blob: 8978dc9a58b748c9da1a4f65d2c1ecaffbf8e523 [file] [log] [blame]
/*
* Freescale lpuart serial port driver
*
* Copyright 2012-2013 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#if defined(CONFIG_SERIAL_FSL_LPUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/clk.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/console.h>
#include <linux/serial_core.h>
#include <linux/tty_flip.h>
/* All registers are 8-bit width */
#define UARTBDH 0x00
#define UARTBDL 0x01
#define UARTCR1 0x02
#define UARTCR2 0x03
#define UARTSR1 0x04
#define UARTCR3 0x06
#define UARTDR 0x07
#define UARTCR4 0x0a
#define UARTCR5 0x0b
#define UARTMODEM 0x0d
#define UARTPFIFO 0x10
#define UARTCFIFO 0x11
#define UARTSFIFO 0x12
#define UARTTWFIFO 0x13
#define UARTTCFIFO 0x14
#define UARTRWFIFO 0x15
#define UARTBDH_LBKDIE 0x80
#define UARTBDH_RXEDGIE 0x40
#define UARTBDH_SBR_MASK 0x1f
#define UARTCR1_LOOPS 0x80
#define UARTCR1_RSRC 0x20
#define UARTCR1_M 0x10
#define UARTCR1_WAKE 0x08
#define UARTCR1_ILT 0x04
#define UARTCR1_PE 0x02
#define UARTCR1_PT 0x01
#define UARTCR2_TIE 0x80
#define UARTCR2_TCIE 0x40
#define UARTCR2_RIE 0x20
#define UARTCR2_ILIE 0x10
#define UARTCR2_TE 0x08
#define UARTCR2_RE 0x04
#define UARTCR2_RWU 0x02
#define UARTCR2_SBK 0x01
#define UARTSR1_TDRE 0x80
#define UARTSR1_TC 0x40
#define UARTSR1_RDRF 0x20
#define UARTSR1_IDLE 0x10
#define UARTSR1_OR 0x08
#define UARTSR1_NF 0x04
#define UARTSR1_FE 0x02
#define UARTSR1_PE 0x01
#define UARTCR3_R8 0x80
#define UARTCR3_T8 0x40
#define UARTCR3_TXDIR 0x20
#define UARTCR3_TXINV 0x10
#define UARTCR3_ORIE 0x08
#define UARTCR3_NEIE 0x04
#define UARTCR3_FEIE 0x02
#define UARTCR3_PEIE 0x01
#define UARTCR4_MAEN1 0x80
#define UARTCR4_MAEN2 0x40
#define UARTCR4_M10 0x20
#define UARTCR4_BRFA_MASK 0x1f
#define UARTCR4_BRFA_OFF 0
#define UARTCR5_TDMAS 0x80
#define UARTCR5_RDMAS 0x20
#define UARTMODEM_RXRTSE 0x08
#define UARTMODEM_TXRTSPOL 0x04
#define UARTMODEM_TXRTSE 0x02
#define UARTMODEM_TXCTSE 0x01
#define UARTPFIFO_TXFE 0x80
#define UARTPFIFO_FIFOSIZE_MASK 0x7
#define UARTPFIFO_TXSIZE_OFF 4
#define UARTPFIFO_RXFE 0x08
#define UARTPFIFO_RXSIZE_OFF 0
#define UARTCFIFO_TXFLUSH 0x80
#define UARTCFIFO_RXFLUSH 0x40
#define UARTCFIFO_RXOFE 0x04
#define UARTCFIFO_TXOFE 0x02
#define UARTCFIFO_RXUFE 0x01
#define UARTSFIFO_TXEMPT 0x80
#define UARTSFIFO_RXEMPT 0x40
#define UARTSFIFO_RXOF 0x04
#define UARTSFIFO_TXOF 0x02
#define UARTSFIFO_RXUF 0x01
#define DRIVER_NAME "fsl-lpuart"
#define DEV_NAME "ttyLP"
#define UART_NR 6
struct lpuart_port {
struct uart_port port;
struct clk *clk;
unsigned int txfifo_size;
unsigned int rxfifo_size;
};
static struct of_device_id lpuart_dt_ids[] = {
{
.compatible = "fsl,vf610-lpuart",
},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, lpuart_dt_ids);
static void lpuart_stop_tx(struct uart_port *port)
{
unsigned char temp;
temp = readb(port->membase + UARTCR2);
temp &= ~(UARTCR2_TIE | UARTCR2_TCIE);
writeb(temp, port->membase + UARTCR2);
}
static void lpuart_stop_rx(struct uart_port *port)
{
unsigned char temp;
temp = readb(port->membase + UARTCR2);
writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2);
}
