blob: 04da07ae4420846144822a3dab6a901eb97b6384 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device Tree file for CZ.NIC Turris Mox Board
* 2019 by Marek BehĂșn <kabel@kernel.org>
*/
/dts-v1/;
#include <dt-bindings/bus/moxtet.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "armada-372x.dtsi"
/ {
model = "CZ.NIC Turris Mox Board";
compatible = "cznic,turris-mox", "marvell,armada3720",
"marvell,armada3710";
aliases {
spi0 = &spi0;
ethernet1 = &eth1;
mmc0 = &sdhci0;
mmc1 = &sdhci1;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
leds {
compatible = "gpio-leds";
red {
label = "mox:red:activity";
gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-on";
};
};
gpio-keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
exp_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
regulator-name = "usb3-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
};
vsdc_reg: vsdc-reg {
compatible = "regulator-gpio";
regulator-name = "vsdc";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <1800000 0x1
3300000 0x0>;
enable-active-high;
};
vsdio_reg: vsdio-reg {
compatible = "regulator-gpio";
regulator-name = "vsdio";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <1800000 0x1
3300000 0x0>;
enable-active-high;
};
sdhci1_pwrseq: sdhci1-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>;
status = "okay";
};
sfp: sfp {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
rate-select0-gpio = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
/* enabled by U-Boot if SFP module is present */
status = "disabled";
};
firmware {
armada-3700-rwtm {
compatible = "marvell,armada-3700-rwtm-firmware", "cznic,turris-mox-rwtm";
};
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <100000>;
/delete-property/ mrvl,i2c-fast-mode;
status = "okay";
rtc@6f {
compatible = "microchip,mcp7940x";
reg = <0x6f>;
};
};
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
status = "okay";
reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
/*
* U-Boot port for Turris Mox has a bug which always expects that "ranges" DT property
* contains exactly 2 ranges with 3 (child) address cells, 2 (parent) address cells and
* 2 size cells and also expects that the second range starts at 16 MB offset. If these
* conditions are not met then U-Boot crashes during loading kernel DTB file. PCIe address
* space is 128 MB long, so the best split between MEM and IO is to use fixed 16 MB window
* for IO and the rest 112 MB (64+32+16) for MEM, despite that maximal IO size is just 64 kB.
* This bug is not present in U-Boot ports for other Armada 3700 devices and is fixed in
* U-Boot version 2021.07. See relevant U-Boot commits (the last one contains fix):
* https://source.denx.de/u-boot/u-boot/-/commit/cb2ddb291ee6fcbddd6d8f4ff49089dfe580f5d7
* https://source.denx.de/u-boot/u-boot/-/commit/c64ac3b3185aeb3846297ad7391fc6df8ecd73bf
* https://source.denx.de/u-boot/u-boot/-/commit/4a82fca8e330157081fc132a591ebd99ba02ee33
*/
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0xe8000000 0 0xe8000000 0 0x01000000 /* Port 0 IO */
0x82000000 0 0xe9000000 0 0xe9000000 0 0x07000000>; /* Port 0 MEM */
/* enabled by U-Boot if PCIe module is present */
status = "disabled";
};
&uart0 {
status = "okay";
};
&eth0 {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii-id";
phy-handle = <&phy1>;
status = "okay";
};
&eth1 {
phy-mode = "2500base-x";
managed = "in-band-status";
phys = <&comphy0 1>;
};
&sdhci0 {
wp-inverted;
bus-width = <4>;
cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>;
vqmmc-supply = <&vsdc_reg>;
marvell,pad-type = "sd";
status = "okay";
};
&sdhci1 {
pinctrl-names = "default";
pinctrl-0 = <&sdio_pins>;
non-removable;
bus-width = <4>;
marvell,pad-type = "sd";
vqmmc-supply = <&vsdio_reg>;
mmc-pwrseq = <&sdhci1_pwrseq>;
/* forbid SDR104 for FCC purposes */
sdhci-caps-mask = <0x2 0x0>;
