drivers/phy/ti/phy-tusb1210.c - linux/kernel/git/paulmck/linux-rcu - Git at Google

 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * tusb1210.c - TUSB1210 USB ULPI PHY driver
  *
  * Copyright (C) 2015 Intel Corporation
  *
  * Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
  */
 #include <linux/module.h>
 #include <linux/bitfield.h>
 #include <linux/delay.h>
 #include <linux/ulpi/driver.h>
 #include <linux/ulpi/regs.h>
 #include <linux/gpio/consumer.h>
 #include <linux/phy/ulpi_phy.h>
 #include <linux/power_supply.h>
 #include <linux/workqueue.h>

 #define TUSB1211_POWER_CONTROL				0x3d
 #define TUSB1211_POWER_CONTROL_SET			0x3e
 #define TUSB1211_POWER_CONTROL_CLEAR			0x3f
 #define TUSB1211_POWER_CONTROL_SW_CONTROL		BIT(0)
 #define TUSB1211_POWER_CONTROL_DET_COMP			BIT(1)
 #define TUSB1211_POWER_CONTROL_DP_VSRC_EN		BIT(6)

 #define TUSB1210_VENDOR_SPECIFIC2			0x80
 #define TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK		GENMASK(3, 0)
 #define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK		GENMASK(5, 4)
 #define TUSB1210_VENDOR_SPECIFIC2_DP_MASK		BIT(6)

 #define TUSB1211_VENDOR_SPECIFIC3			0x85
 #define TUSB1211_VENDOR_SPECIFIC3_SET			0x86
 #define TUSB1211_VENDOR_SPECIFIC3_CLEAR			0x87
 #define TUSB1211_VENDOR_SPECIFIC3_SW_USB_DET		BIT(4)
 #define TUSB1211_VENDOR_SPECIFIC3_CHGD_IDP_SRC_EN	BIT(6)

 #define TUSB1210_RESET_TIME_MS				50

 #define TUSB1210_CHG_DET_MAX_RETRIES			5

 /* TUSB1210 charger detection work states */
 enum tusb1210_chg_det_state {
 	TUSB1210_CHG_DET_CONNECTING,
 	TUSB1210_CHG_DET_START_DET,
 	TUSB1210_CHG_DET_READ_DET,
 	TUSB1210_CHG_DET_FINISH_DET,
 	TUSB1210_CHG_DET_CONNECTED,
 	TUSB1210_CHG_DET_DISCONNECTING,
 	TUSB1210_CHG_DET_DISCONNECTING_DONE,
 	TUSB1210_CHG_DET_DISCONNECTED,
 };

 struct tusb1210 {
 	struct ulpi *ulpi;
 	struct phy *phy;
 	struct gpio_desc *gpio_reset;
 	struct gpio_desc *gpio_cs;
 	u8 otg_ctrl;
 	u8 vendor_specific2;
 #ifdef CONFIG_POWER_SUPPLY
 	enum power_supply_usb_type chg_type;
 	enum tusb1210_chg_det_state chg_det_state;
 	int chg_det_retries;
 	struct delayed_work chg_det_work;
 	struct notifier_block psy_nb;
 	struct power_supply *psy;
 	struct power_supply *charger;
 #endif
 };

 static int tusb1210_ulpi_write(struct tusb1210 *tusb, u8 reg, u8 val)
 {
 	int ret;

 	ret = ulpi_write(tusb->ulpi, reg, val);
 	if (ret)
 		dev_err(&tusb->ulpi->dev, "error %d writing val 0x%02x to reg 0x%02x\n",
 			ret, val, reg);

 	return ret;
 }

 static int tusb1210_ulpi_read(struct tusb1210 *tusb, u8 reg, u8 *val)
 {
 	int ret;

 	ret = ulpi_read(tusb->ulpi, reg);
 	if (ret >= 0) {
 		*val = ret;
 		ret = 0;
 	} else {
 		dev_err(&tusb->ulpi->dev, "error %d reading reg 0x%02x\n", ret, reg);
 	}

 	return ret;
 }

 static int tusb1210_power_on(struct phy *phy)
 {
 	struct tusb1210 *tusb = phy_get_drvdata(phy);

 	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
 	gpiod_set_value_cansleep(tusb->gpio_cs, 1);

 	msleep(TUSB1210_RESET_TIME_MS);

 	/* Restore the optional eye diagram optimization value */
 	return tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2,
 				   tusb->vendor_specific2);
 }

 static int tusb1210_power_off(struct phy *phy)
 {
 	struct tusb1210 *tusb = phy_get_drvdata(phy);

 	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
 	gpiod_set_value_cansleep(tusb->gpio_cs, 0);

 	return 0;
 }

 static int tusb1210_set_mode(struct phy *phy, enum phy_mode mode, int submode)
 {
 	struct tusb1210 *tusb = phy_get_drvdata(phy);
 	int ret;
 	u8 reg;

 	ret = tusb1210_ulpi_read(tusb, ULPI_OTG_CTRL, &reg);
 	if (ret < 0)
 		return ret;

 	switch (mode) {
 	case PHY_MODE_USB_HOST:
 		reg |= (ULPI_OTG_CTRL_DRVVBUS_EXT
 			| ULPI_OTG_CTRL_ID_PULLUP
 			| ULPI_OTG_CTRL_DP_PULLDOWN
 			| ULPI_OTG_CTRL_DM_PULLDOWN);
 		tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
 		reg |= ULPI_OTG_CTRL_DRVVBUS;
 		break;
 	case PHY_MODE_USB_DEVICE:
 		reg &= ~(ULPI_OTG_CTRL_DRVVBUS
 			 | ULPI_OTG_CTRL_DP_PULLDOWN
 			 | ULPI_OTG_CTRL_DM_PULLDOWN);
 		tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
 		reg &= ~ULPI_OTG_CTRL_DRVVBUS_EXT;
 		break;
 	default:
 		/* nothing */
 		return 0;
 	}

 	tusb->otg_ctrl = reg;
 	return tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
 }

