| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Copyright (C) 2003-2015 Broadcom Corporation | |
| * All Rights Reserved | |
| */ | |
| #include <linux/gpio/driver.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/module.h> | |
| #include <linux/irq.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irqchip/chained_irq.h> | |
| #include <linux/acpi.h> | |
| /* | |
| * XLP GPIO has multiple 32 bit registers for each feature where each register | |
| * controls 32 pins. So, pins up to 64 require 2 32-bit registers and up to 96 | |
| * require 3 32-bit registers for each feature. | |
| * Here we only define offset of the first register for each feature. Offset of | |
| * the registers for pins greater than 32 can be calculated as following(Use | |
| * GPIO_INT_STAT as example): | |
| * | |
| * offset = (gpio / XLP_GPIO_REGSZ) * 4; | |
| * reg_addr = addr + offset; | |
| * | |
| * where addr is base address of the that feature register and gpio is the pin. | |
| */ | |
| #define GPIO_9XX_BYTESWAP 0X00 | |
| #define GPIO_9XX_CTRL 0X04 | |
| #define GPIO_9XX_OUTPUT_EN 0x14 | |
| #define GPIO_9XX_PADDRV 0x24 | |
| /* | |
| * Only for 4 interrupt enable reg are defined for now, | |
| * total reg available are 12. | |
| */ | |
| #define GPIO_9XX_INT_EN00 0x44 | |
| #define GPIO_9XX_INT_EN10 0x54 | |
| #define GPIO_9XX_INT_EN20 0x64 | |
| #define GPIO_9XX_INT_EN30 0x74 | |
| #define GPIO_9XX_INT_POL 0x104 | |
| #define GPIO_9XX_INT_TYPE 0x114 | |
| #define GPIO_9XX_INT_STAT 0x124 | |
| /* Interrupt type register mask */ | |
| #define XLP_GPIO_IRQ_TYPE_LVL 0x0 | |
| #define XLP_GPIO_IRQ_TYPE_EDGE 0x1 | |
| /* Interrupt polarity register mask */ | |
| #define XLP_GPIO_IRQ_POL_HIGH 0x0 | |
| #define XLP_GPIO_IRQ_POL_LOW 0x1 | |
| #define XLP_GPIO_REGSZ 32 | |
| #define XLP_GPIO_IRQ_BASE 768 | |
| #define XLP_MAX_NR_GPIO 96 | |
| struct xlp_gpio_priv { | |
| struct gpio_chip chip; | |
| DECLARE_BITMAP(gpio_enabled_mask, XLP_MAX_NR_GPIO); | |
| void __iomem *gpio_intr_en; /* pointer to first intr enable reg */ | |
| void __iomem *gpio_intr_stat; /* pointer to first intr status reg */ | |
| void __iomem *gpio_intr_type; /* pointer to first intr type reg */ | |
| void __iomem *gpio_intr_pol; /* pointer to first intr polarity reg */ | |
| void __iomem *gpio_out_en; /* pointer to first output enable reg */ | |
| void __iomem *gpio_paddrv; /* pointer to first pad drive reg */ | |
| spinlock_t lock; | |
| }; | |
| static int xlp_gpio_get_reg(void __iomem *addr, unsigned gpio) | |
| { | |
| u32 pos, regset; | |
| pos = gpio % XLP_GPIO_REGSZ; | |
| regset = (gpio / XLP_GPIO_REGSZ) * 4; | |
| return !!(readl(addr + regset) & BIT(pos)); | |
| } | |
| static void xlp_gpio_set_reg(void __iomem *addr, unsigned gpio, int state) | |
| { | |
| u32 value, pos, regset; | |
| pos = gpio % XLP_GPIO_REGSZ; | |
| regset = (gpio / XLP_GPIO_REGSZ) * 4; | |
| value = readl(addr + regset); | |
| if (state) | |
| value |= BIT(pos); | |
| else | |
| value &= ~BIT(pos); | |
| writel(value, addr + regset); | |
| } | |
| static void xlp_gpio_irq_enable(struct irq_data *d) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| gpiochip_enable_irq(gc, irqd_to_hwirq(d)); | |
| } | |
| static void xlp_gpio_irq_disable(struct irq_data *d) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| unsigned long flags; | |
| spin_lock_irqsave(&priv->lock, flags); | |
| xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x0); | |
| __clear_bit(d->hwirq, priv->gpio_enabled_mask); | |
| spin_unlock_irqrestore(&priv->lock, flags); | |
| gpiochip_disable_irq(gc, irqd_to_hwirq(d)); | |
| } | |
