| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (c) 2023 - 2025 Intel Corporation. |
| |
| #include <linux/acpi.h> |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regmap.h> |
| #include <linux/v4l2-dv-timings.h> |
| |
| #include <media/v4l2-cci.h> |
| #include <media/v4l2-ctrls.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-dv-timings.h> |
| #include <media/v4l2-event.h> |
| #include <media/v4l2-fwnode.h> |
| |
| #define LT6911UXE_CHIP_ID 0x2102 |
| #define REG_CHIP_ID CCI_REG16(0xe100) |
| |
| #define REG_ENABLE_I2C CCI_REG8(0xe0ee) |
| #define REG_HALF_PIX_CLK CCI_REG24(0xe085) |
| #define REG_BYTE_CLK CCI_REG24(0xe092) |
| #define REG_HALF_H_TOTAL CCI_REG16(0xe088) |
| #define REG_V_TOTAL CCI_REG16(0xe08a) |
| #define REG_HALF_H_ACTIVE CCI_REG16(0xe08c) |
| #define REG_V_ACTIVE CCI_REG16(0xe08e) |
| #define REG_MIPI_FORMAT CCI_REG8(0xe096) |
| #define REG_MIPI_TX_CTRL CCI_REG8(0xe0b0) |
| |
| /* Interrupts */ |
| #define REG_INT_HDMI CCI_REG8(0xe084) |
| #define INT_VIDEO_DISAPPEAR 0x0 |
| #define INT_VIDEO_READY 0x1 |
| |
| #define LT6911UXE_DEFAULT_LANES 4 |
| #define LT6911_PAGE_CONTROL 0xff |
| #define YUV422_8_BIT 0x7 |
| |
| static const struct v4l2_dv_timings_cap lt6911uxe_timings_cap_4kp30 = { |
| .type = V4L2_DV_BT_656_1120, |
| /* keep this initialization for compatibility with CLANG */ |
| .reserved = { 0 }, |
| /* Pixel clock from REF_01 p. 20. Min/max height/width are unknown */ |
| V4L2_INIT_BT_TIMINGS(160, 3840, /* min/max width */ |
| 120, 2160, /* min/max height */ |
| 50000000, 594000000, /* min/max pixelclock */ |
| V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | |
| V4L2_DV_BT_STD_CVT, |
| V4L2_DV_BT_CAP_PROGRESSIVE | |
| V4L2_DV_BT_CAP_CUSTOM | |
| V4L2_DV_BT_CAP_REDUCED_BLANKING) |
| }; |
| |
| static const struct regmap_range_cfg lt6911uxe_ranges[] = { |
| { |
| .name = "register_range", |
| .range_min = 0, |
| .range_max = 0xffff, |
| .selector_reg = LT6911_PAGE_CONTROL, |
| .selector_mask = 0xff, |
| .selector_shift = 0, |
| .window_start = 0, |
| .window_len = 0x100, |
| }, |
| }; |
| |
| static const struct regmap_config lt6911uxe_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = 0xffff, |
| .ranges = lt6911uxe_ranges, |
| .num_ranges = ARRAY_SIZE(lt6911uxe_ranges), |
| }; |
| |
| struct lt6911uxe_mode { |
| u32 width; |
| u32 height; |
| u32 htotal; |
| u32 vtotal; |
| u32 code; |
| u32 fps; |
| u32 lanes; |
| s64 link_freq; |
| u64 pixel_clk; |
| }; |
| |
| struct lt6911uxe { |
| struct v4l2_subdev sd; |
| struct media_pad pad; |
| struct v4l2_ctrl_handler ctrl_handler; |
| struct v4l2_ctrl *pixel_rate; |
| struct v4l2_dv_timings timings; |
| struct lt6911uxe_mode cur_mode; |
| struct regmap *regmap; |
| struct gpio_desc *reset_gpio; |
| struct gpio_desc *irq_gpio; |
| }; |
| |
| static const struct v4l2_event lt6911uxe_ev_source_change = { |
| .type = V4L2_EVENT_SOURCE_CHANGE, |
| .u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION, |
| }; |
| |
| static inline struct lt6911uxe *to_lt6911uxe(struct v4l2_subdev *sd) |
| { |
| return container_of(sd, struct lt6911uxe, sd); |
| } |
| |
| static s64 get_pixel_rate(struct lt6911uxe *lt6911uxe) |
| { |
| s64 pixel_rate; |
| |
| pixel_rate = (s64)lt6911uxe->cur_mode.width * |
| lt6911uxe->cur_mode.height * |
| lt6911uxe->cur_mode.fps * 16; |
| do_div(pixel_rate, lt6911uxe->cur_mode.lanes); |
| |
| return pixel_rate; |
| } |
| |
