| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, AngeloGioacchino Del Regno |
| * <angelogioacchino.delregno@somainline.org> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include "msm8998.dtsi" |
| #include "pm8005.dtsi" |
| #include "pm8998.dtsi" |
| #include "pmi8998.dtsi" |
| |
| / { |
| model = "F(x)tec Pro1 (QX1000)"; |
| compatible = "fxtec,pro1", "qcom,msm8998"; |
| chassis-type = "handset"; |
| qcom,board-id = <0x02000b 0x10>; |
| |
| aliases { |
| serial0 = &blsp2_uart1; |
| serial1 = &blsp1_uart3; |
| }; |
| |
| /* |
| * Until we hook up type-c detection, we |
| * have to stick with this. But it works. |
| */ |
| extcon_usb: extcon-usb { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| gpio-hall-sensors { |
| compatible = "gpio-keys"; |
| label = "Hall sensors"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hall_sensor1_default>; |
| |
| event-hall-sensor1 { |
| label = "Keyboard Hall Sensor"; |
| gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>; |
| debounce-interval = <15>; |
| gpio-key,wakeup; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_KEYPAD_SLIDE>; |
| }; |
| }; |
| |
| gpio-kb-extra-keys { |
| compatible = "gpio-keys"; |
| label = "Keyboard extra keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_kb_pins_extra>; |
| |
| key-home { |
| label = "Home"; |
| gpios = <&tlmm 21 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOMEPAGE>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| key-super-l { |
| label = "Super Left"; |
| gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_FN>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| key-super-r { |
| label = "Super Right"; |
| gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_FN>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| key-shift { |
| label = "Shift"; |
| gpios = <&tlmm 114 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RIGHTSHIFT>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| key-ctrl { |
| label = "Ctrl"; |
| gpios = <&tlmm 128 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_LEFTCTRL>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| key-alt { |
| label = "Alt"; |
| gpios = <&tlmm 129 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_LEFTALT>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| label = "Side buttons"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>, |
| <&cam_snapshot_pin_a>; |
| button-vol-up { |
| label = "Volume Up"; |
| gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_VOLUMEUP>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| }; |
| |
| button-camera-snapshot { |
| label = "Camera Snapshot"; |
| gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA>; |
| debounce-interval = <15>; |
| }; |
| |
| button-camera-focus { |
| label = "Camera Focus"; |
| gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA_FOCUS>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| keyboard-leds { |
| compatible = "gpio-leds"; |
| |
| led-0 { |
| color = <LED_COLOR_ID_WHITE>; |
| default-state = "off"; |
| function = LED_FUNCTION_KBD_BACKLIGHT; |
| gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>; |
| label = "white:kbd_backlight"; |
| retain-state-suspended; |
| }; |
| |
| led-1 { |
| color = <LED_COLOR_ID_YELLOW>; |
| default-state = "off"; |
| function = LED_FUNCTION_CAPSLOCK; |
| gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; |
| label = "yellow:capslock"; |
| linux,default-trigger = "kbd-capslock"; |
| }; |
| }; |
| |
| reserved-memory { |
| cont_splash_mem: memory@9d400000 { |
| reg = <0x0 0x9d400000 0x0 0x2000000>; |
| no-map; |
| }; |
| |
| zap_shader_region: memory@f6400000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0xf6400000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| ramoops@ffc00000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xffc00000 0x0 0x100000>; |
| console-size = <0x60000>; |
| ecc-size = <16>; |
| ftrace-size = <0x10000>; |
| pmsg-size = <0x20000>; |
| record-size = <0x10000>; |
| }; |
| }; |
| |
| ts_vio_vreg: ts-vio-vreg { |
| compatible = "regulator-fixed"; |
| regulator-name = "ts_vio_reg"; |
| startup-delay-us = <2>; |
| enable-active-high; |
| gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_vio_default>; |
| regulator-always-on; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &blsp1_uart3 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn3990-bt"; |
| |
| vddio-supply = <&vreg_s4a_1p8>; |
| vddxo-supply = <&vreg_l7a_1p8>; |
| vddrf-supply = <&vreg_l17a_1p3>; |
| vddch0-supply = <&vreg_l25a_3p3>; |
| max-speed = <3200000>; |
| }; |
| }; |
| |
| &blsp1_uart3_on { |
| rx { |
| /delete-property/ bias-disable; |
