| // SPDX-License-Identifier: GPL-2.0-only | 
 | /* | 
 |  * lp5523.c - LP5523, LP55231 LED Driver | 
 |  * | 
 |  * Copyright (C) 2010 Nokia Corporation | 
 |  * Copyright (C) 2012 Texas Instruments | 
 |  * | 
 |  * Contact: Samu Onkalo <samu.p.onkalo@nokia.com> | 
 |  *          Milo(Woogyom) Kim <milo.kim@ti.com> | 
 |  */ | 
 |  | 
 | #include <linux/delay.h> | 
 | #include <linux/firmware.h> | 
 | #include <linux/i2c.h> | 
 | #include <linux/leds.h> | 
 | #include <linux/module.h> | 
 | #include <linux/mutex.h> | 
 | #include <linux/of.h> | 
 | #include <linux/platform_data/leds-lp55xx.h> | 
 | #include <linux/slab.h> | 
 |  | 
 | #include "leds-lp55xx-common.h" | 
 |  | 
 | #define LP5523_PROGRAM_LENGTH		32	/* bytes */ | 
 | /* Memory is used like this: | 
 |    0x00 engine 1 program | 
 |    0x10 engine 2 program | 
 |    0x20 engine 3 program | 
 |    0x30 engine 1 muxing info | 
 |    0x40 engine 2 muxing info | 
 |    0x50 engine 3 muxing info | 
 | */ | 
 | #define LP5523_MAX_LEDS			9 | 
 |  | 
 | /* Registers */ | 
 | #define LP5523_REG_ENABLE		0x00 | 
 | #define LP5523_REG_OP_MODE		0x01 | 
 | #define LP5523_REG_ENABLE_LEDS_MSB	0x04 | 
 | #define LP5523_REG_ENABLE_LEDS_LSB	0x05 | 
 | #define LP5523_REG_LED_CTRL_BASE	0x06 | 
 | #define LP5523_REG_LED_PWM_BASE		0x16 | 
 | #define LP5523_REG_LED_CURRENT_BASE	0x26 | 
 | #define LP5523_REG_CONFIG		0x36 | 
 | #define LP5523_REG_STATUS		0x3A | 
 | #define LP5523_REG_RESET		0x3D | 
 | #define LP5523_REG_LED_TEST_CTRL	0x41 | 
 | #define LP5523_REG_LED_TEST_ADC		0x42 | 
 | #define LP5523_REG_MASTER_FADER_BASE	0x48 | 
 | #define LP5523_REG_CH1_PROG_START	0x4C | 
 | #define LP5523_REG_CH2_PROG_START	0x4D | 
 | #define LP5523_REG_CH3_PROG_START	0x4E | 
 | #define LP5523_REG_PROG_PAGE_SEL	0x4F | 
 | #define LP5523_REG_PROG_MEM		0x50 | 
 |  | 
 | /* Bit description in registers */ | 
 | #define LP5523_ENABLE			0x40 | 
 | #define LP5523_AUTO_INC			0x40 | 
 | #define LP5523_PWR_SAVE			0x20 | 
 | #define LP5523_PWM_PWR_SAVE		0x04 | 
 | #define LP5523_CP_AUTO			0x18 | 
 | #define LP5523_AUTO_CLK			0x02 | 
 |  | 
 | #define LP5523_EN_LEDTEST		0x80 | 
 | #define LP5523_LEDTEST_DONE		0x80 | 
 | #define LP5523_RESET			0xFF | 
 | #define LP5523_ADC_SHORTCIRC_LIM	80 | 
 | #define LP5523_EXT_CLK_USED		0x08 | 
 | #define LP5523_ENG_STATUS_MASK		0x07 | 
 |  | 
 | #define LP5523_FADER_MAPPING_MASK	0xC0 | 
 | #define LP5523_FADER_MAPPING_SHIFT	6 | 
 |  | 
 | /* Memory Page Selection */ | 
 | #define LP5523_PAGE_ENG1		0 | 
 | #define LP5523_PAGE_ENG2		1 | 
 | #define LP5523_PAGE_ENG3		2 | 
 | #define LP5523_PAGE_MUX1		3 | 
 | #define LP5523_PAGE_MUX2		4 | 
 | #define LP5523_PAGE_MUX3		5 | 
 |  | 
 | /* Program Memory Operations */ | 
 | #define LP5523_MODE_ENG1_M		0x30	/* Operation Mode Register */ | 
 | #define LP5523_MODE_ENG2_M		0x0C | 
 | #define LP5523_MODE_ENG3_M		0x03 | 
 | #define LP5523_LOAD_ENG1		0x10 | 
 | #define LP5523_LOAD_ENG2		0x04 | 
 | #define LP5523_LOAD_ENG3		0x01 | 
 |  | 
 | #define LP5523_ENG1_IS_LOADING(mode)	\ | 
 | 	((mode & LP5523_MODE_ENG1_M) == LP5523_LOAD_ENG1) | 
 | #define LP5523_ENG2_IS_LOADING(mode)	\ | 
 | 	((mode & LP5523_MODE_ENG2_M) == LP5523_LOAD_ENG2) | 
 | #define LP5523_ENG3_IS_LOADING(mode)	\ | 
 | 	((mode & LP5523_MODE_ENG3_M) == LP5523_LOAD_ENG3) | 
 |  | 
 | #define LP5523_EXEC_ENG1_M		0x30	/* Enable Register */ | 
 | #define LP5523_EXEC_ENG2_M		0x0C | 
 | #define LP5523_EXEC_ENG3_M		0x03 | 
 | #define LP5523_EXEC_M			0x3F | 
 | #define LP5523_RUN_ENG1			0x20 | 
 | #define LP5523_RUN_ENG2			0x08 | 
 | #define LP5523_RUN_ENG3			0x02 | 
 |  | 