| static int lt6911uxe_get_detected_timings(struct v4l2_subdev *sd, |
| struct v4l2_dv_timings *timings) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct v4l2_bt_timings *bt = &timings->bt; |
| |
| memset(timings, 0, sizeof(struct v4l2_dv_timings)); |
| |
| timings->type = V4L2_DV_BT_656_1120; |
| |
| bt->width = lt6911uxe->cur_mode.width; |
| bt->height = lt6911uxe->cur_mode.height; |
| bt->vsync = lt6911uxe->cur_mode.vtotal - lt6911uxe->cur_mode.height; |
| bt->hsync = lt6911uxe->cur_mode.htotal - lt6911uxe->cur_mode.width; |
| bt->pixelclock = lt6911uxe->cur_mode.pixel_clk; |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_s_dv_timings(struct v4l2_subdev *sd, unsigned int pad, |
| struct v4l2_dv_timings *timings) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct v4l2_subdev_state *state; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| if (v4l2_match_dv_timings(<6911uxe->timings, timings, 0, false)) { |
| v4l2_subdev_unlock_state(state); |
| return 0; |
| } |
| |
| if (!v4l2_valid_dv_timings(timings, <6911uxe_timings_cap_4kp30, |
| NULL, NULL)) { |
| v4l2_subdev_unlock_state(state); |
| return -ERANGE; |
| } |
| lt6911uxe->timings = *timings; |
| v4l2_subdev_unlock_state(state); |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_g_dv_timings(struct v4l2_subdev *sd, unsigned int pad, |
| struct v4l2_dv_timings *timings) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct v4l2_subdev_state *state; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| |
| *timings = lt6911uxe->timings; |
| v4l2_subdev_unlock_state(state); |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_query_dv_timings(struct v4l2_subdev *sd, unsigned int pad, |
| struct v4l2_dv_timings *timings) |
| { |
| struct v4l2_subdev_state *state; |
| int ret; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| ret = lt6911uxe_get_detected_timings(sd, timings); |
| if (ret) { |
| v4l2_subdev_unlock_state(state); |
| return ret; |
| } |
| |
| if (!v4l2_valid_dv_timings(timings, <6911uxe_timings_cap_4kp30, |
| NULL, NULL)) { |
| v4l2_subdev_unlock_state(state); |
| return -ERANGE; |
| } |
| |
| v4l2_subdev_unlock_state(state); |
| return 0; |
| } |
| |
| static int lt6911uxe_enum_dv_timings(struct v4l2_subdev *sd, |
| struct v4l2_enum_dv_timings *timings) |
| { |
| return v4l2_enum_dv_timings_cap(timings, |
| <6911uxe_timings_cap_4kp30, NULL, NULL); |
| } |
| |
| static int lt6911uxe_dv_timings_cap(struct v4l2_subdev *sd, |
| struct v4l2_dv_timings_cap *cap) |
| { |
| *cap = lt6911uxe_timings_cap_4kp30; |
| return 0; |
| } |
| |
| static int lt6911uxe_status_update(struct lt6911uxe *lt6911uxe) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(<6911uxe->sd); |
| u64 int_event; |
| u64 byte_clk, half_pix_clk, fps, format; |
| u64 half_htotal, vtotal, half_width, height; |
| int ret = 0; |
| |
| /* Read interrupt event */ |
| cci_read(lt6911uxe->regmap, REG_INT_HDMI, &int_event, &ret); |
| if (ret) { |
| dev_err(&client->dev, "failed to read interrupt event: %d\n", |
| ret); |
| return ret; |
| } |
| |
| switch (int_event) { |
| case INT_VIDEO_READY: |
| cci_read(lt6911uxe->regmap, REG_BYTE_CLK, &byte_clk, &ret); |
| byte_clk *= 1000; |
| cci_read(lt6911uxe->regmap, REG_HALF_PIX_CLK, |
| &half_pix_clk, &ret); |
| half_pix_clk *= 1000; |
| |
| if (ret || byte_clk == 0 || half_pix_clk == 0) { |
| dev_dbg(&client->dev, |
| "invalid ByteClock or PixelClock\n"); |
| return -EINVAL; |
| } |
| |