| /* |
| * Configure a pull-up on 45 (RX). This is needed to |
| * avoid garbage data when the TX pin of the Bluetooth |
| * module is in tri-state (module powered off or not |
| * driving the signal yet). |
| */ |
| bias-pull-up; |
| }; |
| |
| cts { |
| /delete-property/ bias-disable; |
| /* |
| * Configure a pull-down on 47 (CTS) to match the pull |
| * of the Bluetooth module. |
| */ |
| bias-pull-down; |
| }; |
| }; |
| |
| &blsp2_uart1 { |
| status = "okay"; |
| }; |
| |
| &blsp2_i2c1 { |
| status = "okay"; |
| |
| touchscreen@14 { |
| compatible = "goodix,gt9286"; |
| reg = <0x14>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <125 IRQ_TYPE_LEVEL_LOW>; |
| reset-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>; |
| AVDD28-supply = <&vreg_l28_3p0>; |
| VDDIO-supply = <&ts_vio_vreg>; |
| pinctrl-names = "active"; |
| pinctrl-0 = <&ts_rst_n>, <&ts_int_n>; |
| }; |
| }; |
| |
| &etf { |
| status = "okay"; |
| }; |
| |
| &etm1 { |
| status = "okay"; |
| }; |
| |
| &etm2 { |
| status = "okay"; |
| }; |
| |
| &etm3 { |
| status = "okay"; |
| }; |
| |
| &etm4 { |
| status = "okay"; |
| }; |
| |
| &etm5 { |
| status = "okay"; |
| }; |
| |
| &etm6 { |
| status = "okay"; |
| }; |
| |
| &etm7 { |
| status = "okay"; |
| }; |
| |
| &etm8 { |
| status = "okay"; |
| }; |
| |
| &etr { |
| status = "okay"; |
| }; |
| |
| &funnel1 { |
| status = "okay"; |
| }; |
| |
| &funnel2 { |
| status = "okay"; |
| }; |
| |
| &funnel3 { |
| status = "okay"; |
| }; |
| |
| &funnel4 { |
| // FIXME: Figure out why clock late_initcall crashes the board with |
| // this enabled. |
| // status = "okay"; |
| }; |
| |
| &funnel5 { |
| // FIXME: Figure out why clock late_initcall crashes the board with |
| // this enabled. |
| // status = "okay"; |
| }; |
| |
| &pcie0 { |
| status = "okay"; |
| }; |
| |
| &pcie_phy { |
| status = "okay"; |
| }; |
| |
| &pm8005_regulators { |
| vdd_s1-supply = <&vph_pwr>; |
| |
| pm8005_s1: s1 { /* VDD_GFX supply */ |
| regulator-min-microvolt = <524000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-enable-ramp-delay = <500>; |
| |
| /* Hack until we rig up the gpu consumer */ |
| regulator-always-on; |
| }; |
| }; |
| |
| &pm8998_gpio { |
| vol_up_pin_a: vol-up-active-state { |
| pins = "gpio6"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_focus_pin_a: cam-focus-btn-active-state { |
| pins = "gpio7"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_snapshot_pin_a: cam-snapshot-btn-active-state { |
| pins = "gpio8"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| }; |
| |
| &pm8998_pon { |
| resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| bias-pull-up; |
| debounce = <15625>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| |
| &qusb2phy { |
| status = "okay"; |
| |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| }; |
| |
| &replicator1 { |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| pm8998-regulators { |
| compatible = "qcom,rpm-pm8998-regulators"; |
| |
| vdd_s1-supply = <&vph_pwr>; |
| vdd_s2-supply = <&vph_pwr>; |
| vdd_s3-supply = <&vph_pwr>; |
| vdd_s4-supply = <&vph_pwr>; |
| vdd_s5-supply = <&vph_pwr>; |
| vdd_s6-supply = <&vph_pwr>; |
| vdd_s7-supply = <&vph_pwr>; |
| vdd_s8-supply = <&vph_pwr>; |
| vdd_s9-supply = <&vph_pwr>; |
| vdd_s10-supply = <&vph_pwr>; |
| vdd_s11-supply = <&vph_pwr>; |
| vdd_s12-supply = <&vph_pwr>; |
| vdd_s13-supply = <&vph_pwr>; |
| vdd_l1_l27-supply = <&vreg_s7a_1p025>; |
| vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; |
| vdd_l3_l11-supply = <&vreg_s7a_1p025>; |
| vdd_l4_l5-supply = <&vreg_s7a_1p025>; |
| vdd_l6-supply = <&vreg_s5a_2p04>; |
| vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; |
| vdd_l9-supply = <&vreg_bob>; |
| vdd_l10_l23_l25-supply = <&vreg_bob>; |
| vdd_l13_l19_l21-supply = <&vreg_bob>; |
| vdd_l16_l28-supply = <&vreg_bob>; |
| vdd_l18_l22-supply = <&vreg_bob>; |
| vdd_l20_l24-supply = <&vreg_bob>; |
| vdd_l26-supply = <&vreg_s3a_1p35>; |
| vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; |
| |
| vreg_s3a_1p35: s3 { |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| }; |
| |
| vreg_s4a_1p8: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_s5a_2p04: s5 { |
| regulator-min-microvolt = <1904000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| vreg_s7a_1p025: s7 { |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1028000>; |
| }; |
| |
| vreg_l1a_0p875: l1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| }; |
| |
| vreg_l2a_1p2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vreg_l3a_1p0: l3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| vreg_l5a_0p8: l5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_l6a_1p8: l6 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <1808000>; |