 #ifdef CONFIG_POWER_SUPPLY
 const char * const tusb1210_chg_det_states[] = {
 	"CHG_DET_CONNECTING",
 	"CHG_DET_START_DET",
 	"CHG_DET_READ_DET",
 	"CHG_DET_FINISH_DET",
 	"CHG_DET_CONNECTED",
 	"CHG_DET_DISCONNECTING",
 	"CHG_DET_DISCONNECTING_DONE",
 	"CHG_DET_DISCONNECTED",
 };

 static void tusb1210_reset(struct tusb1210 *tusb)
 {
 	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
 	usleep_range(200, 500);
 	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
 }

 static void tusb1210_chg_det_set_type(struct tusb1210 *tusb,
 				      enum power_supply_usb_type type)
 {
 	dev_dbg(&tusb->ulpi->dev, "charger type: %d\n", type);
 	tusb->chg_type = type;
 	tusb->chg_det_retries = 0;
 	power_supply_changed(tusb->psy);
 }

 static void tusb1210_chg_det_set_state(struct tusb1210 *tusb,
 				       enum tusb1210_chg_det_state new_state,
 				       int delay_ms)
 {
 	if (delay_ms)
 		dev_dbg(&tusb->ulpi->dev, "chg_det new state %s in %d ms\n",
 			tusb1210_chg_det_states[new_state], delay_ms);

 	tusb->chg_det_state = new_state;
 	mod_delayed_work(system_long_wq, &tusb->chg_det_work,
 			 msecs_to_jiffies(delay_ms));
 }

 static void tusb1210_chg_det_handle_ulpi_error(struct tusb1210 *tusb)
 {
 	tusb1210_reset(tusb);
 	if (tusb->chg_det_retries < TUSB1210_CHG_DET_MAX_RETRIES) {
 		tusb->chg_det_retries++;
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_START_DET,
 					   TUSB1210_RESET_TIME_MS);
 	} else {
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_FINISH_DET,
 					   TUSB1210_RESET_TIME_MS);
 	}
 }

 /*
  * Boards using a TUSB121x for charger-detection have 3 power_supply class devs:
  *
  * tusb1211-charger-detect(1) -> charger -> fuel-gauge
  *
  * To determine if an USB charger is connected to the board, the online prop of
  * the charger psy needs to be read. Since the tusb1211-charger-detect psy is
  * the start of the supplier -> supplied-to chain, power_supply_am_i_supplied()
  * cannot be used here.
  *
  * Instead, below is a list of the power_supply names of known chargers for
  * these boards and the charger psy is looked up by name from this list.
  *
  * (1) modelling the external USB charger
  */
 static const char * const tusb1210_chargers[] = {
 	"bq24190-charger",
 };

 static bool tusb1210_get_online(struct tusb1210 *tusb)
 {
 	union power_supply_propval val;
 	int i;

 	for (i = 0; i < ARRAY_SIZE(tusb1210_chargers) && !tusb->charger; i++)
 		tusb->charger = power_supply_get_by_name(tusb1210_chargers[i]);

 	if (!tusb->charger)
 		return false;

 	if (power_supply_get_property(tusb->charger, POWER_SUPPLY_PROP_ONLINE, &val))
 		return false;

 	return val.intval;
 }

 static void tusb1210_chg_det_work(struct work_struct *work)
 {
 	struct tusb1210 *tusb = container_of(work, struct tusb1210, chg_det_work.work);
 	bool vbus_present = tusb1210_get_online(tusb);
 	int ret;
 	u8 val;

 	dev_dbg(&tusb->ulpi->dev, "chg_det state %s vbus_present %d\n",
 		tusb1210_chg_det_states[tusb->chg_det_state], vbus_present);

 	switch (tusb->chg_det_state) {
 	case TUSB1210_CHG_DET_CONNECTING:
 		tusb->chg_type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
 		tusb->chg_det_retries = 0;
 		/* Power on USB controller for ulpi_read()/_write() */
 		ret = pm_runtime_resume_and_get(tusb->ulpi->dev.parent);
 		if (ret < 0) {
 			dev_err(&tusb->ulpi->dev, "error %d runtime-resuming\n", ret);
 			/* Should never happen, skip charger detection */
 			tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTED, 0);
 			return;
 		}
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_START_DET, 0);
 		break;
 	case TUSB1210_CHG_DET_START_DET:
 		/*
 		 * Use the builtin charger detection FSM to keep things simple.
 		 * This only detects DCP / SDP. This is good enough for the few
 		 * boards which actually rely on the phy for charger detection.
 		 */
 		mutex_lock(&tusb->phy->mutex);
 		ret = tusb1210_ulpi_write(tusb, TUSB1211_VENDOR_SPECIFIC3_SET,
 					  TUSB1211_VENDOR_SPECIFIC3_SW_USB_DET);
 		mutex_unlock(&tusb->phy->mutex);
 		if (ret) {
 			tusb1210_chg_det_handle_ulpi_error(tusb);
 			break;
 		}