 | #define LED_ACTIVE(mux, led)		(!!(mux & (0x0001 << led))) | 
 |  | 
 | enum lp5523_chip_id { | 
 | 	LP5523, | 
 | 	LP55231, | 
 | }; | 
 |  | 
 | static int lp5523_init_program_engine(struct lp55xx_chip *chip); | 
 |  | 
 | static inline void lp5523_wait_opmode_done(void) | 
 | { | 
 | 	usleep_range(1000, 2000); | 
 | } | 
 |  | 
 | static void lp5523_set_led_current(struct lp55xx_led *led, u8 led_current) | 
 | { | 
 | 	led->led_current = led_current; | 
 | 	lp55xx_write(led->chip, LP5523_REG_LED_CURRENT_BASE + led->chan_nr, | 
 | 		led_current); | 
 | } | 
 |  | 
 | static int lp5523_post_init_device(struct lp55xx_chip *chip) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_ENABLE, LP5523_ENABLE); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	/* Chip startup time is 500 us, 1 - 2 ms gives some margin */ | 
 | 	usleep_range(1000, 2000); | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_CONFIG, | 
 | 			    LP5523_AUTO_INC | LP5523_PWR_SAVE | | 
 | 			    LP5523_CP_AUTO | LP5523_AUTO_CLK | | 
 | 			    LP5523_PWM_PWR_SAVE); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	/* turn on all leds */ | 
 | 	ret = lp55xx_write(chip, LP5523_REG_ENABLE_LEDS_MSB, 0x01); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_ENABLE_LEDS_LSB, 0xff); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	return lp5523_init_program_engine(chip); | 
 | } | 
 |  | 
 | static void lp5523_load_engine(struct lp55xx_chip *chip) | 
 | { | 
 | 	enum lp55xx_engine_index idx = chip->engine_idx; | 
 | 	static const u8 mask[] = { | 
 | 		[LP55XX_ENGINE_1] = LP5523_MODE_ENG1_M, | 
 | 		[LP55XX_ENGINE_2] = LP5523_MODE_ENG2_M, | 
 | 		[LP55XX_ENGINE_3] = LP5523_MODE_ENG3_M, | 
 | 	}; | 
 |  | 
 | 	static const u8 val[] = { | 
 | 		[LP55XX_ENGINE_1] = LP5523_LOAD_ENG1, | 
 | 		[LP55XX_ENGINE_2] = LP5523_LOAD_ENG2, | 
 | 		[LP55XX_ENGINE_3] = LP5523_LOAD_ENG3, | 
 | 	}; | 
 |  | 
 | 	lp55xx_update_bits(chip, LP5523_REG_OP_MODE, mask[idx], val[idx]); | 
 |  | 
 | 	lp5523_wait_opmode_done(); | 
 | } | 
 |  | 
 | static void lp5523_load_engine_and_select_page(struct lp55xx_chip *chip) | 
 | { | 
 | 	enum lp55xx_engine_index idx = chip->engine_idx; | 
 | 	static const u8 page_sel[] = { | 
 | 		[LP55XX_ENGINE_1] = LP5523_PAGE_ENG1, | 
 | 		[LP55XX_ENGINE_2] = LP5523_PAGE_ENG2, | 
 | 		[LP55XX_ENGINE_3] = LP5523_PAGE_ENG3, | 
 | 	}; | 
 |  | 
 | 	lp5523_load_engine(chip); | 
 |  | 
 | 	lp55xx_write(chip, LP5523_REG_PROG_PAGE_SEL, page_sel[idx]); | 
 | } | 
 |  | 
 | static void lp5523_stop_all_engines(struct lp55xx_chip *chip) | 
 | { | 
 | 	lp55xx_write(chip, LP5523_REG_OP_MODE, 0); | 
 | 	lp5523_wait_opmode_done(); | 
 | } | 
 |  | 
 | static void lp5523_stop_engine(struct lp55xx_chip *chip) | 
 | { | 
 | 	enum lp55xx_engine_index idx = chip->engine_idx; | 
 | 	static const u8 mask[] = { | 
 | 		[LP55XX_ENGINE_1] = LP5523_MODE_ENG1_M, | 
 | 		[LP55XX_ENGINE_2] = LP5523_MODE_ENG2_M, | 
 | 		[LP55XX_ENGINE_3] = LP5523_MODE_ENG3_M, | 
 | 	}; | 
 |  | 
 | 	lp55xx_update_bits(chip, LP5523_REG_OP_MODE, mask[idx], 0); | 
 |  | 
 | 	lp5523_wait_opmode_done(); | 
 | } | 
 |  | 
 | static void lp5523_turn_off_channels(struct lp55xx_chip *chip) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	for (i = 0; i < LP5523_MAX_LEDS; i++) | 
 | 		lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + i, 0); | 
 | } | 
 |  | 
 | static void lp5523_run_engine(struct lp55xx_chip *chip, bool start) | 
 | { | 
 | 	int ret; | 
 | 	u8 mode; | 
 | 	u8 exec; | 
 |  | 
 | 	/* stop engine */ | 
 | 	if (!start) { | 
 | 		lp5523_stop_engine(chip); | 
 | 		lp5523_turn_off_channels(chip); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * To run the engine, | 