static void lpuart_enable_ms(struct uart_port *port)
{
}
static inline void lpuart_transmit_buffer(struct lpuart_port *sport)
{
struct circ_buf *xmit = &sport->port.state->xmit;
while (!uart_circ_empty(xmit) &&
(readb(sport->port.membase + UARTTCFIFO) < sport->txfifo_size)) {
writeb(xmit->buf[xmit->tail], sport->port.membase + UARTDR);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
sport->port.icount.tx++;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&sport->port);
if (uart_circ_empty(xmit))
lpuart_stop_tx(&sport->port);
}
static void lpuart_start_tx(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
unsigned char temp;
temp = readb(port->membase + UARTCR2);
writeb(temp | UARTCR2_TIE, port->membase + UARTCR2);
if (readb(port->membase + UARTSR1) & UARTSR1_TDRE)
lpuart_transmit_buffer(sport);
}
static irqreturn_t lpuart_txint(int irq, void *dev_id)
{
struct lpuart_port *sport = dev_id;
struct circ_buf *xmit = &sport->port.state->xmit;
unsigned long flags;
spin_lock_irqsave(&sport->port.lock, flags);
if (sport->port.x_char) {
writeb(sport->port.x_char, sport->port.membase + UARTDR);
goto out;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
lpuart_stop_tx(&sport->port);
goto out;
}
lpuart_transmit_buffer(sport);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&sport->port);
out:
spin_unlock_irqrestore(&sport->port.lock, flags);
return IRQ_HANDLED;
}
static irqreturn_t lpuart_rxint(int irq, void *dev_id)
{
struct lpuart_port *sport = dev_id;
unsigned int flg, ignored = 0;
struct tty_port *port = &sport->port.state->port;
unsigned long flags;
unsigned char rx, sr;
spin_lock_irqsave(&sport->port.lock, flags);
while (!(readb(sport->port.membase + UARTSFIFO) & UARTSFIFO_RXEMPT)) {
flg = TTY_NORMAL;
sport->port.icount.rx++;
/*
* to clear the FE, OR, NF, FE, PE flags,
* read SR1 then read DR
*/
sr = readb(sport->port.membase + UARTSR1);
rx = readb(sport->port.membase + UARTDR);
if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
continue;
if (sr & (UARTSR1_PE | UARTSR1_OR | UARTSR1_FE)) {
if (sr & UARTSR1_PE)
sport->port.icount.parity++;
else if (sr & UARTSR1_FE)
sport->port.icount.frame++;
if (sr & UARTSR1_OR)
sport->port.icount.overrun++;
if (sr & sport->port.ignore_status_mask) {
if (++ignored > 100)
goto out;
continue;
}
sr &= sport->port.read_status_mask;
if (sr & UARTSR1_PE)
flg = TTY_PARITY;
else if (sr & UARTSR1_FE)
flg = TTY_FRAME;
if (sr & UARTSR1_OR)
flg = TTY_OVERRUN;
#ifdef SUPPORT_SYSRQ
sport->port.sysrq = 0;
#endif
}
tty_insert_flip_char(port, rx, flg);
}
out:
spin_unlock_irqrestore(&sport->port.lock, flags);
tty_flip_buffer_push(port);
return IRQ_HANDLED;
}
static irqreturn_t lpuart_int(int irq, void *dev_id)
{
struct lpuart_port *sport = dev_id;
unsigned char sts;
sts = readb(sport->port.membase + UARTSR1);
if (sts & UARTSR1_RDRF)
lpuart_rxint(irq, dev_id);
if (sts & UARTSR1_TDRE &&
!(readb(sport->port.membase + UARTCR5) & UARTCR5_TDMAS))
lpuart_txint(irq, dev_id);
return IRQ_HANDLED;
}
/* return TIOCSER_TEMT when transmitter is not busy */
static unsigned int lpuart_tx_empty(struct uart_port *port)
{
return (readb(port->membase + UARTSR1) & UARTSR1_TC) ?