 		/* Wait 400 ms for the charger detection FSM to finish */
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_READ_DET, 400);
 		break;
 	case TUSB1210_CHG_DET_READ_DET:
 		mutex_lock(&tusb->phy->mutex);
 		ret = tusb1210_ulpi_read(tusb, TUSB1211_POWER_CONTROL, &val);
 		mutex_unlock(&tusb->phy->mutex);
 		if (ret) {
 			tusb1210_chg_det_handle_ulpi_error(tusb);
 			break;
 		}

 		if (val & TUSB1211_POWER_CONTROL_DET_COMP)
 			tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_DCP);
 		else
 			tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_SDP);

 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_FINISH_DET, 0);
 		break;
 	case TUSB1210_CHG_DET_FINISH_DET:
 		mutex_lock(&tusb->phy->mutex);

 		/* Set SW_CONTROL to stop the charger-det FSM */
 		ret = tusb1210_ulpi_write(tusb, TUSB1211_POWER_CONTROL_SET,
 					  TUSB1211_POWER_CONTROL_SW_CONTROL);

 		/* Clear DP_VSRC_EN which may have been enabled by the charger-det FSM */
 		ret |= tusb1210_ulpi_write(tusb, TUSB1211_POWER_CONTROL_CLEAR,
 					   TUSB1211_POWER_CONTROL_DP_VSRC_EN);

 		/* Clear CHGD_IDP_SRC_EN (may have been enabled by the charger-det FSM) */
 		ret |= tusb1210_ulpi_write(tusb, TUSB1211_VENDOR_SPECIFIC3_CLEAR,
 					   TUSB1211_VENDOR_SPECIFIC3_CHGD_IDP_SRC_EN);

 		/* If any of the above fails reset the phy */
 		if (ret) {
 			tusb1210_reset(tusb);
 			msleep(TUSB1210_RESET_TIME_MS);
 		}

 		/* Restore phy-parameters and OTG_CTRL register */
 		tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, tusb->otg_ctrl);
 		tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2,
 				    tusb->vendor_specific2);

 		mutex_unlock(&tusb->phy->mutex);

 		pm_runtime_put(tusb->ulpi->dev.parent);
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTED, 0);
 		break;
 	case TUSB1210_CHG_DET_CONNECTED:
 		if (!vbus_present)
 			tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTING, 0);
 		break;
 	case TUSB1210_CHG_DET_DISCONNECTING:
 		/*
 		 * The phy seems to take approx. 600ms longer then the charger
 		 * chip (which is used to get vbus_present) to determine Vbus
 		 * session end. Wait 800ms to ensure the phy has detected and
 		 * signalled Vbus session end.
 		 */
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTING_DONE, 800);
 		break;
 	case TUSB1210_CHG_DET_DISCONNECTING_DONE:
 		/*
 		 * The phy often stops reacting to ulpi_read()/_write requests
 		 * after a Vbus-session end. Reset it to work around this.
 		 */
 		tusb1210_reset(tusb);
 		tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_UNKNOWN);
 		tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTED, 0);
 		break;
 	case TUSB1210_CHG_DET_DISCONNECTED:
 		if (vbus_present)
 			tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTING, 0);
 		break;
 	}
 }

 static int tusb1210_psy_notifier(struct notifier_block *nb,
 	unsigned long event, void *ptr)
 {
 	struct tusb1210 *tusb = container_of(nb, struct tusb1210, psy_nb);
 	struct power_supply *psy = ptr;

 	if (psy != tusb->psy && psy->desc->type == POWER_SUPPLY_TYPE_USB)
 		queue_delayed_work(system_long_wq, &tusb->chg_det_work, 0);

 	return NOTIFY_OK;
 }

 static int tusb1210_psy_get_prop(struct power_supply *psy,
 				 enum power_supply_property psp,
 				 union power_supply_propval *val)
 {
 	struct tusb1210 *tusb = power_supply_get_drvdata(psy);

 	switch (psp) {
 	case POWER_SUPPLY_PROP_ONLINE:
 		val->intval = tusb1210_get_online(tusb);
 		break;
 	case POWER_SUPPLY_PROP_USB_TYPE:
 		val->intval = tusb->chg_type;
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_MAX:
 		if (tusb->chg_type == POWER_SUPPLY_USB_TYPE_DCP)
 			val->intval = 2000000;
 		else
 			val->intval = 500000;
 		break;
 	default:
 		return -EINVAL;
 	}

 	return 0;
 }

 static const enum power_supply_usb_type tusb1210_psy_usb_types[] = {
 	POWER_SUPPLY_USB_TYPE_SDP,
 	POWER_SUPPLY_USB_TYPE_DCP,
 	POWER_SUPPLY_USB_TYPE_UNKNOWN,
 };

 static const enum power_supply_property tusb1210_psy_props[] = {
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_USB_TYPE,
 	POWER_SUPPLY_PROP_CURRENT_MAX,
 };

 static const struct power_supply_desc tusb1210_psy_desc = {
 	.name = "tusb1211-charger-detect",
 	.type = POWER_SUPPLY_TYPE_USB,
 	.usb_types = tusb1210_psy_usb_types,
 	.num_usb_types = ARRAY_SIZE(tusb1210_psy_usb_types),
 	.properties = tusb1210_psy_props,
 	.num_properties = ARRAY_SIZE(tusb1210_psy_props),
 	.get_property = tusb1210_psy_get_prop,
 };