 | 	 * operation mode and enable register should updated at the same time | 
 | 	 */ | 
 |  | 
 | 	ret = lp55xx_read(chip, LP5523_REG_OP_MODE, &mode); | 
 | 	if (ret) | 
 | 		return; | 
 |  | 
 | 	ret = lp55xx_read(chip, LP5523_REG_ENABLE, &exec); | 
 | 	if (ret) | 
 | 		return; | 
 |  | 
 | 	/* change operation mode to RUN only when each engine is loading */ | 
 | 	if (LP5523_ENG1_IS_LOADING(mode)) { | 
 | 		mode = (mode & ~LP5523_MODE_ENG1_M) | LP5523_RUN_ENG1; | 
 | 		exec = (exec & ~LP5523_EXEC_ENG1_M) | LP5523_RUN_ENG1; | 
 | 	} | 
 |  | 
 | 	if (LP5523_ENG2_IS_LOADING(mode)) { | 
 | 		mode = (mode & ~LP5523_MODE_ENG2_M) | LP5523_RUN_ENG2; | 
 | 		exec = (exec & ~LP5523_EXEC_ENG2_M) | LP5523_RUN_ENG2; | 
 | 	} | 
 |  | 
 | 	if (LP5523_ENG3_IS_LOADING(mode)) { | 
 | 		mode = (mode & ~LP5523_MODE_ENG3_M) | LP5523_RUN_ENG3; | 
 | 		exec = (exec & ~LP5523_EXEC_ENG3_M) | LP5523_RUN_ENG3; | 
 | 	} | 
 |  | 
 | 	lp55xx_write(chip, LP5523_REG_OP_MODE, mode); | 
 | 	lp5523_wait_opmode_done(); | 
 |  | 
 | 	lp55xx_update_bits(chip, LP5523_REG_ENABLE, LP5523_EXEC_M, exec); | 
 | } | 
 |  | 
 | static int lp5523_init_program_engine(struct lp55xx_chip *chip) | 
 | { | 
 | 	int i; | 
 | 	int j; | 
 | 	int ret; | 
 | 	u8 status; | 
 | 	/* one pattern per engine setting LED MUX start and stop addresses */ | 
 | 	static const u8 pattern[][LP5523_PROGRAM_LENGTH] =  { | 
 | 		{ 0x9c, 0x30, 0x9c, 0xb0, 0x9d, 0x80, 0xd8, 0x00, 0}, | 
 | 		{ 0x9c, 0x40, 0x9c, 0xc0, 0x9d, 0x80, 0xd8, 0x00, 0}, | 
 | 		{ 0x9c, 0x50, 0x9c, 0xd0, 0x9d, 0x80, 0xd8, 0x00, 0}, | 
 | 	}; | 
 |  | 
 | 	/* hardcode 32 bytes of memory for each engine from program memory */ | 
 | 	ret = lp55xx_write(chip, LP5523_REG_CH1_PROG_START, 0x00); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_CH2_PROG_START, 0x10); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_CH3_PROG_START, 0x20); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	/* write LED MUX address space for each engine */ | 
 | 	for (i = LP55XX_ENGINE_1; i <= LP55XX_ENGINE_3; i++) { | 
 | 		chip->engine_idx = i; | 
 | 		lp5523_load_engine_and_select_page(chip); | 
 |  | 
 | 		for (j = 0; j < LP5523_PROGRAM_LENGTH; j++) { | 
 | 			ret = lp55xx_write(chip, LP5523_REG_PROG_MEM + j, | 
 | 					pattern[i - 1][j]); | 
 | 			if (ret) | 
 | 				goto out; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	lp5523_run_engine(chip, true); | 
 |  | 
 | 	/* Let the programs run for couple of ms and check the engine status */ | 
 | 	usleep_range(3000, 6000); | 
 | 	ret = lp55xx_read(chip, LP5523_REG_STATUS, &status); | 
 | 	if (ret) | 
 | 		return ret; | 
 | 	status &= LP5523_ENG_STATUS_MASK; | 
 |  | 
 | 	if (status != LP5523_ENG_STATUS_MASK) { | 
 | 		dev_err(&chip->cl->dev, | 
 | 			"could not configure LED engine, status = 0x%.2x\n", | 
 | 			status); | 
 | 		ret = -1; | 
 | 	} | 
 |  | 
 | out: | 
 | 	lp5523_stop_all_engines(chip); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int lp5523_update_program_memory(struct lp55xx_chip *chip, | 
 | 					const u8 *data, size_t size) | 
 | { | 
 | 	u8 pattern[LP5523_PROGRAM_LENGTH] = {0}; | 
 | 	unsigned cmd; | 
 | 	char c[3]; | 
 | 	int nrchars; | 
 | 	int ret; | 
 | 	int offset = 0; | 
 | 	int i = 0; | 
 |  | 
 | 	while ((offset < size - 1) && (i < LP5523_PROGRAM_LENGTH)) { | 
 | 		/* separate sscanfs because length is working only for %s */ | 
 | 		ret = sscanf(data + offset, "%2s%n ", c, &nrchars); | 
 | 		if (ret != 1) | 
 | 			goto err; | 
 |  | 
 | 		ret = sscanf(c, "%2x", &cmd); | 
 | 		if (ret != 1) | 
 | 			goto err; | 