TIOCSER_TEMT : 0;
}
static unsigned int lpuart_get_mctrl(struct uart_port *port)
{
unsigned int temp = 0;
unsigned char reg;
reg = readb(port->membase + UARTMODEM);
if (reg & UARTMODEM_TXCTSE)
temp |= TIOCM_CTS;
if (reg & UARTMODEM_RXRTSE)
temp |= TIOCM_RTS;
return temp;
}
static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
unsigned char temp;
temp = readb(port->membase + UARTMODEM) &
~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
if (mctrl & TIOCM_RTS)
temp |= UARTMODEM_RXRTSE;
if (mctrl & TIOCM_CTS)
temp |= UARTMODEM_TXCTSE;
writeb(temp, port->membase + UARTMODEM);
}
static void lpuart_break_ctl(struct uart_port *port, int break_state)
{
unsigned char temp;
temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
if (break_state != 0)
temp |= UARTCR2_SBK;
writeb(temp, port->membase + UARTCR2);
}
static void lpuart_setup_watermark(struct lpuart_port *sport)
{
unsigned char val, cr2;
unsigned char cr2_saved;
cr2 = readb(sport->port.membase + UARTCR2);
cr2_saved = cr2;
cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_TE |
UARTCR2_RIE | UARTCR2_RE);
writeb(cr2, sport->port.membase + UARTCR2);
/* determine FIFO size and enable FIFO mode */
val = readb(sport->port.membase + UARTPFIFO);
sport->txfifo_size = 0x1 << (((val >> UARTPFIFO_TXSIZE_OFF) &
UARTPFIFO_FIFOSIZE_MASK) + 1);
sport->rxfifo_size = 0x1 << (((val >> UARTPFIFO_RXSIZE_OFF) &
UARTPFIFO_FIFOSIZE_MASK) + 1);
writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
sport->port.membase + UARTPFIFO);
/* flush Tx and Rx FIFO */
writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH,
sport->port.membase + UARTCFIFO);
writeb(2, sport->port.membase + UARTTWFIFO);
writeb(1, sport->port.membase + UARTRWFIFO);
/* Restore cr2 */
writeb(cr2_saved, sport->port.membase + UARTCR2);
}
static int lpuart_startup(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
int ret;
unsigned long flags;
unsigned char temp;
ret = devm_request_irq(port->dev, port->irq, lpuart_int, 0,
DRIVER_NAME, sport);
if (ret)
return ret;
spin_lock_irqsave(&sport->port.lock, flags);
lpuart_setup_watermark(sport);
temp = readb(sport->port.membase + UARTCR2);
temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
writeb(temp, sport->port.membase + UARTCR2);
spin_unlock_irqrestore(&sport->port.lock, flags);
return 0;
}
static void lpuart_shutdown(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
unsigned char temp;
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
/* disable Rx/Tx and interrupts */
temp = readb(port->membase + UARTCR2);
temp &= ~(UARTCR2_TE | UARTCR2_RE |
UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
writeb(temp, port->membase + UARTCR2);
spin_unlock_irqrestore(&port->lock, flags);
devm_free_irq(port->dev, port->irq, sport);
}
static void
lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
unsigned long flags;
unsigned char cr1, old_cr1, old_cr2, cr4, bdh, modem;
unsigned int baud;
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
unsigned int sbr, brfa;
cr1 = old_cr1 = readb(sport->port.membase + UARTCR1);
old_cr2 = readb(sport->port.membase + UARTCR2);
cr4 = readb(sport->port.membase + UARTCR4);
bdh = readb(sport->port.membase + UARTBDH);
modem = readb(sport->port.membase + UARTMODEM);
/*
* only support CS8 and CS7, and for CS7 must enable PE.