status = "okay";
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>;
assigned-clocks = <&nb_periph_clk 7>;
assigned-clock-parents = <&tbg 1>;
assigned-clock-rates = <20000000>;
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "secure-firmware";
reg = <0x0 0x20000>;
};
partition@20000 {
label = "a53-firmware";
reg = <0x20000 0x160000>;
};
partition@180000 {
label = "u-boot-env";
reg = <0x180000 0x10000>;
};
partition@190000 {
label = "Rescue system";
reg = <0x190000 0x660000>;
};
partition@7f0000 {
label = "dtb";
reg = <0x7f0000 0x10000>;
};
};
};
moxtet: moxtet@1 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "cznic,moxtet";
reg = <1>;
reset-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
spi-max-frequency = <10000000>;
spi-cpol;
spi-cpha;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&gpiosb>;
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
moxtet_sfp: gpio@0 {
compatible = "cznic,moxtet-gpio";
gpio-controller;
#gpio-cells = <2>;
reg = <0>;
status = "disabled";
};
};
};
&usb2 {
status = "okay";
};
&comphy2 {
connector {
compatible = "usb-a-connector";
phy-supply = <&exp_usb3_vbus>;
};
};
&usb3 {
status = "okay";
phys = <&comphy2 0>;
};
&mdio {
pinctrl-names = "default";
pinctrl-0 = <&smi_pins>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
/* switch nodes are enabled by U-Boot if modules are present */
switch0@10 {
compatible = "marvell,mv88e6190";
reg = <0x10 0>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(0)>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch0phy1: switch0phy1@1 {
reg = <0x1>;
};
switch0phy2: switch0phy2@2 {
reg = <0x2>;
};
switch0phy3: switch0phy3@3 {
reg = <0x3>;
};
switch0phy4: switch0phy4@4 {
reg = <0x4>;
};
switch0phy5: switch0phy5@5 {
reg = <0x5>;
};
switch0phy6: switch0phy6@6 {
reg = <0x6>;
};
switch0phy7: switch0phy7@7 {
reg = <0x7>;
};
switch0phy8: switch0phy8@8 {
reg = <0x8>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1>;
};
port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2>;
};
port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3>;
};
port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4>;
};
port@5 {
reg = <0x5>;
label = "lan5";
phy-handle = <&switch0phy5>;
};
port@6 {
reg = <0x6>;
label = "lan6";
phy-handle = <&switch0phy6>;
};
port@7 {
reg = <0x7>;
label = "lan7";
phy-handle = <&switch0phy7>;
};
port@8 {
reg = <0x8>;
label = "lan8";
phy-handle = <&switch0phy8>;
};
port@9 {
reg = <0x9>;
label = "cpu";
ethernet = <&eth1>;
phy-mode = "2500base-x";
managed = "in-band-status";
};
switch0port10: port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch1port9 &switch2port9>;
status = "disabled";
};
port-sfp@a {
reg = <0xa>;
label = "sfp";
sfp = <&sfp>;
phy-mode = "sgmii";
managed = "in-band-status";
status = "disabled";
};
};
};
switch0@2 {
compatible = "marvell,mv88e6085";
reg = <0x2 0>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch0phy1_topaz: switch0phy1@11 {
reg = <0x11>;
};
switch0phy2_topaz: switch0phy2@12 {
reg = <0x12>;
};
switch0phy3_topaz: switch0phy3@13 {
reg = <0x13>;
};
switch0phy4_topaz: switch0phy4@14 {
reg = <0x14>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1_topaz>;
};
port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2_topaz>;
};
port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3_topaz>;
};
port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4_topaz>;
};
port@5 {
reg = <0x5>;
label = "cpu";
phy-mode = "2500base-x";
managed = "in-band-status";
ethernet = <&eth1>;
};
};
};
switch1@11 {
compatible = "marvell,mv88e6190";
reg = <0x11 0>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(1)>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch1phy1: switch1phy1@1 {
reg = <0x1>;
};
switch1phy2: switch1phy2@2 {
reg = <0x2>;
};
switch1phy3: switch1phy3@3 {
reg = <0x3>;
};
switch1phy4: switch1phy4@4 {