 |  | 
 | 		pattern[i] = (u8)cmd; | 
 | 		offset += nrchars; | 
 | 		i++; | 
 | 	} | 
 |  | 
 | 	/* Each instruction is 16bit long. Check that length is even */ | 
 | 	if (i % 2) | 
 | 		goto err; | 
 |  | 
 | 	for (i = 0; i < LP5523_PROGRAM_LENGTH; i++) { | 
 | 		ret = lp55xx_write(chip, LP5523_REG_PROG_MEM + i, pattern[i]); | 
 | 		if (ret) | 
 | 			return -EINVAL; | 
 | 	} | 
 |  | 
 | 	return size; | 
 |  | 
 | err: | 
 | 	dev_err(&chip->cl->dev, "wrong pattern format\n"); | 
 | 	return -EINVAL; | 
 | } | 
 |  | 
 | static void lp5523_firmware_loaded(struct lp55xx_chip *chip) | 
 | { | 
 | 	const struct firmware *fw = chip->fw; | 
 |  | 
 | 	if (fw->size > LP5523_PROGRAM_LENGTH) { | 
 | 		dev_err(&chip->cl->dev, "firmware data size overflow: %zu\n", | 
 | 			fw->size); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Program memory sequence | 
 | 	 *  1) set engine mode to "LOAD" | 
 | 	 *  2) write firmware data into program memory | 
 | 	 */ | 
 |  | 
 | 	lp5523_load_engine_and_select_page(chip); | 
 | 	lp5523_update_program_memory(chip, fw->data, fw->size); | 
 | } | 
 |  | 
 | static ssize_t show_engine_mode(struct device *dev, | 
 | 				struct device_attribute *attr, | 
 | 				char *buf, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	enum lp55xx_engine_mode mode = chip->engines[nr - 1].mode; | 
 |  | 
 | 	switch (mode) { | 
 | 	case LP55XX_ENGINE_RUN: | 
 | 		return sprintf(buf, "run\n"); | 
 | 	case LP55XX_ENGINE_LOAD: | 
 | 		return sprintf(buf, "load\n"); | 
 | 	case LP55XX_ENGINE_DISABLED: | 
 | 	default: | 
 | 		return sprintf(buf, "disabled\n"); | 
 | 	} | 
 | } | 
 | show_mode(1) | 
 | show_mode(2) | 
 | show_mode(3) | 
 |  | 
 | static ssize_t store_engine_mode(struct device *dev, | 
 | 				 struct device_attribute *attr, | 
 | 				 const char *buf, size_t len, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	struct lp55xx_engine *engine = &chip->engines[nr - 1]; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	chip->engine_idx = nr; | 
 |  | 
 | 	if (!strncmp(buf, "run", 3)) { | 
 | 		lp5523_run_engine(chip, true); | 
 | 		engine->mode = LP55XX_ENGINE_RUN; | 
 | 	} else if (!strncmp(buf, "load", 4)) { | 
 | 		lp5523_stop_engine(chip); | 
 | 		lp5523_load_engine(chip); | 
 | 		engine->mode = LP55XX_ENGINE_LOAD; | 
 | 	} else if (!strncmp(buf, "disabled", 8)) { | 
 | 		lp5523_stop_engine(chip); | 
 | 		engine->mode = LP55XX_ENGINE_DISABLED; | 
 | 	} | 
 |  | 
 | 	mutex_unlock(&chip->lock); | 
 |  | 
 | 	return len; | 
 | } | 
 | store_mode(1) | 
 | store_mode(2) | 
 | store_mode(3) | 
 |  | 
 | static int lp5523_mux_parse(const char *buf, u16 *mux, size_t len) | 
 | { | 
 | 	u16 tmp_mux = 0; | 
 | 	int i; | 
 |  | 
 | 	len = min_t(int, len, LP5523_MAX_LEDS); | 
 |  | 
 | 	for (i = 0; i < len; i++) { | 
 | 		switch (buf[i]) { | 
 | 		case '1': | 
 | 			tmp_mux |= (1 << i); | 
 | 			break; | 
 | 		case '0': | 
 | 			break; | 
 | 		case '\n': | 
 | 			i = len; | 
 | 			break; | 
 | 		default: | 
 | 			return -1; | 
 | 		} | 
 | 	} | 
 | 	*mux = tmp_mux; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void lp5523_mux_to_array(u16 led_mux, char *array) | 
 | { | 
 | 	int i, pos = 0; | 
 | 	for (i = 0; i < LP5523_MAX_LEDS; i++) | 
 | 		pos += sprintf(array + pos, "%x", LED_ACTIVE(led_mux, i)); | 
 |  | 
 | 	array[pos] = '\0'; | 
 | } | 
 |  | 
 | static ssize_t show_engine_leds(struct device *dev, | 
 | 			    struct device_attribute *attr, | 
 | 			    char *buf, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	char mux[LP5523_MAX_LEDS + 1]; | 
 |  | 
 | 	lp5523_mux_to_array(chip->engines[nr - 1].led_mux, mux); | 