* supported mode:
* - (7,e/o,1)
* - (8,n,1)
* - (8,m/s,1)
* - (8,e/o,1)
*/
while ((termios->c_cflag & CSIZE) != CS8 &&
(termios->c_cflag & CSIZE) != CS7) {
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= old_csize;
old_csize = CS8;
}
if ((termios->c_cflag & CSIZE) == CS8 ||
(termios->c_cflag & CSIZE) == CS7)
cr1 = old_cr1 & ~UARTCR1_M;
if (termios->c_cflag & CMSPAR) {
if ((termios->c_cflag & CSIZE) != CS8) {
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
}
cr1 |= UARTCR1_M;
}
if (termios->c_cflag & CRTSCTS) {
modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
} else {
termios->c_cflag &= ~CRTSCTS;
modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
}
if (termios->c_cflag & CSTOPB)
termios->c_cflag &= ~CSTOPB;
/* parity must be enabled when CS7 to match 8-bits format */
if ((termios->c_cflag & CSIZE) == CS7)
termios->c_cflag |= PARENB;
if ((termios->c_cflag & PARENB)) {
if (termios->c_cflag & CMSPAR) {
cr1 &= ~UARTCR1_PE;
cr1 |= UARTCR1_M;
} else {
cr1 |= UARTCR1_PE;
if ((termios->c_cflag & CSIZE) == CS8)
cr1 |= UARTCR1_M;
if (termios->c_cflag & PARODD)
cr1 |= UARTCR1_PT;
else
cr1 &= ~UARTCR1_PT;
}
}
/* ask the core to calculate the divisor */
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask = 0;
if (termios->c_iflag & INPCK)
sport->port.read_status_mask |= (UARTSR1_FE | UARTSR1_PE);
if (termios->c_iflag & (BRKINT | PARMRK))
sport->port.read_status_mask |= UARTSR1_FE;
/* characters to ignore */
sport->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= UARTSR1_PE;
if (termios->c_iflag & IGNBRK) {
sport->port.ignore_status_mask |= UARTSR1_FE;
/*
* if we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= UARTSR1_OR;
}
/* update the per-port timeout */
uart_update_timeout(port, termios->c_cflag, baud);
/* wait transmit engin complete */
while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
barrier();
/* disable transmit and receive */
writeb(old_cr2 & ~(UARTCR2_TE | UARTCR2_RE),
sport->port.membase + UARTCR2);
sbr = sport->port.uartclk / (16 * baud);
brfa = ((sport->port.uartclk - (16 * sbr * baud)) * 2) / baud;
bdh &= ~UARTBDH_SBR_MASK;
bdh |= (sbr >> 8) & 0x1F;
cr4 &= ~UARTCR4_BRFA_MASK;
brfa &= UARTCR4_BRFA_MASK;
writeb(cr4 | brfa, sport->port.membase + UARTCR4);
writeb(bdh, sport->port.membase + UARTBDH);
writeb(sbr & 0xFF, sport->port.membase + UARTBDL);
writeb(cr1, sport->port.membase + UARTCR1);
writeb(modem, sport->port.membase + UARTMODEM);
/* restore control register */
writeb(old_cr2, sport->port.membase + UARTCR2);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static const char *lpuart_type(struct uart_port *port)
{
return "FSL_LPUART";
}
static void lpuart_release_port(struct uart_port *port)
{
/* nothing to do */
}
static int lpuart_request_port(struct uart_port *port)
{
return 0;
}
/* configure/autoconfigure the port */
static void lpuart_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE)
port->type = PORT_LPUART;
}
static int lpuart_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_LPUART)
ret = -EINVAL;
if (port->irq != ser->irq)
ret = -EINVAL;
if (ser->io_type != UPIO_MEM)
ret = -EINVAL;
if (port->uartclk / 16 != ser->baud_base)
ret = -EINVAL;
if (port->iobase != ser->port)