| cci_read(lt6911uxe->regmap, REG_HALF_H_TOTAL, |
| &half_htotal, &ret); |
| cci_read(lt6911uxe->regmap, REG_V_TOTAL, &vtotal, &ret); |
| if (ret || half_htotal == 0 || vtotal == 0) { |
| dev_dbg(&client->dev, "invalid htotal or vtotal\n"); |
| return -EINVAL; |
| } |
| |
| fps = div_u64(half_pix_clk, half_htotal * vtotal); |
| if (fps > 60) { |
| dev_dbg(&client->dev, |
| "max fps is 60, current fps: %llu\n", fps); |
| return -EINVAL; |
| } |
| |
| cci_read(lt6911uxe->regmap, REG_HALF_H_ACTIVE, |
| &half_width, &ret); |
| cci_read(lt6911uxe->regmap, REG_V_ACTIVE, &height, &ret); |
| if (ret || half_width == 0 || half_width * 2 > 3840 || |
| height == 0 || height > 2160) { |
| dev_dbg(&client->dev, "invalid width or height\n"); |
| return -EINVAL; |
| } |
| |
| /* |
| * Get MIPI format, YUV422_8_BIT is expected in lt6911uxe |
| */ |
| cci_read(lt6911uxe->regmap, REG_MIPI_FORMAT, &format, &ret); |
| if (format != YUV422_8_BIT) { |
| dev_dbg(&client->dev, "invalid MIPI format\n"); |
| return -EINVAL; |
| } |
| |
| lt6911uxe->cur_mode.height = height; |
| lt6911uxe->cur_mode.width = half_width * 2; |
| lt6911uxe->cur_mode.fps = fps; |
| /* MIPI Clock Rate = ByteClock × 4, defined in lt6911uxe spec */ |
| lt6911uxe->cur_mode.link_freq = byte_clk * 4; |
| lt6911uxe->cur_mode.pixel_clk = half_pix_clk * 2; |
| lt6911uxe->cur_mode.vtotal = vtotal; |
| lt6911uxe->cur_mode.htotal = half_htotal * 2; |
| break; |
| |
| case INT_VIDEO_DISAPPEAR: |
| cci_write(lt6911uxe->regmap, REG_MIPI_TX_CTRL, 0x0, &ret); |
| lt6911uxe->cur_mode.height = 0; |
| lt6911uxe->cur_mode.width = 0; |
| lt6911uxe->cur_mode.fps = 0; |
| lt6911uxe->cur_mode.link_freq = 0; |
| break; |
| |
| default: |
| ret = -ENOLINK; |
| } |
| v4l2_subdev_notify_event(<6911uxe->sd, <6911uxe_ev_source_change); |
| return ret; |
| } |
| |
| static int lt6911uxe_init_controls(struct lt6911uxe *lt6911uxe) |
| { |
| struct v4l2_ctrl_handler *ctrl_hdlr; |
| s64 pixel_rate; |
| int ret; |
| |
| ctrl_hdlr = <6911uxe->ctrl_handler; |
| ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8); |
| if (ret) |
| return ret; |
| |
| pixel_rate = get_pixel_rate(lt6911uxe); |
| lt6911uxe->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, NULL, |
| V4L2_CID_PIXEL_RATE, |
| pixel_rate, pixel_rate, 1, |
| pixel_rate); |
| |
| if (ctrl_hdlr->error) { |
| ret = ctrl_hdlr->error; |
| goto hdlr_free; |
| } |
| lt6911uxe->sd.ctrl_handler = ctrl_hdlr; |
| |
| return 0; |
| |
| hdlr_free: |
| v4l2_ctrl_handler_free(ctrl_hdlr); |
| return ret; |
| } |
| |
| static void lt6911uxe_update_pad_format(const struct lt6911uxe_mode *mode, |
| struct v4l2_mbus_framefmt *fmt) |
| { |
| fmt->width = mode->width; |
| fmt->height = mode->height; |
| fmt->code = mode->code; |
| fmt->field = V4L2_FIELD_NONE; |
| } |
| |
| static int lt6911uxe_enable_streams(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, |
| u32 pad, u64 streams_mask) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(sd); |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| int ret; |
| |
| ret = pm_runtime_resume_and_get(&client->dev); |
| if (ret < 0) |
| return ret; |
| |
| cci_write(lt6911uxe->regmap, REG_MIPI_TX_CTRL, 0x1, &ret); |
| if (ret) { |
| dev_err(&client->dev, "failed to start stream: %d\n", ret); |
| goto err_rpm_put; |
| } |
| |
| return 0; |
| |
| err_rpm_put: |
| pm_runtime_put(&client->dev); |
| return ret; |
| } |
| |