 |  | 
 | 	return sprintf(buf, "%s\n", mux); | 
 | } | 
 | show_leds(1) | 
 | show_leds(2) | 
 | show_leds(3) | 
 |  | 
 | static int lp5523_load_mux(struct lp55xx_chip *chip, u16 mux, int nr) | 
 | { | 
 | 	struct lp55xx_engine *engine = &chip->engines[nr - 1]; | 
 | 	int ret; | 
 | 	static const u8 mux_page[] = { | 
 | 		[LP55XX_ENGINE_1] = LP5523_PAGE_MUX1, | 
 | 		[LP55XX_ENGINE_2] = LP5523_PAGE_MUX2, | 
 | 		[LP55XX_ENGINE_3] = LP5523_PAGE_MUX3, | 
 | 	}; | 
 |  | 
 | 	lp5523_load_engine(chip); | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_PROG_PAGE_SEL, mux_page[nr]); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_PROG_MEM , (u8)(mux >> 8)); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	ret = lp55xx_write(chip, LP5523_REG_PROG_MEM + 1, (u8)(mux)); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	engine->led_mux = mux; | 
 | 	return 0; | 
 | } | 
 |  | 
 | static ssize_t store_engine_leds(struct device *dev, | 
 | 			     struct device_attribute *attr, | 
 | 			     const char *buf, size_t len, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	struct lp55xx_engine *engine = &chip->engines[nr - 1]; | 
 | 	u16 mux = 0; | 
 | 	ssize_t ret; | 
 |  | 
 | 	if (lp5523_mux_parse(buf, &mux, len)) | 
 | 		return -EINVAL; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	chip->engine_idx = nr; | 
 | 	ret = -EINVAL; | 
 |  | 
 | 	if (engine->mode != LP55XX_ENGINE_LOAD) | 
 | 		goto leave; | 
 |  | 
 | 	if (lp5523_load_mux(chip, mux, nr)) | 
 | 		goto leave; | 
 |  | 
 | 	ret = len; | 
 | leave: | 
 | 	mutex_unlock(&chip->lock); | 
 | 	return ret; | 
 | } | 
 | store_leds(1) | 
 | store_leds(2) | 
 | store_leds(3) | 
 |  | 
 | static ssize_t store_engine_load(struct device *dev, | 
 | 			     struct device_attribute *attr, | 
 | 			     const char *buf, size_t len, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int ret; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	chip->engine_idx = nr; | 
 | 	lp5523_load_engine_and_select_page(chip); | 
 | 	ret = lp5523_update_program_memory(chip, buf, len); | 
 |  | 
 | 	mutex_unlock(&chip->lock); | 
 |  | 
 | 	return ret; | 
 | } | 
 | store_load(1) | 
 | store_load(2) | 
 | store_load(3) | 
 |  | 
 | static ssize_t lp5523_selftest(struct device *dev, | 
 | 			       struct device_attribute *attr, | 
 | 			       char *buf) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	struct lp55xx_platform_data *pdata = chip->pdata; | 
 | 	int i, ret, pos = 0; | 
 | 	u8 status, adc, vdd; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	ret = lp55xx_read(chip, LP5523_REG_STATUS, &status); | 
 | 	if (ret < 0) | 
 | 		goto fail; | 
 |  | 
 | 	/* Check that ext clock is really in use if requested */ | 
 | 	if (pdata->clock_mode == LP55XX_CLOCK_EXT) { | 
 | 		if  ((status & LP5523_EXT_CLK_USED) == 0) | 
 | 			goto fail; | 
 | 	} | 
 |  | 
 | 	/* Measure VDD (i.e. VBAT) first (channel 16 corresponds to VDD) */ | 
 | 	lp55xx_write(chip, LP5523_REG_LED_TEST_CTRL, LP5523_EN_LEDTEST | 16); | 
 | 	usleep_range(3000, 6000); /* ADC conversion time is typically 2.7 ms */ | 
 | 	ret = lp55xx_read(chip, LP5523_REG_STATUS, &status); | 
 | 	if (ret < 0) | 
 | 		goto fail; | 
 |  | 
 | 	if (!(status & LP5523_LEDTEST_DONE)) | 
 | 		usleep_range(3000, 6000); /* Was not ready. Wait little bit */ | 
 |  | 
 | 	ret = lp55xx_read(chip, LP5523_REG_LED_TEST_ADC, &vdd); | 
 | 	if (ret < 0) | 
 | 		goto fail; | 
 |  | 
 | 	vdd--;	/* There may be some fluctuation in measurement */ | 
 |  | 
 | 	for (i = 0; i < LP5523_MAX_LEDS; i++) { | 
 | 		/* Skip non-existing channels */ | 