| }; |
| |
| vreg_l7a_1p8: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l8a_1p2: l8 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vreg_l9a_1p8: l9 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| }; |
| |
| vreg_l10a_1p8: l10 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| }; |
| |
| vreg_l11a_1p0: l11 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| vreg_l12a_1p8: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l13a_2p95: l13 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| }; |
| |
| vreg_l14a_1p88: l14 { |
| regulator-min-microvolt = <1880000>; |
| regulator-max-microvolt = <1880000>; |
| }; |
| |
| vreg_l15a_1p8: l15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l16a_2p7: l16 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2704000>; |
| }; |
| |
| vreg_l17a_1p3: l17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| }; |
| |
| vreg_l18a_2p7: l18 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2704000>; |
| }; |
| |
| vreg_l19a_3p0: l19 { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| }; |
| |
| vreg_l20a_2p95: l20 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l21a_2p95: l21 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-system-load = <800000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l22a_2p85: l22 { |
| regulator-min-microvolt = <2864000>; |
| regulator-max-microvolt = <2864000>; |
| }; |
| |
| vreg_l23a_3p3: l23 { |
| regulator-min-microvolt = <3312000>; |
| regulator-max-microvolt = <3312000>; |
| }; |
| |
| vreg_l24a_3p075: l24 { |
| regulator-min-microvolt = <3088000>; |
| regulator-max-microvolt = <3088000>; |
| }; |
| |
| vreg_l25a_3p3: l25 { |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3312000>; |
| }; |
| |
| vreg_l26a_1p2: l26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l28_3p0: l28 { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_lvs2a_1p8: lvs2 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| }; |
| |
| pmi8998-regulators { |
| compatible = "qcom,rpm-pmi8998-regulators"; |
| |
| vdd_bob-supply = <&vph_pwr>; |
| |
| vreg_bob: bob { |
| regulator-min-microvolt = <3312000>; |
| regulator-max-microvolt = <3600000>; |
| }; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| status = "okay"; |
| }; |
| |
| &remoteproc_mss { |
| status = "okay"; |
| }; |
| |
| &remoteproc_slpi { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>; |
| |
| mdp_vsync_n: mdp-vsync-n { |
| pins = "gpio10"; |
| function = "mdp_vsync_a"; |
| bias-pull-down; |
| drive-strength = <2>; |
| }; |
| |
| gpio_kb_pins_extra: gpio-kb-pins-extra { |
| pins = "gpio21", "gpio32", "gpio33", "gpio114", |
| "gpio128", "gpio129"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| ts_vio_default: ts-vio-def { |
| pins = "gpio81"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| ts_rst_n: ts-rst-n { |
| pins = "gpio89"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <8>; |
| }; |
| |
| hall_sensor1_default: hall-sensor1-def { |
| pins = "gpio124"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| input-enable; |
| }; |
| |
| ts_int_n: ts-int-n { |
| pins = "gpio125"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <8>; |
| }; |
| }; |
| |
| &sdhc2 { |
| status = "okay"; |
| cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>; |
| |
| vmmc-supply = <&vreg_l21a_2p95>; |
| vqmmc-supply = <&vreg_l13a_2p95>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on &sdc2_cd>; |
| pinctrl-1 = <&sdc2_off &sdc2_cd>; |
| }; |
| |
| &stm { |
| status = "okay"; |
| }; |
| |
| &ufshc { |
| status = "okay"; |
| vcc-supply = <&vreg_l20a_2p95>; |
| vccq-supply = <&vreg_l26a_1p2>; |
| vccq2-supply = <&vreg_s4a_1p8>; |
| vcc-max-microamp = <750000>; |
| vccq-max-microamp = <560000>; |
| vccq2-max-microamp = <750000>; |
| }; |
| |
| &ufsphy { |
| status = "okay"; |
| vdda-phy-supply = <&vreg_l1a_0p875>; |
| vdda-pll-supply = <&vreg_l2a_1p2>; |
| vddp-ref-clk-supply = <&vreg_l26a_1p2>; |
| }; |
| |
| &usb3 { |
| status = "okay"; |
| }; |
| |
| &usb3_dwc3 { |
| dr_mode = "peripheral"; |
| extcon = <&extcon_usb>; |
| }; |
| |
| &usb3phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l1a_0p875>; |
| vdda-pll-supply = <&vreg_l2a_1p2>; |
| }; |
| |
| /* GT9286 analog supply */ |
| &vreg_l28_3p0 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| &wifi { |
| status = "okay"; |
| |
| vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; |
| vdd-1.8-xo-supply = <&vreg_l7a_1p8>; |
| vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; |
| vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; |
| }; |