| static int lt6911uxe_disable_streams(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, |
| u32 pad, u64 streams_mask) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct i2c_client *client = v4l2_get_subdevdata(<6911uxe->sd); |
| int ret; |
| |
| ret = cci_write(lt6911uxe->regmap, REG_MIPI_TX_CTRL, 0x0, NULL); |
| if (ret) |
| dev_err(&client->dev, "failed to stop stream: %d\n", ret); |
| |
| pm_runtime_put(&client->dev); |
| return 0; |
| } |
| |
| static int lt6911uxe_set_format(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *fmt) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| u64 pixel_rate; |
| |
| lt6911uxe_update_pad_format(<6911uxe->cur_mode, &fmt->format); |
| *v4l2_subdev_state_get_format(sd_state, fmt->pad) = fmt->format; |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) |
| return 0; |
| |
| pixel_rate = get_pixel_rate(lt6911uxe); |
| __v4l2_ctrl_modify_range(lt6911uxe->pixel_rate, pixel_rate, |
| pixel_rate, 1, pixel_rate); |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_enum_mbus_code(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_mbus_code_enum *code) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| |
| if (code->index) |
| return -EINVAL; |
| |
| code->code = lt6911uxe->cur_mode.code; |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_get_mbus_config(struct v4l2_subdev *sd, |
| unsigned int pad, |
| struct v4l2_mbus_config *cfg) |
| { |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct v4l2_subdev_state *state; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| cfg->type = V4L2_MBUS_CSI2_DPHY; |
| cfg->link_freq = lt6911uxe->cur_mode.link_freq; |
| v4l2_subdev_unlock_state(state); |
| |
| return 0; |
| } |
| |
| static int lt6911uxe_init_state(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state) |
| { |
| struct v4l2_subdev_format fmt = { |
| .which = sd_state ? V4L2_SUBDEV_FORMAT_TRY |
| : V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| |
| return lt6911uxe_set_format(sd, sd_state, &fmt); |
| } |
| |
| static const struct v4l2_subdev_video_ops lt6911uxe_video_ops = { |
| .s_stream = v4l2_subdev_s_stream_helper, |
| }; |
| |
| /* |
| * lt6911uxe provides editable EDID for customers, but only can be edited like |
| * updating flash. Due to this limitation, it is not possible to implement |
| * EDID support. |
| */ |
| static const struct v4l2_subdev_pad_ops lt6911uxe_pad_ops = { |
| .set_fmt = lt6911uxe_set_format, |
| .get_fmt = v4l2_subdev_get_fmt, |
| .enable_streams = lt6911uxe_enable_streams, |
| .disable_streams = lt6911uxe_disable_streams, |
| .enum_mbus_code = lt6911uxe_enum_mbus_code, |
| .get_frame_interval = v4l2_subdev_get_frame_interval, |
| .s_dv_timings = lt6911uxe_s_dv_timings, |
| .g_dv_timings = lt6911uxe_g_dv_timings, |
| .query_dv_timings = lt6911uxe_query_dv_timings, |
| .enum_dv_timings = lt6911uxe_enum_dv_timings, |
| .dv_timings_cap = lt6911uxe_dv_timings_cap, |
| .get_mbus_config = lt6911uxe_get_mbus_config, |
| }; |
| |
| static const struct v4l2_subdev_core_ops lt6911uxe_subdev_core_ops = { |
| .subscribe_event = v4l2_ctrl_subdev_subscribe_event, |
| .unsubscribe_event = v4l2_event_subdev_unsubscribe, |
| }; |
| |
| static const struct v4l2_subdev_ops lt6911uxe_subdev_ops = { |
| .core = <6911uxe_subdev_core_ops, |
| .video = <6911uxe_video_ops, |
| .pad = <6911uxe_pad_ops, |
| }; |
| |
| static const struct media_entity_operations lt6911uxe_subdev_entity_ops = { |