 | 		if (pdata->led_config[i].led_current == 0) | 
 | 			continue; | 
 |  | 
 | 		/* Set default current */ | 
 | 		lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + i, | 
 | 			pdata->led_config[i].led_current); | 
 |  | 
 | 		lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + i, 0xff); | 
 | 		/* let current stabilize 2 - 4ms before measurements start */ | 
 | 		usleep_range(2000, 4000); | 
 | 		lp55xx_write(chip, LP5523_REG_LED_TEST_CTRL, | 
 | 			     LP5523_EN_LEDTEST | i); | 
 | 		/* ADC conversion time is 2.7 ms typically */ | 
 | 		usleep_range(3000, 6000); | 
 | 		ret = lp55xx_read(chip, LP5523_REG_STATUS, &status); | 
 | 		if (ret < 0) | 
 | 			goto fail; | 
 |  | 
 | 		if (!(status & LP5523_LEDTEST_DONE)) | 
 | 			usleep_range(3000, 6000);/* Was not ready. Wait. */ | 
 |  | 
 | 		ret = lp55xx_read(chip, LP5523_REG_LED_TEST_ADC, &adc); | 
 | 		if (ret < 0) | 
 | 			goto fail; | 
 |  | 
 | 		if (adc >= vdd || adc < LP5523_ADC_SHORTCIRC_LIM) | 
 | 			pos += sprintf(buf + pos, "LED %d FAIL\n", i); | 
 |  | 
 | 		lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + i, 0x00); | 
 |  | 
 | 		/* Restore current */ | 
 | 		lp55xx_write(chip, LP5523_REG_LED_CURRENT_BASE + i, | 
 | 			led->led_current); | 
 | 		led++; | 
 | 	} | 
 | 	if (pos == 0) | 
 | 		pos = sprintf(buf, "OK\n"); | 
 | 	goto release_lock; | 
 | fail: | 
 | 	pos = sprintf(buf, "FAIL\n"); | 
 |  | 
 | release_lock: | 
 | 	mutex_unlock(&chip->lock); | 
 |  | 
 | 	return pos; | 
 | } | 
 |  | 
 | #define show_fader(nr)						\ | 
 | static ssize_t show_master_fader##nr(struct device *dev,	\ | 
 | 			    struct device_attribute *attr,	\ | 
 | 			    char *buf)				\ | 
 | {								\ | 
 | 	return show_master_fader(dev, attr, buf, nr);		\ | 
 | } | 
 |  | 
 | #define store_fader(nr)						\ | 
 | static ssize_t store_master_fader##nr(struct device *dev,	\ | 
 | 			     struct device_attribute *attr,	\ | 
 | 			     const char *buf, size_t len)	\ | 
 | {								\ | 
 | 	return store_master_fader(dev, attr, buf, len, nr);	\ | 
 | } | 
 |  | 
 | static ssize_t show_master_fader(struct device *dev, | 
 | 				 struct device_attribute *attr, | 
 | 				 char *buf, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int ret; | 
 | 	u8 val; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 | 	ret = lp55xx_read(chip, LP5523_REG_MASTER_FADER_BASE + nr - 1, &val); | 
 | 	mutex_unlock(&chip->lock); | 
 |  | 
 | 	if (ret == 0) | 
 | 		ret = sprintf(buf, "%u\n", val); | 
 |  | 
 | 	return ret; | 
 | } | 
 | show_fader(1) | 
 | show_fader(2) | 
 | show_fader(3) | 
 |  | 
 | static ssize_t store_master_fader(struct device *dev, | 
 | 				  struct device_attribute *attr, | 
 | 				  const char *buf, size_t len, int nr) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int ret; | 
 | 	unsigned long val; | 
 |  | 
 | 	if (kstrtoul(buf, 0, &val)) | 
 | 		return -EINVAL; | 
 |  | 
 | 	if (val > 0xff) | 
 | 		return -EINVAL; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 | 	ret = lp55xx_write(chip, LP5523_REG_MASTER_FADER_BASE + nr - 1, | 
 | 			   (u8)val); | 
 | 	mutex_unlock(&chip->lock); | 
 |  | 
 | 	if (ret == 0) | 
 | 		ret = len; | 
 |  | 
 | 	return ret; | 
 | } | 
 | store_fader(1) | 
 | store_fader(2) | 
 | store_fader(3) | 
 |  | 
 | static ssize_t show_master_fader_leds(struct device *dev, | 
 | 				      struct device_attribute *attr, | 
 | 				      char *buf) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int i, ret, pos = 0; | 
 | 	u8 val; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	for (i = 0; i < LP5523_MAX_LEDS; i++) { | 
 | 		ret = lp55xx_read(chip, LP5523_REG_LED_CTRL_BASE + i, &val); | 