reg = <0x4>;
};
switch1phy5: switch1phy5@5 {
reg = <0x5>;
};
switch1phy6: switch1phy6@6 {
reg = <0x6>;
};
switch1phy7: switch1phy7@7 {
reg = <0x7>;
};
switch1phy8: switch1phy8@8 {
reg = <0x8>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1>;
};
port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2>;
};
port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3>;
};
port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4>;
};
port@5 {
reg = <0x5>;
label = "lan13";
phy-handle = <&switch1phy5>;
};
port@6 {
reg = <0x6>;
label = "lan14";
phy-handle = <&switch1phy6>;
};
port@7 {
reg = <0x7>;
label = "lan15";
phy-handle = <&switch1phy7>;
};
port@8 {
reg = <0x8>;
label = "lan16";
phy-handle = <&switch1phy8>;
};
switch1port9: port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch0port10>;
};
switch1port10: port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch2port9>;
status = "disabled";
};
port-sfp@a {
reg = <0xa>;
label = "sfp";
sfp = <&sfp>;
phy-mode = "sgmii";
managed = "in-band-status";
status = "disabled";
};
};
};
switch1@2 {
compatible = "marvell,mv88e6085";
reg = <0x2 0>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch1phy1_topaz: switch1phy1@11 {
reg = <0x11>;
};
switch1phy2_topaz: switch1phy2@12 {
reg = <0x12>;
};
switch1phy3_topaz: switch1phy3@13 {
reg = <0x13>;
};
switch1phy4_topaz: switch1phy4@14 {
reg = <0x14>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1_topaz>;
};
port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2_topaz>;
};
port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3_topaz>;
};
port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4_topaz>;
};
port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch0port10>;
};
};
};
switch2@12 {
compatible = "marvell,mv88e6190";
reg = <0x12 0>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(2)>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch2phy1: switch2phy1@1 {
reg = <0x1>;
};
switch2phy2: switch2phy2@2 {
reg = <0x2>;
};
switch2phy3: switch2phy3@3 {
reg = <0x3>;
};
switch2phy4: switch2phy4@4 {
reg = <0x4>;
};
switch2phy5: switch2phy5@5 {
reg = <0x5>;
};
switch2phy6: switch2phy6@6 {
reg = <0x6>;
};
switch2phy7: switch2phy7@7 {
reg = <0x7>;
};
switch2phy8: switch2phy8@8 {
reg = <0x8>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1>;
};
port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2>;
};
port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3>;
};
port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4>;
};
port@5 {
reg = <0x5>;
label = "lan21";
phy-handle = <&switch2phy5>;
};
port@6 {
reg = <0x6>;
label = "lan22";
phy-handle = <&switch2phy6>;
};
port@7 {
reg = <0x7>;
label = "lan23";
phy-handle = <&switch2phy7>;
};
port@8 {
reg = <0x8>;
label = "lan24";
phy-handle = <&switch2phy8>;
};
switch2port9: port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch1port10 &switch0port10>;
};
port-sfp@a {
reg = <0xa>;
label = "sfp";
sfp = <&sfp>;
phy-mode = "sgmii";
managed = "in-band-status";
status = "disabled";
};
};
};
switch2@2 {
compatible = "marvell,mv88e6085";
reg = <0x2 0>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
status = "disabled";
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch2phy1_topaz: switch2phy1@11 {
reg = <0x11>;
};
switch2phy2_topaz: switch2phy2@12 {
reg = <0x12>;
};
switch2phy3_topaz: switch2phy3@13 {
reg = <0x13>;
};
switch2phy4_topaz: switch2phy4@14 {
reg = <0x14>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1_topaz>;
};
port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2_topaz>;
};
port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3_topaz>;
};
port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4_topaz>;
};
port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
managed = "in-band-status";
link = <&switch1port10 &switch0port10>;
};
};
};
};