 /* Setup charger detection if requested, on errors continue without chg-det */
 static void tusb1210_probe_charger_detect(struct tusb1210 *tusb)
 {
 	struct power_supply_config psy_cfg = { .drv_data = tusb };
 	struct device *dev = &tusb->ulpi->dev;
 	int ret;

 	if (!device_property_read_bool(dev->parent, "linux,phy_charger_detect"))
 		return;

 	if (tusb->ulpi->id.product != 0x1508) {
 		dev_err(dev, "error charger detection is only supported on the TUSB1211\n");
 		return;
 	}

 	ret = tusb1210_ulpi_read(tusb, ULPI_OTG_CTRL, &tusb->otg_ctrl);
 	if (ret)
 		return;

 	tusb->psy = power_supply_register(dev, &tusb1210_psy_desc, &psy_cfg);
 	if (IS_ERR(tusb->psy))
 		return;

 	/*
 	 * Delay initial run by 2 seconds to allow the charger driver,
 	 * which is used to determine vbus_present, to load.
 	 */
 	tusb->chg_det_state = TUSB1210_CHG_DET_DISCONNECTED;
 	INIT_DELAYED_WORK(&tusb->chg_det_work, tusb1210_chg_det_work);
 	queue_delayed_work(system_long_wq, &tusb->chg_det_work, 2 * HZ);

 	tusb->psy_nb.notifier_call = tusb1210_psy_notifier;
 	power_supply_reg_notifier(&tusb->psy_nb);
 }

 static void tusb1210_remove_charger_detect(struct tusb1210 *tusb)
 {

 	if (!IS_ERR_OR_NULL(tusb->psy)) {
 		power_supply_unreg_notifier(&tusb->psy_nb);
 		cancel_delayed_work_sync(&tusb->chg_det_work);
 		power_supply_unregister(tusb->psy);
 	}

 	if (tusb->charger)
 		power_supply_put(tusb->charger);
 }
 #else
 static void tusb1210_probe_charger_detect(struct tusb1210 *tusb) { }
 static void tusb1210_remove_charger_detect(struct tusb1210 *tusb) { }
 #endif

 static const struct phy_ops phy_ops = {
 	.power_on = tusb1210_power_on,
 	.power_off = tusb1210_power_off,
 	.set_mode = tusb1210_set_mode,
 	.owner = THIS_MODULE,
 };

 static int tusb1210_probe(struct ulpi *ulpi)
 {
 	struct tusb1210 *tusb;
 	u8 val, reg;
 	int ret;

 	tusb = devm_kzalloc(&ulpi->dev, sizeof(*tusb), GFP_KERNEL);
 	if (!tusb)
 		return -ENOMEM;

 	tusb->ulpi = ulpi;

 	tusb->gpio_reset = devm_gpiod_get_optional(&ulpi->dev, "reset",
 						   GPIOD_OUT_LOW);
 	if (IS_ERR(tusb->gpio_reset))
 		return PTR_ERR(tusb->gpio_reset);

 	gpiod_set_value_cansleep(tusb->gpio_reset, 1);

 	tusb->gpio_cs = devm_gpiod_get_optional(&ulpi->dev, "cs",
 						GPIOD_OUT_LOW);
 	if (IS_ERR(tusb->gpio_cs))
 		return PTR_ERR(tusb->gpio_cs);

 	gpiod_set_value_cansleep(tusb->gpio_cs, 1);

 	/*
 	 * VENDOR_SPECIFIC2 register in TUSB1210 can be used for configuring eye
 	 * diagram optimization and DP/DM swap.
 	 */

 	ret = tusb1210_ulpi_read(tusb, TUSB1210_VENDOR_SPECIFIC2, &reg);
 	if (ret)
 		return ret;

 	/* High speed output drive strength configuration */
 	if (!device_property_read_u8(&ulpi->dev, "ihstx", &val))
 		u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK);

 	/* High speed output impedance configuration */
 	if (!device_property_read_u8(&ulpi->dev, "zhsdrv", &val))
 		u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK);

 	/* DP/DM swap control */
 	if (!device_property_read_u8(&ulpi->dev, "datapolarity", &val))
 		u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_DP_MASK);

 	ret = tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2, reg);
 	if (ret)
 		return ret;

 	tusb->vendor_specific2 = reg;

 	tusb1210_probe_charger_detect(tusb);

 	tusb->phy = ulpi_phy_create(ulpi, &phy_ops);
 	if (IS_ERR(tusb->phy))
 		return PTR_ERR(tusb->phy);

 	phy_set_drvdata(tusb->phy, tusb);
 	ulpi_set_drvdata(ulpi, tusb);
 	return 0;
 }

 static void tusb1210_remove(struct ulpi *ulpi)
 {
 	struct tusb1210 *tusb = ulpi_get_drvdata(ulpi);

 	ulpi_phy_destroy(ulpi, tusb->phy);
 	tusb1210_remove_charger_detect(tusb);
 }

 #define TI_VENDOR_ID 0x0451

 static const struct ulpi_device_id tusb1210_ulpi_id[] = {
 	{ TI_VENDOR_ID, 0x1507, },  /* TUSB1210 */
 	{ TI_VENDOR_ID, 0x1508, },  /* TUSB1211 */
 	{ },
 };
 MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id);

 static struct ulpi_driver tusb1210_driver = {
 	.id_table = tusb1210_ulpi_id,
 	.probe = tusb1210_probe,
 	.remove = tusb1210_remove,
 	.driver = {
 		.name = "tusb1210",
 		.owner = THIS_MODULE,
 	},
 };

 module_ulpi_driver(tusb1210_driver);