 | 		if (ret) | 
 | 			goto leave; | 
 |  | 
 | 		val = (val & LP5523_FADER_MAPPING_MASK) | 
 | 			>> LP5523_FADER_MAPPING_SHIFT; | 
 | 		if (val > 3) { | 
 | 			ret = -EINVAL; | 
 | 			goto leave; | 
 | 		} | 
 | 		buf[pos++] = val + '0'; | 
 | 	} | 
 | 	buf[pos++] = '\n'; | 
 | 	ret = pos; | 
 | leave: | 
 | 	mutex_unlock(&chip->lock); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static ssize_t store_master_fader_leds(struct device *dev, | 
 | 				       struct device_attribute *attr, | 
 | 				       const char *buf, size_t len) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int i, n, ret; | 
 | 	u8 val; | 
 |  | 
 | 	n = min_t(int, len, LP5523_MAX_LEDS); | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 |  | 
 | 	for (i = 0; i < n; i++) { | 
 | 		if (buf[i] >= '0' && buf[i] <= '3') { | 
 | 			val = (buf[i] - '0') << LP5523_FADER_MAPPING_SHIFT; | 
 | 			ret = lp55xx_update_bits(chip, | 
 | 						 LP5523_REG_LED_CTRL_BASE + i, | 
 | 						 LP5523_FADER_MAPPING_MASK, | 
 | 						 val); | 
 | 			if (ret) | 
 | 				goto leave; | 
 | 		} else { | 
 | 			ret = -EINVAL; | 
 | 			goto leave; | 
 | 		} | 
 | 	} | 
 | 	ret = len; | 
 | leave: | 
 | 	mutex_unlock(&chip->lock); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int lp5523_led_brightness(struct lp55xx_led *led) | 
 | { | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 | 	int ret; | 
 |  | 
 | 	mutex_lock(&chip->lock); | 
 | 	ret = lp55xx_write(chip, LP5523_REG_LED_PWM_BASE + led->chan_nr, | 
 | 		     led->brightness); | 
 | 	mutex_unlock(&chip->lock); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static LP55XX_DEV_ATTR_RW(engine1_mode, show_engine1_mode, store_engine1_mode); | 
 | static LP55XX_DEV_ATTR_RW(engine2_mode, show_engine2_mode, store_engine2_mode); | 
 | static LP55XX_DEV_ATTR_RW(engine3_mode, show_engine3_mode, store_engine3_mode); | 
 | static LP55XX_DEV_ATTR_RW(engine1_leds, show_engine1_leds, store_engine1_leds); | 
 | static LP55XX_DEV_ATTR_RW(engine2_leds, show_engine2_leds, store_engine2_leds); | 
 | static LP55XX_DEV_ATTR_RW(engine3_leds, show_engine3_leds, store_engine3_leds); | 
 | static LP55XX_DEV_ATTR_WO(engine1_load, store_engine1_load); | 
 | static LP55XX_DEV_ATTR_WO(engine2_load, store_engine2_load); | 
 | static LP55XX_DEV_ATTR_WO(engine3_load, store_engine3_load); | 
 | static LP55XX_DEV_ATTR_RO(selftest, lp5523_selftest); | 
 | static LP55XX_DEV_ATTR_RW(master_fader1, show_master_fader1, | 
 | 			  store_master_fader1); | 
 | static LP55XX_DEV_ATTR_RW(master_fader2, show_master_fader2, | 
 | 			  store_master_fader2); | 
 | static LP55XX_DEV_ATTR_RW(master_fader3, show_master_fader3, | 
 | 			  store_master_fader3); | 
 | static LP55XX_DEV_ATTR_RW(master_fader_leds, show_master_fader_leds, | 
 | 			  store_master_fader_leds); | 
 |  | 
 | static struct attribute *lp5523_attributes[] = { | 
 | 	&dev_attr_engine1_mode.attr, | 
 | 	&dev_attr_engine2_mode.attr, | 
 | 	&dev_attr_engine3_mode.attr, | 
 | 	&dev_attr_engine1_load.attr, | 
 | 	&dev_attr_engine2_load.attr, | 
 | 	&dev_attr_engine3_load.attr, | 
 | 	&dev_attr_engine1_leds.attr, | 
 | 	&dev_attr_engine2_leds.attr, | 
 | 	&dev_attr_engine3_leds.attr, | 
 | 	&dev_attr_selftest.attr, | 
 | 	&dev_attr_master_fader1.attr, | 
 | 	&dev_attr_master_fader2.attr, | 
 | 	&dev_attr_master_fader3.attr, | 
 | 	&dev_attr_master_fader_leds.attr, | 
 | 	NULL, | 
 | }; | 
 |  | 
 | static const struct attribute_group lp5523_group = { | 
 | 	.attrs = lp5523_attributes, | 
 | }; | 
 |  | 
 | /* Chip specific configurations */ | 
 | static struct lp55xx_device_config lp5523_cfg = { | 