| .link_validate = v4l2_subdev_link_validate, |
| }; |
| |
| static const struct v4l2_subdev_internal_ops lt6911uxe_internal_ops = { |
| .init_state = lt6911uxe_init_state, |
| }; |
| |
| static int lt6911uxe_fwnode_parse(struct lt6911uxe *lt6911uxe, |
| struct device *dev) |
| { |
| struct fwnode_handle *endpoint; |
| struct v4l2_fwnode_endpoint bus_cfg = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY, |
| }; |
| int ret; |
| |
| endpoint = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), 0, 0, |
| FWNODE_GRAPH_ENDPOINT_NEXT); |
| if (!endpoint) |
| return dev_err_probe(dev, -EPROBE_DEFER, |
| "endpoint node not found\n"); |
| |
| ret = v4l2_fwnode_endpoint_parse(endpoint, &bus_cfg); |
| fwnode_handle_put(endpoint); |
| if (ret) { |
| dev_err(dev, "failed to parse endpoint node: %d\n", ret); |
| goto out_err; |
| } |
| |
| /* |
| * Check the number of MIPI CSI2 data lanes, |
| * lt6911uxe only support 4 lanes. |
| */ |
| if (bus_cfg.bus.mipi_csi2.num_data_lanes != LT6911UXE_DEFAULT_LANES) { |
| dev_err(dev, "only 4 data lanes are currently supported\n"); |
| ret = -EINVAL; |
| goto out_err; |
| } |
| lt6911uxe->cur_mode.lanes = bus_cfg.bus.mipi_csi2.num_data_lanes; |
| lt6911uxe->cur_mode.code = MEDIA_BUS_FMT_UYVY8_1X16; |
| |
| return 0; |
| |
| out_err: |
| v4l2_fwnode_endpoint_free(&bus_cfg); |
| return ret; |
| } |
| |
| static int lt6911uxe_identify_module(struct lt6911uxe *lt6911uxe, |
| struct device *dev) |
| { |
| u64 val; |
| int ret = 0; |
| |
| /* Chip ID should be confirmed when the I2C slave is active */ |
| cci_write(lt6911uxe->regmap, REG_ENABLE_I2C, 0x1, &ret); |
| cci_read(lt6911uxe->regmap, REG_CHIP_ID, &val, &ret); |
| cci_write(lt6911uxe->regmap, REG_ENABLE_I2C, 0x0, &ret); |
| if (ret) |
| return dev_err_probe(dev, ret, "fail to read chip id\n"); |
| |
| if (val != LT6911UXE_CHIP_ID) { |
| return dev_err_probe(dev, -ENXIO, "chip id mismatch: %x!=%x\n", |
| LT6911UXE_CHIP_ID, (u16)val); |
| } |
| |
| return 0; |
| } |
| |
| static irqreturn_t lt6911uxe_threaded_irq_fn(int irq, void *dev_id) |
| { |
| struct v4l2_subdev *sd = dev_id; |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| struct v4l2_subdev_state *state; |
| struct v4l2_subdev_format fmt = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE |
| }; |
| |
| lt6911uxe_status_update(lt6911uxe); |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| /* |
| * As a HDMI to CSI2 bridge, it needs to update the format in time |
| * when the HDMI source changes. |
| */ |
| lt6911uxe_set_format(sd, state, &fmt); |
| v4l2_subdev_unlock_state(state); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void lt6911uxe_remove(struct i2c_client *client) |
| { |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct lt6911uxe *lt6911uxe = to_lt6911uxe(sd); |
| |
| free_irq(gpiod_to_irq(lt6911uxe->irq_gpio), lt6911uxe); |
| v4l2_async_unregister_subdev(sd); |
| v4l2_subdev_cleanup(sd); |
| media_entity_cleanup(&sd->entity); |
| v4l2_ctrl_handler_free(<6911uxe->ctrl_handler); |
| pm_runtime_disable(&client->dev); |
| pm_runtime_set_suspended(&client->dev); |
| } |
| |
| static int lt6911uxe_probe(struct i2c_client *client) |
| { |
| struct lt6911uxe *lt6911uxe; |
| struct device *dev = &client->dev; |
| int ret; |
| |
| lt6911uxe = devm_kzalloc(dev, sizeof(*lt6911uxe), GFP_KERNEL); |
| if (!lt6911uxe) |
| return -ENOMEM; |
| |
| lt6911uxe->regmap = devm_regmap_init_i2c(client, |
| <6911uxe_regmap_config); |
