ipv4/ also
apply to IPv6 [XXX?].
bindv6only - BOOLEAN
Default value for IPV6_V6ONLY socket option,
which restricts use of the IPv6 socket to IPv6 communication
only.
TRUE: disable IPv4-mapped address feature
FALSE: enable IPv4-mapped address feature
Default: FALSE (as specified in RFC3493)
flowlabel_consistency - BOOLEAN
Protect the consistency (and unicity) of flow label.
You have to disable it to use IPV6_FL_F_REFLECT flag on the
flow label manager.
TRUE: enabled
FALSE: disabled
Default: TRUE
auto_flowlabels - INTEGER
Automatically generate flow labels based on a flow hash of the
packet. This allows intermediate devices, such as routers, to
identify packet flows for mechanisms like Equal Cost Multipath
Routing (see RFC 6438).
0: automatic flow labels are completely disabled
1: automatic flow labels are enabled by default, they can be
disabled on a per socket basis using the IPV6_AUTOFLOWLABEL
socket option
2: automatic flow labels are allowed, they may be enabled on a
per socket basis using the IPV6_AUTOFLOWLABEL socket option
3: automatic flow labels are enabled and enforced, they cannot
be disabled by the socket option
Default: 1
flowlabel_state_ranges - BOOLEAN
Split the flow label number space into two ranges. 0-0x7FFFF is
reserved for the IPv6 flow manager facility, 0x80000-0xFFFFF
is reserved for stateless flow labels as described in RFC6437.
TRUE: enabled
FALSE: disabled
Default: true
anycast_src_echo_reply - BOOLEAN
Controls the use of anycast addresses as source addresses for ICMPv6
echo reply
TRUE: enabled
FALSE: disabled
Default: FALSE
idgen_delay - INTEGER
Controls the delay in seconds after which time to retry
privacy stable address generation if a DAD conflict is
detected.
Default: 1 (as specified in RFC7217)
idgen_retries - INTEGER
Controls the number of retries to generate a stable privacy
address if a DAD conflict is detected.
Default: 3 (as specified in RFC7217)
mld_qrv - INTEGER
Controls the MLD query robustness variable (see RFC3810 9.1).
Default: 2 (as specified by RFC3810 9.1)
Minimum: 1 (as specified by RFC6636 4.5)
IPv6 Fragmentation:
ip6frag_high_thresh - INTEGER
Maximum memory used to reassemble IPv6 fragments. When
ip6frag_high_thresh bytes of memory is allocated for this purpose,
the fragment handler will toss packets until ip6frag_low_thresh
is reached.
ip6frag_low_thresh - INTEGER
See ip6frag_high_thresh
ip6frag_time - INTEGER
Time in seconds to keep an IPv6 fragment in memory.
conf/default/*:
Change the interface-specific default settings.
conf/all/*:
Change all the interface-specific settings.
[XXX: Other special features than forwarding?]
conf/all/forwarding - BOOLEAN
Enable global IPv6 forwarding between all interfaces.
IPv4 and IPv6 work differently here; e.g. netfilter must be used
to control which interfaces may forward packets and which not.
This also sets all interfaces' Host/Router setting
'forwarding' to the specified value. See below for details.
This referred to as global forwarding.
proxy_ndp - BOOLEAN
Do proxy ndp.
fwmark_reflect - BOOLEAN
Controls the fwmark of kernel-generated IPv6 reply packets that are not
associated with a socket for example, TCP RSTs or ICMPv6 echo replies).
If unset, these packets have a fwmark of zero. If set, they have the
fwmark of the packet they are replying to.
Default: 0
conf/interface/*:
Change special settings per interface.
The functional behaviour for certain settings is different
depending on whether local forwarding is enabled or not.
accept_ra - INTEGER
Accept Router Advertisements; autoconfigure using them.
It also determines whether or not to transmit Router
Solicitations. If and only if the functional setting is to
accept Router Advertisements, Router Solicitations will be
transmitted.
Possible values are:
0 Do not accept Router Advertisements.
1 Accept Router Advertisements if forwarding is disabled.
2 Overrule forwarding behaviour. Accept Router Advertisements
even if forwarding is enabled.
Functional default: enabled if local forwarding is disabled.
disabled if local forwarding is enabled.
accept_ra_defrtr - BOOLEAN
Learn default router in Router Advertisement.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_from_local - BOOLEAN
Accept RA with source-address that is found on local machine
if the RA is otherwise proper and able to be accepted.
Default is to NOT accept these as it may be an un-intended
network loop.