 | 	.reset = { | 
 | 		.addr = LP5523_REG_RESET, | 
 | 		.val  = LP5523_RESET, | 
 | 	}, | 
 | 	.enable = { | 
 | 		.addr = LP5523_REG_ENABLE, | 
 | 		.val  = LP5523_ENABLE, | 
 | 	}, | 
 | 	.max_channel  = LP5523_MAX_LEDS, | 
 | 	.post_init_device   = lp5523_post_init_device, | 
 | 	.brightness_fn      = lp5523_led_brightness, | 
 | 	.set_led_current    = lp5523_set_led_current, | 
 | 	.firmware_cb        = lp5523_firmware_loaded, | 
 | 	.run_engine         = lp5523_run_engine, | 
 | 	.dev_attr_group     = &lp5523_group, | 
 | }; | 
 |  | 
 | static int lp5523_probe(struct i2c_client *client, | 
 | 			const struct i2c_device_id *id) | 
 | { | 
 | 	int ret; | 
 | 	struct lp55xx_chip *chip; | 
 | 	struct lp55xx_led *led; | 
 | 	struct lp55xx_platform_data *pdata = dev_get_platdata(&client->dev); | 
 | 	struct device_node *np = client->dev.of_node; | 
 |  | 
 | 	if (!pdata) { | 
 | 		if (np) { | 
 | 			pdata = lp55xx_of_populate_pdata(&client->dev, np); | 
 | 			if (IS_ERR(pdata)) | 
 | 				return PTR_ERR(pdata); | 
 | 		} else { | 
 | 			dev_err(&client->dev, "no platform data\n"); | 
 | 			return -EINVAL; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL); | 
 | 	if (!chip) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	led = devm_kcalloc(&client->dev, | 
 | 			pdata->num_channels, sizeof(*led), GFP_KERNEL); | 
 | 	if (!led) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	chip->cl = client; | 
 | 	chip->pdata = pdata; | 
 | 	chip->cfg = &lp5523_cfg; | 
 |  | 
 | 	mutex_init(&chip->lock); | 
 |  | 
 | 	i2c_set_clientdata(client, led); | 
 |  | 
 | 	ret = lp55xx_init_device(chip); | 
 | 	if (ret) | 
 | 		goto err_init; | 
 |  | 
 | 	dev_info(&client->dev, "%s Programmable led chip found\n", id->name); | 
 |  | 
 | 	ret = lp55xx_register_leds(led, chip); | 
 | 	if (ret) | 
 | 		goto err_register_leds; | 
 |  | 
 | 	ret = lp55xx_register_sysfs(chip); | 
 | 	if (ret) { | 
 | 		dev_err(&client->dev, "registering sysfs failed\n"); | 
 | 		goto err_register_sysfs; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 |  | 
 | err_register_sysfs: | 
 | 	lp55xx_unregister_leds(led, chip); | 
 | err_register_leds: | 
 | 	lp55xx_deinit_device(chip); | 
 | err_init: | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int lp5523_remove(struct i2c_client *client) | 
 | { | 
 | 	struct lp55xx_led *led = i2c_get_clientdata(client); | 
 | 	struct lp55xx_chip *chip = led->chip; | 
 |  | 
 | 	lp5523_stop_all_engines(chip); | 
 | 	lp55xx_unregister_sysfs(chip); | 
 | 	lp55xx_unregister_leds(led, chip); | 
 | 	lp55xx_deinit_device(chip); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct i2c_device_id lp5523_id[] = { | 
 | 	{ "lp5523",  LP5523 }, | 
 | 	{ "lp55231", LP55231 }, | 
 | 	{ } | 
 | }; | 
 |  | 
 | MODULE_DEVICE_TABLE(i2c, lp5523_id); | 
 |  | 
 | #ifdef CONFIG_OF | 
 | static const struct of_device_id of_lp5523_leds_match[] = { | 
 | 	{ .compatible = "national,lp5523", }, | 
 | 	{ .compatible = "ti,lp55231", }, | 
 | 	{}, | 
 | }; | 
 |  | 
 | MODULE_DEVICE_TABLE(of, of_lp5523_leds_match); | 
 | #endif | 
 |  | 
 | static struct i2c_driver lp5523_driver = { | 
 | 	.driver = { | 
 | 		.name	= "lp5523x", | 
 | 		.of_match_table = of_match_ptr(of_lp5523_leds_match), | 
 | 	}, | 
 | 	.probe		= lp5523_probe, | 
 | 	.remove		= lp5523_remove, | 
 | 	.id_table	= lp5523_id, | 
 | }; | 
 |  | 
 | module_i2c_driver(lp5523_driver); | 
 |  | 
 | MODULE_AUTHOR("Mathias Nyman <mathias.nyman@nokia.com>"); | 
 | MODULE_AUTHOR("Milo Kim <milo.kim@ti.com>"); | 
 | MODULE_DESCRIPTION("LP5523 LED engine"); | 
 | MODULE_LICENSE("GPL"); |