| if (IS_ERR(lt6911uxe->regmap)) |
| return dev_err_probe(dev, PTR_ERR(lt6911uxe->regmap), |
| "failed to init CCI\n"); |
| |
| v4l2_i2c_subdev_init(<6911uxe->sd, client, <6911uxe_subdev_ops); |
| |
| lt6911uxe->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_IN); |
| if (IS_ERR(lt6911uxe->reset_gpio)) |
| return dev_err_probe(dev, PTR_ERR(lt6911uxe->reset_gpio), |
| "failed to get reset gpio\n"); |
| |
| lt6911uxe->irq_gpio = devm_gpiod_get(dev, "readystat", GPIOD_IN); |
| if (IS_ERR(lt6911uxe->irq_gpio)) |
| return dev_err_probe(dev, PTR_ERR(lt6911uxe->irq_gpio), |
| "failed to get ready_stat gpio\n"); |
| |
| ret = lt6911uxe_fwnode_parse(lt6911uxe, dev); |
| if (ret) |
| return ret; |
| |
| usleep_range(10000, 10500); |
| |
| ret = lt6911uxe_identify_module(lt6911uxe, dev); |
| if (ret) |
| return dev_err_probe(dev, ret, "failed to find chip\n"); |
| |
| ret = lt6911uxe_init_controls(lt6911uxe); |
| if (ret) |
| return dev_err_probe(dev, ret, "failed to init control\n"); |
| |
| lt6911uxe->sd.dev = dev; |
| lt6911uxe->sd.internal_ops = <6911uxe_internal_ops; |
| lt6911uxe->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; |
| lt6911uxe->sd.entity.ops = <6911uxe_subdev_entity_ops; |
| lt6911uxe->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; |
| lt6911uxe->pad.flags = MEDIA_PAD_FL_SOURCE; |
| ret = media_entity_pads_init(<6911uxe->sd.entity, 1, <6911uxe->pad); |
| if (ret) { |
| dev_err(dev, "failed to init entity pads: %d\n", ret); |
| goto v4l2_ctrl_handler_free; |
| } |
| |
| /* |
| * Device is already turned on by i2c-core with ACPI domain PM. |
| * Enable runtime PM and turn off the device. |
| */ |
| pm_runtime_set_active(dev); |
| pm_runtime_enable(dev); |
| pm_runtime_idle(dev); |
| |
| ret = v4l2_subdev_init_finalize(<6911uxe->sd); |
| if (ret) { |
| dev_err(dev, "failed to init v4l2 subdev: %d\n", ret); |
| goto media_entity_cleanup; |
| } |
| |
| /* Setting irq */ |
| ret = request_threaded_irq(gpiod_to_irq(lt6911uxe->irq_gpio), NULL, |
| lt6911uxe_threaded_irq_fn, |
| IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | |
| IRQF_ONESHOT, NULL, lt6911uxe); |
| if (ret) { |
| dev_err(dev, "failed to request IRQ: %d\n", ret); |
| goto subdev_cleanup; |
| } |
| |
| ret = v4l2_async_register_subdev_sensor(<6911uxe->sd); |
| if (ret) { |
| dev_err(dev, "failed to register V4L2 subdev: %d\n", ret); |
| goto free_irq; |
| } |
| |
| return 0; |
| |
| free_irq: |
| free_irq(gpiod_to_irq(lt6911uxe->irq_gpio), lt6911uxe); |
| |
| subdev_cleanup: |
| v4l2_subdev_cleanup(<6911uxe->sd); |
| |
| media_entity_cleanup: |
| pm_runtime_disable(dev); |
| pm_runtime_set_suspended(dev); |
| media_entity_cleanup(<6911uxe->sd.entity); |
| |
| v4l2_ctrl_handler_free: |
| v4l2_ctrl_handler_free(lt6911uxe->sd.ctrl_handler); |
| |
| return ret; |
| } |
| |
| static const struct acpi_device_id lt6911uxe_acpi_ids[] = { |
| { "INTC10C5" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(acpi, lt6911uxe_acpi_ids); |
| |
| static struct i2c_driver lt6911uxe_i2c_driver = { |
| .driver = { |
| .name = "lt6911uxe", |
| .acpi_match_table = ACPI_PTR(lt6911uxe_acpi_ids), |
| }, |
| .probe = lt6911uxe_probe, |
| .remove = lt6911uxe_remove, |
| }; |
| |
| module_i2c_driver(lt6911uxe_i2c_driver); |
| |
| MODULE_AUTHOR("Yan Dongcheng <dongcheng.yan@intel.com>"); |
| MODULE_DESCRIPTION("Lontium lt6911uxe HDMI to MIPI Bridge Driver"); |
| MODULE_LICENSE("GPL"); |