 MODULE_AUTHOR("Intel Corporation");
 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("TUSB1210 ULPI PHY driver");
	// SPDX-License-Identifier: GPL-2.0-only
	/*
	* tusb1210.c - TUSB1210 USB ULPI PHY driver
	*
	* Copyright (C) 2015 Intel Corporation
	*
	* Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
	*/
	#include <linux/module.h>
	#include <linux/bitfield.h>
	#include <linux/delay.h>
	#include <linux/ulpi/driver.h>
	#include <linux/ulpi/regs.h>
	#include <linux/gpio/consumer.h>
	#include <linux/phy/ulpi_phy.h>
	#include <linux/power_supply.h>
	#include <linux/workqueue.h>

	#define TUSB1211_POWER_CONTROL 0x3d
	#define TUSB1211_POWER_CONTROL_SET 0x3e
	#define TUSB1211_POWER_CONTROL_CLEAR 0x3f
	#define TUSB1211_POWER_CONTROL_SW_CONTROL BIT(0)
	#define TUSB1211_POWER_CONTROL_DET_COMP BIT(1)
	#define TUSB1211_POWER_CONTROL_DP_VSRC_EN BIT(6)

	#define TUSB1210_VENDOR_SPECIFIC2 0x80
	#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK GENMASK(3, 0)
	#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK GENMASK(5, 4)
	#define TUSB1210_VENDOR_SPECIFIC2_DP_MASK BIT(6)

	#define TUSB1211_VENDOR_SPECIFIC3 0x85
	#define TUSB1211_VENDOR_SPECIFIC3_SET 0x86
	#define TUSB1211_VENDOR_SPECIFIC3_CLEAR 0x87
	#define TUSB1211_VENDOR_SPECIFIC3_SW_USB_DET BIT(4)
	#define TUSB1211_VENDOR_SPECIFIC3_CHGD_IDP_SRC_EN BIT(6)

	#define TUSB1210_RESET_TIME_MS 50

	#define TUSB1210_CHG_DET_MAX_RETRIES 5

	/* TUSB1210 charger detection work states */
	enum tusb1210_chg_det_state {
	TUSB1210_CHG_DET_CONNECTING,
	TUSB1210_CHG_DET_START_DET,
	TUSB1210_CHG_DET_READ_DET,
	TUSB1210_CHG_DET_FINISH_DET,
	TUSB1210_CHG_DET_CONNECTED,
	TUSB1210_CHG_DET_DISCONNECTING,
	TUSB1210_CHG_DET_DISCONNECTING_DONE,
	TUSB1210_CHG_DET_DISCONNECTED,
	};

	struct tusb1210 {
	struct ulpi *ulpi;
	struct phy *phy;
	struct gpio_desc *gpio_reset;
	struct gpio_desc *gpio_cs;
	u8 otg_ctrl;
	u8 vendor_specific2;
	#ifdef CONFIG_POWER_SUPPLY
	enum power_supply_usb_type chg_type;
	enum tusb1210_chg_det_state chg_det_state;
	int chg_det_retries;
	struct delayed_work chg_det_work;
	struct notifier_block psy_nb;
	struct power_supply *psy;
	struct power_supply *charger;
	#endif
	};

	static int tusb1210_ulpi_write(struct tusb1210 *tusb, u8 reg, u8 val)
	{
	int ret;

	ret = ulpi_write(tusb->ulpi, reg, val);
	if (ret)
	dev_err(&tusb->ulpi->dev, "error %d writing val 0x%02x to reg 0x%02x\n",
	ret, val, reg);

	return ret;
	}

	static int tusb1210_ulpi_read(struct tusb1210 tusb, u8 reg, u8 val)
	{
	int ret;

	ret = ulpi_read(tusb->ulpi, reg);
	if (ret >= 0) {
	*val = ret;
	ret = 0;
	} else {
	dev_err(&tusb->ulpi->dev, "error %d reading reg 0x%02x\n", ret, reg);
	}

	return ret;
	}

	static int tusb1210_power_on(struct phy *phy)
	{
	struct tusb1210 *tusb = phy_get_drvdata(phy);

	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
	gpiod_set_value_cansleep(tusb->gpio_cs, 1);

	msleep(TUSB1210_RESET_TIME_MS);

	/* Restore the optional eye diagram optimization value */
	return tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2,
	tusb->vendor_specific2);
	}

	static int tusb1210_power_off(struct phy *phy)
	{
	struct tusb1210 *tusb = phy_get_drvdata(phy);

	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
	gpiod_set_value_cansleep(tusb->gpio_cs, 0);

	return 0;
	}

	static int tusb1210_set_mode(struct phy *phy, enum phy_mode mode, int submode)
	{
	struct tusb1210 *tusb = phy_get_drvdata(phy);
	int ret;
	u8 reg;

	ret = tusb1210_ulpi_read(tusb, ULPI_OTG_CTRL, &reg);
	if (ret < 0)
	return ret;

	switch (mode) {
	case PHY_MODE_USB_HOST:
	reg \|= (ULPI_OTG_CTRL_DRVVBUS_EXT
	\| ULPI_OTG_CTRL_ID_PULLUP
	\| ULPI_OTG_CTRL_DP_PULLDOWN
	\| ULPI_OTG_CTRL_DM_PULLDOWN);
	tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
	reg \|= ULPI_OTG_CTRL_DRVVBUS;
	break;
	case PHY_MODE_USB_DEVICE:
	reg &= ~(ULPI_OTG_CTRL_DRVVBUS
	\| ULPI_OTG_CTRL_DP_PULLDOWN
	\| ULPI_OTG_CTRL_DM_PULLDOWN);
	tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
	reg &= ~ULPI_OTG_CTRL_DRVVBUS_EXT;
	break;
	default:
	/* nothing */
	return 0;
	}

	tusb->otg_ctrl = reg;
	return tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, reg);
	}