Functional default:
enabled if accept_ra_from_local is enabled
on a specific interface.
disabled if accept_ra_from_local is disabled
on a specific interface.
accept_ra_min_hop_limit - INTEGER
Minimum hop limit Information in Router Advertisement.
Hop limit Information in Router Advertisement less than this
variable shall be ignored.
Default: 1
accept_ra_pinfo - BOOLEAN
Learn Prefix Information in Router Advertisement.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_rt_info_max_plen - INTEGER
Maximum prefix length of Route Information in RA.
Route Information w/ prefix larger than or equal to this
variable shall be ignored.
Functional default: 0 if accept_ra_rtr_pref is enabled.
-1 if accept_ra_rtr_pref is disabled.
accept_ra_rtr_pref - BOOLEAN
Accept Router Preference in RA.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_ra_mtu - BOOLEAN
Apply the MTU value specified in RA option 5 (RFC4861). If
disabled, the MTU specified in the RA will be ignored.
Functional default: enabled if accept_ra is enabled.
disabled if accept_ra is disabled.
accept_redirects - BOOLEAN
Accept Redirects.
Functional default: enabled if local forwarding is disabled.
disabled if local forwarding is enabled.
accept_source_route - INTEGER
Accept source routing (routing extension header).
>= 0: Accept only routing header type 2.
< 0: Do not accept routing header.
Default: 0
autoconf - BOOLEAN
Autoconfigure addresses using Prefix Information in Router
Advertisements.
Functional default: enabled if accept_ra_pinfo is enabled.
disabled if accept_ra_pinfo is disabled.
dad_transmits - INTEGER
The amount of Duplicate Address Detection probes to send.
Default: 1
forwarding - INTEGER
Configure interface-specific Host/Router behaviour.
Note: It is recommended to have the same setting on all
interfaces; mixed router/host scenarios are rather uncommon.
Possible values are:
0 Forwarding disabled
1 Forwarding enabled
FALSE (0):
By default, Host behaviour is assumed. This means:
1. IsRouter flag is not set in Neighbour Advertisements.
2. If accept_ra is TRUE (default), transmit Router
Solicitations.
3. If accept_ra is TRUE (default), accept Router
Advertisements (and do autoconfiguration).
4. If accept_redirects is TRUE (default), accept Redirects.
TRUE (1):
If local forwarding is enabled, Router behaviour is assumed.
This means exactly the reverse from the above:
1. IsRouter flag is set in Neighbour Advertisements.
2. Router Solicitations are not sent unless accept_ra is 2.
3. Router Advertisements are ignored unless accept_ra is 2.
4. Redirects are ignored.
Default: 0 (disabled) if global forwarding is disabled (default),
otherwise 1 (enabled).
hop_limit - INTEGER
Default Hop Limit to set.
Default: 64
mtu - INTEGER
Default Maximum Transfer Unit
Default: 1280 (IPv6 required minimum)
ip_nonlocal_bind - BOOLEAN
If set, allows processes to bind() to non-local IPv6 addresses,
which can be quite useful - but may break some applications.
Default: 0
router_probe_interval - INTEGER
Minimum interval (in seconds) between Router Probing described
in RFC4191.
Default: 60
router_solicitation_delay - INTEGER
Number of seconds to wait after interface is brought up
before sending Router Solicitations.
Default: 1
router_solicitation_interval - INTEGER
Number of seconds to wait between Router Solicitations.
Default: 4
router_solicitations - INTEGER
Number of Router Solicitations to send until assuming no
routers are present.
Default: 3
use_oif_addrs_only - BOOLEAN
When enabled, the candidate source addresses for destinations
routed via this interface are restricted to the set of addresses
configured on this interface (vis. RFC 6724, section 4).
Default: false
use_tempaddr - INTEGER
Preference for Privacy Extensions (RFC3041).
<= 0 : disable Privacy Extensions
== 1 : enable Privacy Extensions, but prefer public
addresses over temporary addresses.
> 1 : enable Privacy Extensions and prefer temporary
addresses over public addresses.
Default: 0 (for most devices)
-1 (for point-to-point devices and loopback devices)
temp_valid_lft - INTEGER
valid lifetime (in seconds) for temporary addresses.
Default: 604800 (7 days)
temp_prefered_lft - INTEGER
Preferred lifetime (in seconds) for temporary addresses.
Default: 86400 (1 day)
max_desync_factor - INTEGER
Maximum value for DESYNC_FACTOR, which is a random value
that ensures that clients don't synchronize with each
other and generate new addresses at exactly the same time.
value is in seconds.