ret = -EINVAL;
if (ser->hub6 != 0)
ret = -EINVAL;
return ret;
}
static struct uart_ops lpuart_pops = {
.tx_empty = lpuart_tx_empty,
.set_mctrl = lpuart_set_mctrl,
.get_mctrl = lpuart_get_mctrl,
.stop_tx = lpuart_stop_tx,
.start_tx = lpuart_start_tx,
.stop_rx = lpuart_stop_rx,
.enable_ms = lpuart_enable_ms,
.break_ctl = lpuart_break_ctl,
.startup = lpuart_startup,
.shutdown = lpuart_shutdown,
.set_termios = lpuart_set_termios,
.type = lpuart_type,
.request_port = lpuart_request_port,
.release_port = lpuart_release_port,
.config_port = lpuart_config_port,
.verify_port = lpuart_verify_port,
};
static struct lpuart_port *lpuart_ports[UART_NR];
#ifdef CONFIG_SERIAL_FSL_LPUART_CONSOLE
static void lpuart_console_putchar(struct uart_port *port, int ch)
{
while (!(readb(port->membase + UARTSR1) & UARTSR1_TDRE))
barrier();
writeb(ch, port->membase + UARTDR);
}
static void
lpuart_console_write(struct console *co, const char *s, unsigned int count)
{
struct lpuart_port *sport = lpuart_ports[co->index];
unsigned char old_cr2, cr2;
/* first save CR2 and then disable interrupts */
cr2 = old_cr2 = readb(sport->port.membase + UARTCR2);
cr2 |= (UARTCR2_TE | UARTCR2_RE);
cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
writeb(cr2, sport->port.membase + UARTCR2);
uart_console_write(&sport->port, s, count, lpuart_console_putchar);
/* wait for transmitter finish complete and restore CR2 */
while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
barrier();
writeb(old_cr2, sport->port.membase + UARTCR2);
}
/*
* if the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
*/
static void __init
lpuart_console_get_options(struct lpuart_port *sport, int *baud,
int *parity, int *bits)
{
unsigned char cr, bdh, bdl, brfa;
unsigned int sbr, uartclk, baud_raw;
cr = readb(sport->port.membase + UARTCR2);
cr &= UARTCR2_TE | UARTCR2_RE;
if (!cr)
return;
/* ok, the port was enabled */
cr = readb(sport->port.membase + UARTCR1);
*parity = 'n';
if (cr & UARTCR1_PE) {
if (cr & UARTCR1_PT)
*parity = 'o';
else
*parity = 'e';
}
if (cr & UARTCR1_M)
*bits = 9;
else
*bits = 8;
bdh = readb(sport->port.membase + UARTBDH);
bdh &= UARTBDH_SBR_MASK;
bdl = readb(sport->port.membase + UARTBDL);
sbr = bdh;
sbr <<= 8;
sbr |= bdl;
brfa = readb(sport->port.membase + UARTCR4);
brfa &= UARTCR4_BRFA_MASK;
uartclk = clk_get_rate(sport->clk);
/*
* baud = mod_clk/(16*(sbr[13]+(brfa)/32)
*/
baud_raw = uartclk / (16 * (sbr + brfa / 32));
if (*baud != baud_raw)
printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
"from %d to %d\n", baud_raw, *baud);
}
static int __init lpuart_console_setup(struct console *co, char *options)
{
struct lpuart_port *sport;
int baud = 115200;
int bits = 8;
int parity = 'n';
int flow = 'n';
/*
* check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index == -1 || co->index >= ARRAY_SIZE(lpuart_ports))
co->index = 0;
sport = lpuart_ports[co->index];
if (sport == NULL)
return -ENODEV;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
lpuart_console_get_options(sport, &baud, &parity, &bits);
lpuart_setup_watermark(sport);
return uart_set_options(&sport->port, co, baud, parity, bits, flow);
}
static struct uart_driver lpuart_reg;
static struct console lpuart_console = {