	#ifdef CONFIG_POWER_SUPPLY
	const char * const tusb1210_chg_det_states[] = {
	"CHG_DET_CONNECTING",
	"CHG_DET_START_DET",
	"CHG_DET_READ_DET",
	"CHG_DET_FINISH_DET",
	"CHG_DET_CONNECTED",
	"CHG_DET_DISCONNECTING",
	"CHG_DET_DISCONNECTING_DONE",
	"CHG_DET_DISCONNECTED",
	};

	static void tusb1210_reset(struct tusb1210 *tusb)
	{
	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
	usleep_range(200, 500);
	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
	}

	static void tusb1210_chg_det_set_type(struct tusb1210 *tusb,
	enum power_supply_usb_type type)
	{
	dev_dbg(&tusb->ulpi->dev, "charger type: %d\n", type);
	tusb->chg_type = type;
	tusb->chg_det_retries = 0;
	power_supply_changed(tusb->psy);
	}

	static void tusb1210_chg_det_set_state(struct tusb1210 *tusb,
	enum tusb1210_chg_det_state new_state,
	int delay_ms)
	{
	if (delay_ms)
	dev_dbg(&tusb->ulpi->dev, "chg_det new state %s in %d ms\n",
	tusb1210_chg_det_states[new_state], delay_ms);

	tusb->chg_det_state = new_state;
	mod_delayed_work(system_long_wq, &tusb->chg_det_work,
	msecs_to_jiffies(delay_ms));
	}

	static void tusb1210_chg_det_handle_ulpi_error(struct tusb1210 *tusb)
	{
	tusb1210_reset(tusb);
	if (tusb->chg_det_retries < TUSB1210_CHG_DET_MAX_RETRIES) {
	tusb->chg_det_retries++;
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_START_DET,
	TUSB1210_RESET_TIME_MS);
	} else {
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_FINISH_DET,
	TUSB1210_RESET_TIME_MS);
	}
	}

	/*
	* Boards using a TUSB121x for charger-detection have 3 power_supply class devs:
	*
	* tusb1211-charger-detect(1) -> charger -> fuel-gauge
	*
	* To determine if an USB charger is connected to the board, the online prop of
	* the charger psy needs to be read. Since the tusb1211-charger-detect psy is
	* the start of the supplier -> supplied-to chain, power_supply_am_i_supplied()
	* cannot be used here.
	*
	* Instead, below is a list of the power_supply names of known chargers for
	* these boards and the charger psy is looked up by name from this list.
	*
	* (1) modelling the external USB charger
	*/
	static const char * const tusb1210_chargers[] = {
	"bq24190-charger",
	};

	static bool tusb1210_get_online(struct tusb1210 *tusb)
	{
	union power_supply_propval val;
	int i;

	for (i = 0; i < ARRAY_SIZE(tusb1210_chargers) && !tusb->charger; i++)
	tusb->charger = power_supply_get_by_name(tusb1210_chargers[i]);

	if (!tusb->charger)
	return false;

	if (power_supply_get_property(tusb->charger, POWER_SUPPLY_PROP_ONLINE, &val))
	return false;

	return val.intval;
	}

	static void tusb1210_chg_det_work(struct work_struct *work)
	{
	struct tusb1210 *tusb = container_of(work, struct tusb1210, chg_det_work.work);
	bool vbus_present = tusb1210_get_online(tusb);
	int ret;
	u8 val;

	dev_dbg(&tusb->ulpi->dev, "chg_det state %s vbus_present %d\n",
	tusb1210_chg_det_states[tusb->chg_det_state], vbus_present);

	switch (tusb->chg_det_state) {
	case TUSB1210_CHG_DET_CONNECTING:
	tusb->chg_type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
	tusb->chg_det_retries = 0;
	/* Power on USB controller for ulpi_read()/_write() */
	ret = pm_runtime_resume_and_get(tusb->ulpi->dev.parent);
	if (ret < 0) {
	dev_err(&tusb->ulpi->dev, "error %d runtime-resuming\n", ret);
	/* Should never happen, skip charger detection */
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTED, 0);
	return;
	}
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_START_DET, 0);
	break;
	case TUSB1210_CHG_DET_START_DET:
	/*
	* Use the builtin charger detection FSM to keep things simple.
	* This only detects DCP / SDP. This is good enough for the few
	* boards which actually rely on the phy for charger detection.
	*/
	mutex_lock(&tusb->phy->mutex);
	ret = tusb1210_ulpi_write(tusb, TUSB1211_VENDOR_SPECIFIC3_SET,
	TUSB1211_VENDOR_SPECIFIC3_SW_USB_DET);
	mutex_unlock(&tusb->phy->mutex);
	if (ret) {
	tusb1210_chg_det_handle_ulpi_error(tusb);
	break;
	}

	/* Wait 400 ms for the charger detection FSM to finish */
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_READ_DET, 400);
	break;
	case TUSB1210_CHG_DET_READ_DET:
	mutex_lock(&tusb->phy->mutex);
	ret = tusb1210_ulpi_read(tusb, TUSB1211_POWER_CONTROL, &val);
	mutex_unlock(&tusb->phy->mutex);
	if (ret) {
	tusb1210_chg_det_handle_ulpi_error(tusb);
	break;
	}

	if (val & TUSB1211_POWER_CONTROL_DET_COMP)
	tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_DCP);
	else
	tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_SDP);