Default: 600
regen_max_retry - INTEGER
Number of attempts before give up attempting to generate
valid temporary addresses.
Default: 5
max_addresses - INTEGER
Maximum number of autoconfigured addresses per interface. Setting
to zero disables the limitation. It is not recommended to set this
value too large (or to zero) because it would be an easy way to
crash the kernel by allowing too many addresses to be created.
Default: 16
disable_ipv6 - BOOLEAN
Disable IPv6 operation. If accept_dad is set to 2, this value
will be dynamically set to TRUE if DAD fails for the link-local
address.
Default: FALSE (enable IPv6 operation)
When this value is changed from 1 to 0 (IPv6 is being enabled),
it will dynamically create a link-local address on the given
interface and start Duplicate Address Detection, if necessary.
When this value is changed from 0 to 1 (IPv6 is being disabled),
it will dynamically delete all address on the given interface.
accept_dad - INTEGER
Whether to accept DAD (Duplicate Address Detection).
0: Disable DAD
1: Enable DAD (default)
2: Enable DAD, and disable IPv6 operation if MAC-based duplicate
link-local address has been found.
force_tllao - BOOLEAN
Enable sending the target link-layer address option even when
responding to a unicast neighbor solicitation.
Default: FALSE
Quoting from RFC 2461, section 4.4, Target link-layer address:
"The option MUST be included for multicast solicitations in order to
avoid infinite Neighbor Solicitation "recursion" when the peer node
does not have a cache entry to return a Neighbor Advertisements
message. When responding to unicast solicitations, the option can be
omitted since the sender of the solicitation has the correct link-
layer address; otherwise it would not have be able to send the unicast
solicitation in the first place. However, including the link-layer
address in this case adds little overhead and eliminates a potential
race condition where the sender deletes the cached link-layer address
prior to receiving a response to a previous solicitation."
ndisc_notify - BOOLEAN
Define mode for notification of address and device changes.
0 - (default): do nothing
1 - Generate unsolicited neighbour advertisements when device is brought
up or hardware address changes.
mldv1_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
MLDv1 report retransmit will take place.
Default: 10000 (10 seconds)
mldv2_unsolicited_report_interval - INTEGER
The interval in milliseconds in which the next unsolicited
MLDv2 report retransmit will take place.
Default: 1000 (1 second)
force_mld_version - INTEGER
0 - (default) No enforcement of a MLD version, MLDv1 fallback allowed
1 - Enforce to use MLD version 1
2 - Enforce to use MLD version 2
suppress_frag_ndisc - INTEGER
Control RFC 6980 (Security Implications of IPv6 Fragmentation
with IPv6 Neighbor Discovery) behavior:
1 - (default) discard fragmented neighbor discovery packets
0 - allow fragmented neighbor discovery packets
optimistic_dad - BOOLEAN
Whether to perform Optimistic Duplicate Address Detection (RFC 4429).
0: disabled (default)
1: enabled
use_optimistic - BOOLEAN
If enabled, do not classify optimistic addresses as deprecated during
source address selection. Preferred addresses will still be chosen
before optimistic addresses, subject to other ranking in the source
address selection algorithm.
0: disabled (default)
1: enabled
stable_secret - IPv6 address
This IPv6 address will be used as a secret to generate IPv6
addresses for link-local addresses and autoconfigured
ones. All addresses generated after setting this secret will
be stable privacy ones by default. This can be changed via the
addrgenmode ip-link. conf/default/stable_secret is used as the
secret for the namespace, the interface specific ones can
overwrite that. Writes to conf/all/stable_secret are refused.
It is recommended to generate this secret during installation
of a system and keep it stable after that.
By default the stable secret is unset.
icmp/*:
ratelimit - INTEGER
Limit the maximal rates for sending ICMPv6 packets.
0 to disable any limiting,
otherwise the minimal space between responses in milliseconds.
Default: 1000
xfrm6_gc_thresh - INTEGER
The threshold at which we will start garbage collecting for IPv6
destination cache entries. At twice this value the system will
refuse new allocations. The value must be set below the flowcache
limit (4096 * number of online cpus) to take effect.
IPv6 Update by:
Pekka Savola <pekkas@netcore.fi>
YOSHIFUJI Hideaki / USAGI Project <yoshfuji@linux-ipv6.org>
/proc/sys/net/bridge/* Variables:
bridge-nf-call-arptables - BOOLEAN
1 : pass bridged ARP traffic to arptables' FORWARD chain.
0 : disable this.