.name = DEV_NAME,
.write = lpuart_console_write,
.device = uart_console_device,
.setup = lpuart_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &lpuart_reg,
};
#define LPUART_CONSOLE (&lpuart_console)
#else
#define LPUART_CONSOLE NULL
#endif
static struct uart_driver lpuart_reg = {
.owner = THIS_MODULE,
.driver_name = DRIVER_NAME,
.dev_name = DEV_NAME,
.nr = ARRAY_SIZE(lpuart_ports),
.cons = LPUART_CONSOLE,
};
static int lpuart_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct lpuart_port *sport;
struct resource *res;
int ret;
sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
if (!sport)
return -ENOMEM;
pdev->dev.coherent_dma_mask = 0;
ret = of_alias_get_id(np, "serial");
if (ret < 0) {
dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
return ret;
}
sport->port.line = ret;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
return -ENODEV;
sport->port.mapbase = res->start;
sport->port.membase = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(sport->port.membase))
return PTR_ERR(sport->port.membase);
sport->port.dev = &pdev->dev;
sport->port.type = PORT_LPUART;
sport->port.iotype = UPIO_MEM;
sport->port.irq = platform_get_irq(pdev, 0);
sport->port.ops = &lpuart_pops;
sport->port.flags = UPF_BOOT_AUTOCONF;
sport->clk = devm_clk_get(&pdev->dev, "ipg");
if (IS_ERR(sport->clk)) {
ret = PTR_ERR(sport->clk);
dev_err(&pdev->dev, "failed to get uart clk: %d\n", ret);
return ret;
}
ret = clk_prepare_enable(sport->clk);
if (ret) {
dev_err(&pdev->dev, "failed to enable uart clk: %d\n", ret);
return ret;
}
sport->port.uartclk = clk_get_rate(sport->clk);
lpuart_ports[sport->port.line] = sport;
platform_set_drvdata(pdev, &sport->port);
ret = uart_add_one_port(&lpuart_reg, &sport->port);
if (ret) {
clk_disable_unprepare(sport->clk);
return ret;
}
return 0;
}
static int lpuart_remove(struct platform_device *pdev)
{
struct lpuart_port *sport = platform_get_drvdata(pdev);
uart_remove_one_port(&lpuart_reg, &sport->port);
clk_disable_unprepare(sport->clk);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int lpuart_suspend(struct device *dev)
{
struct lpuart_port *sport = dev_get_drvdata(dev);
uart_suspend_port(&lpuart_reg, &sport->port);
return 0;
}
static int lpuart_resume(struct device *dev)
{
struct lpuart_port *sport = dev_get_drvdata(dev);
uart_resume_port(&lpuart_reg, &sport->port);
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(lpuart_pm_ops, lpuart_suspend, lpuart_resume);
static struct platform_driver lpuart_driver = {
.probe = lpuart_probe,
.remove = lpuart_remove,
.driver = {
.name = "fsl-lpuart",
.owner = THIS_MODULE,
.of_match_table = lpuart_dt_ids,
.pm = &lpuart_pm_ops,
},
};
static int __init lpuart_serial_init(void)
{
int ret;
pr_info("serial: Freescale lpuart driver\n");
ret = uart_register_driver(&lpuart_reg);
if (ret)
return ret;
ret = platform_driver_register(&lpuart_driver);
if (ret)
uart_unregister_driver(&lpuart_reg);
return ret;
}
static void __exit lpuart_serial_exit(void)
{
platform_driver_unregister(&lpuart_driver);
uart_unregister_driver(&lpuart_reg);
}
module_init(lpuart_serial_init);
module_exit(lpuart_serial_exit);
MODULE_DESCRIPTION("Freescale lpuart serial port driver");
MODULE_LICENSE("GPL v2");