	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_FINISH_DET, 0);
	break;
	case TUSB1210_CHG_DET_FINISH_DET:
	mutex_lock(&tusb->phy->mutex);

	/* Set SW_CONTROL to stop the charger-det FSM */
	ret = tusb1210_ulpi_write(tusb, TUSB1211_POWER_CONTROL_SET,
	TUSB1211_POWER_CONTROL_SW_CONTROL);

	/* Clear DP_VSRC_EN which may have been enabled by the charger-det FSM */
	ret \|= tusb1210_ulpi_write(tusb, TUSB1211_POWER_CONTROL_CLEAR,
	TUSB1211_POWER_CONTROL_DP_VSRC_EN);

	/* Clear CHGD_IDP_SRC_EN (may have been enabled by the charger-det FSM) */
	ret \|= tusb1210_ulpi_write(tusb, TUSB1211_VENDOR_SPECIFIC3_CLEAR,
	TUSB1211_VENDOR_SPECIFIC3_CHGD_IDP_SRC_EN);

	/* If any of the above fails reset the phy */
	if (ret) {
	tusb1210_reset(tusb);
	msleep(TUSB1210_RESET_TIME_MS);
	}

	/* Restore phy-parameters and OTG_CTRL register */
	tusb1210_ulpi_write(tusb, ULPI_OTG_CTRL, tusb->otg_ctrl);
	tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2,
	tusb->vendor_specific2);

	mutex_unlock(&tusb->phy->mutex);

	pm_runtime_put(tusb->ulpi->dev.parent);
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTED, 0);
	break;
	case TUSB1210_CHG_DET_CONNECTED:
	if (!vbus_present)
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTING, 0);
	break;
	case TUSB1210_CHG_DET_DISCONNECTING:
	/*
	* The phy seems to take approx. 600ms longer then the charger
	* chip (which is used to get vbus_present) to determine Vbus
	* session end. Wait 800ms to ensure the phy has detected and
	* signalled Vbus session end.
	*/
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTING_DONE, 800);
	break;
	case TUSB1210_CHG_DET_DISCONNECTING_DONE:
	/*
	* The phy often stops reacting to ulpi_read()/_write requests
	* after a Vbus-session end. Reset it to work around this.
	*/
	tusb1210_reset(tusb);
	tusb1210_chg_det_set_type(tusb, POWER_SUPPLY_USB_TYPE_UNKNOWN);
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_DISCONNECTED, 0);
	break;
	case TUSB1210_CHG_DET_DISCONNECTED:
	if (vbus_present)
	tusb1210_chg_det_set_state(tusb, TUSB1210_CHG_DET_CONNECTING, 0);
	break;
	}
	}

	static int tusb1210_psy_notifier(struct notifier_block *nb,
	unsigned long event, void *ptr)
	{
	struct tusb1210 *tusb = container_of(nb, struct tusb1210, psy_nb);
	struct power_supply *psy = ptr;

	if (psy != tusb->psy && psy->desc->type == POWER_SUPPLY_TYPE_USB)
	queue_delayed_work(system_long_wq, &tusb->chg_det_work, 0);

	return NOTIFY_OK;
	}

	static int tusb1210_psy_get_prop(struct power_supply *psy,
	enum power_supply_property psp,
	union power_supply_propval *val)
	{
	struct tusb1210 *tusb = power_supply_get_drvdata(psy);

	switch (psp) {
	case POWER_SUPPLY_PROP_ONLINE:
	val->intval = tusb1210_get_online(tusb);
	break;
	case POWER_SUPPLY_PROP_USB_TYPE:
	val->intval = tusb->chg_type;
	break;
	case POWER_SUPPLY_PROP_CURRENT_MAX:
	if (tusb->chg_type == POWER_SUPPLY_USB_TYPE_DCP)
	val->intval = 2000000;
	else
	val->intval = 500000;
	break;
	default:
	return -EINVAL;
	}

	return 0;
	}

	static const enum power_supply_usb_type tusb1210_psy_usb_types[] = {
	POWER_SUPPLY_USB_TYPE_SDP,
	POWER_SUPPLY_USB_TYPE_DCP,
	POWER_SUPPLY_USB_TYPE_UNKNOWN,
	};

	static const enum power_supply_property tusb1210_psy_props[] = {
	POWER_SUPPLY_PROP_ONLINE,
	POWER_SUPPLY_PROP_USB_TYPE,
	POWER_SUPPLY_PROP_CURRENT_MAX,
	};

	static const struct power_supply_desc tusb1210_psy_desc = {
	.name = "tusb1211-charger-detect",
	.type = POWER_SUPPLY_TYPE_USB,
	.usb_types = tusb1210_psy_usb_types,
	.num_usb_types = ARRAY_SIZE(tusb1210_psy_usb_types),
	.properties = tusb1210_psy_props,
	.num_properties = ARRAY_SIZE(tusb1210_psy_props),
	.get_property = tusb1210_psy_get_prop,
	};