Default: 1
bridge-nf-call-iptables - BOOLEAN
1 : pass bridged IPv4 traffic to iptables' chains.
0 : disable this.
Default: 1
bridge-nf-call-ip6tables - BOOLEAN
1 : pass bridged IPv6 traffic to ip6tables' chains.
0 : disable this.
Default: 1
bridge-nf-filter-vlan-tagged - BOOLEAN
1 : pass bridged vlan-tagged ARP/IP/IPv6 traffic to {arp,ip,ip6}tables.
0 : disable this.
Default: 0
bridge-nf-filter-pppoe-tagged - BOOLEAN
1 : pass bridged pppoe-tagged IP/IPv6 traffic to {ip,ip6}tables.
0 : disable this.
Default: 0
bridge-nf-pass-vlan-input-dev - BOOLEAN
1: if bridge-nf-filter-vlan-tagged is enabled, try to find a vlan
interface on the bridge and set the netfilter input device to the vlan.
This allows use of e.g. "iptables -i br0.1" and makes the REDIRECT
target work with vlan-on-top-of-bridge interfaces. When no matching
vlan interface is found, or this switch is off, the input device is
set to the bridge interface.
0: disable bridge netfilter vlan interface lookup.
Default: 0
proc/sys/net/sctp/* Variables:
addip_enable - BOOLEAN
Enable or disable extension of Dynamic Address Reconfiguration
(ADD-IP) functionality specified in RFC5061. This extension provides
the ability to dynamically add and remove new addresses for the SCTP
associations.
1: Enable extension.
0: Disable extension.
Default: 0
pf_enable - INTEGER
Enable or disable pf (pf is short for potentially failed) state. A value
of pf_retrans > path_max_retrans also disables pf state. That is, one of
both pf_enable and pf_retrans > path_max_retrans can disable pf state.
Since pf_retrans and path_max_retrans can be changed by userspace
application, sometimes user expects to disable pf state by the value of
pf_retrans > path_max_retrans, but occasionally the value of pf_retrans
or path_max_retrans is changed by the user application, this pf state is
enabled. As such, it is necessary to add this to dynamically enable
and disable pf state. See:
https://datatracker.ietf.org/doc/draft-ietf-tsvwg-sctp-failover for
details.
1: Enable pf.
0: Disable pf.
Default: 1
addip_noauth_enable - BOOLEAN
Dynamic Address Reconfiguration (ADD-IP) requires the use of
authentication to protect the operations of adding or removing new
addresses. This requirement is mandated so that unauthorized hosts
would not be able to hijack associations. However, older
implementations may not have implemented this requirement while
allowing the ADD-IP extension. For reasons of interoperability,
we provide this variable to control the enforcement of the
authentication requirement.
1: Allow ADD-IP extension to be used without authentication. This
should only be set in a closed environment for interoperability
with older implementations.
0: Enforce the authentication requirement
Default: 0
auth_enable - BOOLEAN
Enable or disable Authenticated Chunks extension. This extension
provides the ability to send and receive authenticated chunks and is
required for secure operation of Dynamic Address Reconfiguration
(ADD-IP) extension.
1: Enable this extension.
0: Disable this extension.
Default: 0
prsctp_enable - BOOLEAN
Enable or disable the Partial Reliability extension (RFC3758) which
is used to notify peers that a given DATA should no longer be expected.
1: Enable extension
0: Disable
Default: 1
max_burst - INTEGER
The limit of the number of new packets that can be initially sent. It
controls how bursty the generated traffic can be.
Default: 4
association_max_retrans - INTEGER
Set the maximum number for retransmissions that an association can
attempt deciding that the remote end is unreachable. If this value
is exceeded, the association is terminated.
Default: 10
max_init_retransmits - INTEGER
The maximum number of retransmissions of INIT and COOKIE-ECHO chunks
that an association will attempt before declaring the destination
unreachable and terminating.
Default: 8
path_max_retrans - INTEGER
The maximum number of retransmissions that will be attempted on a given
path. Once this threshold is exceeded, the path is considered
unreachable, and new traffic will use a different path when the
association is multihomed.
Default: 5
pf_retrans - INTEGER
The number of retransmissions that will be attempted on a given path
before traffic is redirected to an alternate transport (should one
exist). Note this is distinct from path_max_retrans, as a path that
passes the pf_retrans threshold can still be used. Its only
deprioritized when a transmission path is selected by the stack. This
setting is primarily used to enable fast failover mechanisms without
having to reduce path_max_retrans to a very low value. See:
http://www.ietf.org/id/draft-nishida-tsvwg-sctp-failover-05.txt
for details. Note also that a value of pf_retrans > path_max_retrans
disables this feature. Since both pf_retrans and path_max_retrans can
be changed by userspace application, a variable pf_enable is used to
disable pf state.
Default: 0
rto_initial - INTEGER
The initial round trip timeout value in milliseconds that will be used
in calculating round trip times. This is the initial time interval
for retransmissions.
Default: 3000
rto_max - INTEGER
The maximum value (in milliseconds) of the round trip timeout. This
is the largest time interval that can elapse between retransmissions.
Default: 60000
rto_min - INTEGER
The minimum value (in milliseconds) of the round trip timeout. This
is the smallest time interval the can elapse between retransmissions.
Default: 1000
hb_interval - INTEGER
The interval (in milliseconds) between HEARTBEAT chunks. These chunks
are sent at the specified interval on idle paths to probe the state of
a given path between 2 associations.
Default: 30000
sack_timeout - INTEGER
The amount of time (in milliseconds) that the implementation will wait
to send a SACK.
Default: 200
valid_cookie_life - INTEGER
The default lifetime of the SCTP cookie (in milliseconds). The cookie
is used during association establishment.
Default: 60000
cookie_preserve_enable - BOOLEAN
Enable or disable the ability to extend the lifetime of the SCTP cookie
that is used during the establishment phase of SCTP association
1: Enable cookie lifetime extension.
0: Disable
Default: 1
cookie_hmac_alg - STRING
Select the hmac algorithm used when generating the cookie value sent by
a listening sctp socket to a connecting client in the INIT-ACK chunk.
Valid values are:
* md5
* sha1
* none
Ability to assign md5 or sha1 as the selected alg is predicated on the
configuration of those algorithms at build time (CONFIG_CRYPTO_MD5 and
CONFIG_CRYPTO_SHA1).
Default: Dependent on configuration. MD5 if available, else SHA1 if
available, else none.
rcvbuf_policy - INTEGER
Determines if the receive buffer is attributed to the socket or to
association. SCTP supports the capability to create multiple
associations on a single socket. When using this capability, it is
possible that a single stalled association that's buffering a lot
of data may block other associations from delivering their data by
consuming all of the receive buffer space. To work around this,
the rcvbuf_policy could be set to attribute the receiver buffer space
to each association instead of the socket. This prevents the described
blocking.
1: rcvbuf space is per association
0: rcvbuf space is per socket
Default: 0
sndbuf_policy - INTEGER
Similar to rcvbuf_policy above, this applies to send buffer space.
1: Send buffer is tracked per association
0: Send buffer is tracked per socket.
Default: 0
sctp_mem - vector of 3 INTEGERs: min, pressure, max
Number of pages allowed for queueing by all SCTP sockets.
min: Below this number of pages SCTP is not bothered about its
memory appetite. When amount of memory allocated by SCTP exceeds
this number, SCTP starts to moderate memory usage.
pressure: This value was introduced to follow format of tcp_mem.
max: Number of pages allowed for queueing by all SCTP sockets.
Default is calculated at boot time from amount of available memory.
sctp_rmem - vector of 3 INTEGERs: min, default, max
Only the first value ("min") is used, "default" and "max" are
ignored.
min: Minimal size of receive buffer used by SCTP socket.
It is guaranteed to each SCTP socket (but not association) even
under moderate memory pressure.
Default: 1 page
sctp_wmem - vector of 3 INTEGERs: min, default, max
Currently this tunable has no effect.
addr_scope_policy - INTEGER
Control IPv4 address scoping - draft-stewart-tsvwg-sctp-ipv4-00
0 - Disable IPv4 address scoping
1 - Enable IPv4 address scoping
2 - Follow draft but allow IPv4 private addresses
3 - Follow draft but allow IPv4 link local addresses
Default: 1
/proc/sys/net/core/*
Please see: Documentation/sysctl/net.txt for descriptions of these entries.
/proc/sys/net/unix/*
max_dgram_qlen - INTEGER
The maximum length of dgram socket receive queue
Default: 10
UNDOCUMENTED:
/proc/sys/net/irda/*
fast_poll_increase FIXME
warn_noreply_time FIXME
discovery_slots FIXME
slot_timeout FIXME
max_baud_rate FIXME
discovery_timeout FIXME
lap_keepalive_time FIXME
max_noreply_time FIXME
max_tx_data_size FIXME
max_tx_window FIXME
min_tx_turn_time FIXME