	/* Setup charger detection if requested, on errors continue without chg-det */
	static void tusb1210_probe_charger_detect(struct tusb1210 *tusb)
	{
	struct power_supply_config psy_cfg = { .drv_data = tusb };
	struct device *dev = &tusb->ulpi->dev;
	int ret;

	if (!device_property_read_bool(dev->parent, "linux,phy_charger_detect"))
	return;

	if (tusb->ulpi->id.product != 0x1508) {
	dev_err(dev, "error charger detection is only supported on the TUSB1211\n");
	return;
	}

	ret = tusb1210_ulpi_read(tusb, ULPI_OTG_CTRL, &tusb->otg_ctrl);
	if (ret)
	return;

	tusb->psy = power_supply_register(dev, &tusb1210_psy_desc, &psy_cfg);
	if (IS_ERR(tusb->psy))
	return;

	/*
	* Delay initial run by 2 seconds to allow the charger driver,
	* which is used to determine vbus_present, to load.
	*/
	tusb->chg_det_state = TUSB1210_CHG_DET_DISCONNECTED;
	INIT_DELAYED_WORK(&tusb->chg_det_work, tusb1210_chg_det_work);
	queue_delayed_work(system_long_wq, &tusb->chg_det_work, 2 * HZ);

	tusb->psy_nb.notifier_call = tusb1210_psy_notifier;
	power_supply_reg_notifier(&tusb->psy_nb);
	}

	static void tusb1210_remove_charger_detect(struct tusb1210 *tusb)
	{

	if (!IS_ERR_OR_NULL(tusb->psy)) {
	power_supply_unreg_notifier(&tusb->psy_nb);
	cancel_delayed_work_sync(&tusb->chg_det_work);
	power_supply_unregister(tusb->psy);
	}

	if (tusb->charger)
	power_supply_put(tusb->charger);
	}
	#else
	static void tusb1210_probe_charger_detect(struct tusb1210 *tusb) { }
	static void tusb1210_remove_charger_detect(struct tusb1210 *tusb) { }
	#endif

	static const struct phy_ops phy_ops = {
	.power_on = tusb1210_power_on,
	.power_off = tusb1210_power_off,
	.set_mode = tusb1210_set_mode,
	.owner = THIS_MODULE,
	};

	static int tusb1210_probe(struct ulpi *ulpi)
	{
	struct tusb1210 *tusb;
	u8 val, reg;
	int ret;

	tusb = devm_kzalloc(&ulpi->dev, sizeof(*tusb), GFP_KERNEL);
	if (!tusb)
	return -ENOMEM;

	tusb->ulpi = ulpi;

	tusb->gpio_reset = devm_gpiod_get_optional(&ulpi->dev, "reset",
	GPIOD_OUT_LOW);
	if (IS_ERR(tusb->gpio_reset))
	return PTR_ERR(tusb->gpio_reset);

	gpiod_set_value_cansleep(tusb->gpio_reset, 1);

	tusb->gpio_cs = devm_gpiod_get_optional(&ulpi->dev, "cs",
	GPIOD_OUT_LOW);
	if (IS_ERR(tusb->gpio_cs))
	return PTR_ERR(tusb->gpio_cs);

	gpiod_set_value_cansleep(tusb->gpio_cs, 1);

	/*
	* VENDOR_SPECIFIC2 register in TUSB1210 can be used for configuring eye
	* diagram optimization and DP/DM swap.
	*/

	ret = tusb1210_ulpi_read(tusb, TUSB1210_VENDOR_SPECIFIC2, &reg);
	if (ret)
	return ret;

	/* High speed output drive strength configuration */
	if (!device_property_read_u8(&ulpi->dev, "ihstx", &val))
	u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK);

	/* High speed output impedance configuration */
	if (!device_property_read_u8(&ulpi->dev, "zhsdrv", &val))
	u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK);

	/* DP/DM swap control */
	if (!device_property_read_u8(&ulpi->dev, "datapolarity", &val))
	u8p_replace_bits(&reg, val, (u8)TUSB1210_VENDOR_SPECIFIC2_DP_MASK);

	ret = tusb1210_ulpi_write(tusb, TUSB1210_VENDOR_SPECIFIC2, reg);
	if (ret)
	return ret;

	tusb->vendor_specific2 = reg;

	tusb1210_probe_charger_detect(tusb);

	tusb->phy = ulpi_phy_create(ulpi, &phy_ops);
	if (IS_ERR(tusb->phy))
	return PTR_ERR(tusb->phy);

	phy_set_drvdata(tusb->phy, tusb);
	ulpi_set_drvdata(ulpi, tusb);
	return 0;
	}

	static void tusb1210_remove(struct ulpi *ulpi)
	{
	struct tusb1210 *tusb = ulpi_get_drvdata(ulpi);

	ulpi_phy_destroy(ulpi, tusb->phy);
	tusb1210_remove_charger_detect(tusb);
	}

	#define TI_VENDOR_ID 0x0451

	static const struct ulpi_device_id tusb1210_ulpi_id[] = {
	{ TI_VENDOR_ID, 0x1507, }, /* TUSB1210 */
	{ TI_VENDOR_ID, 0x1508, }, /* TUSB1211 */
	{ },
	};
	MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id);

	static struct ulpi_driver tusb1210_driver = {
	.id_table = tusb1210_ulpi_id,
	.probe = tusb1210_probe,
	.remove = tusb1210_remove,
	.driver = {
	.name = "tusb1210",
	.owner = THIS_MODULE,
	},
	};

	module_ulpi_driver(tusb1210_driver);

	MODULE_AUTHOR("Intel Corporation");
	MODULE_LICENSE("GPL v2");
	MODULE_DESCRIPTION("TUSB1210 ULPI PHY driver");