| static void xlp_gpio_irq_mask_ack(struct irq_data *d) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| unsigned long flags; | |
| spin_lock_irqsave(&priv->lock, flags); | |
| xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x0); | |
| xlp_gpio_set_reg(priv->gpio_intr_stat, d->hwirq, 0x1); | |
| __clear_bit(d->hwirq, priv->gpio_enabled_mask); | |
| spin_unlock_irqrestore(&priv->lock, flags); | |
| } | |
| static void xlp_gpio_irq_unmask(struct irq_data *d) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| unsigned long flags; | |
| spin_lock_irqsave(&priv->lock, flags); | |
| xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x1); | |
| __set_bit(d->hwirq, priv->gpio_enabled_mask); | |
| spin_unlock_irqrestore(&priv->lock, flags); | |
| } | |
| static int xlp_gpio_set_irq_type(struct irq_data *d, unsigned int type) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| int pol, irq_type; | |
| switch (type) { | |
| case IRQ_TYPE_EDGE_RISING: | |
| irq_type = XLP_GPIO_IRQ_TYPE_EDGE; | |
| pol = XLP_GPIO_IRQ_POL_HIGH; | |
| break; | |
| case IRQ_TYPE_EDGE_FALLING: | |
| irq_type = XLP_GPIO_IRQ_TYPE_EDGE; | |
| pol = XLP_GPIO_IRQ_POL_LOW; | |
| break; | |
| case IRQ_TYPE_LEVEL_HIGH: | |
| irq_type = XLP_GPIO_IRQ_TYPE_LVL; | |
| pol = XLP_GPIO_IRQ_POL_HIGH; | |
| break; | |
| case IRQ_TYPE_LEVEL_LOW: | |
| irq_type = XLP_GPIO_IRQ_TYPE_LVL; | |
| pol = XLP_GPIO_IRQ_POL_LOW; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| xlp_gpio_set_reg(priv->gpio_intr_type, d->hwirq, irq_type); | |
| xlp_gpio_set_reg(priv->gpio_intr_pol, d->hwirq, pol); | |
| return 0; | |
| } | |
| static struct irq_chip xlp_gpio_irq_chip = { | |
| .name = "XLP-GPIO", | |
| .irq_mask_ack = xlp_gpio_irq_mask_ack, | |
| .irq_enable = xlp_gpio_irq_enable, | |
| .irq_disable = xlp_gpio_irq_disable, | |
| .irq_set_type = xlp_gpio_set_irq_type, | |
| .irq_unmask = xlp_gpio_irq_unmask, | |
| .flags = IRQCHIP_ONESHOT_SAFE | IRQCHIP_IMMUTABLE, | |
| GPIOCHIP_IRQ_RESOURCE_HELPERS, | |
| }; | |
| static void xlp_gpio_generic_handler(struct irq_desc *desc) | |
| { | |
| struct xlp_gpio_priv *priv = irq_desc_get_handler_data(desc); | |
| struct irq_chip *irqchip = irq_desc_get_chip(desc); | |
| int gpio, regoff; | |
| u32 gpio_stat; | |
| regoff = -1; | |
| gpio_stat = 0; | |
| chained_irq_enter(irqchip, desc); | |
| for_each_set_bit(gpio, priv->gpio_enabled_mask, XLP_MAX_NR_GPIO) { | |
| if (regoff != gpio / XLP_GPIO_REGSZ) { | |
| regoff = gpio / XLP_GPIO_REGSZ; | |
| gpio_stat = readl(priv->gpio_intr_stat + regoff * 4); | |
| } | |
| if (gpio_stat & BIT(gpio % XLP_GPIO_REGSZ)) | |
| generic_handle_domain_irq(priv->chip.irq.domain, gpio); | |
| } | |
| chained_irq_exit(irqchip, desc); | |
| } | |
| static int xlp_gpio_dir_output(struct gpio_chip *gc, unsigned gpio, int state) | |
| { | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| xlp_gpio_set_reg(priv->gpio_out_en, gpio, 0x1); | |
| return 0; | |
| } | |
| static int xlp_gpio_dir_input(struct gpio_chip *gc, unsigned gpio) | |
| { | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| xlp_gpio_set_reg(priv->gpio_out_en, gpio, 0x0); | |
| return 0; | |
| } | |
| static int xlp_gpio_get(struct gpio_chip *gc, unsigned gpio) | |
| { | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| return xlp_gpio_get_reg(priv->gpio_paddrv, gpio); | |
| } | |
| static int xlp_gpio_set(struct gpio_chip *gc, unsigned int gpio, int state) | |
| { | |
| struct xlp_gpio_priv *priv = gpiochip_get_data(gc); | |
| xlp_gpio_set_reg(priv->gpio_paddrv, gpio, state); | |
| return 0; | |
| } | |
| static int xlp_gpio_probe(struct platform_device *pdev) | |
| { | |
| struct gpio_chip *gc; | |
| struct gpio_irq_chip *girq; | |
| struct xlp_gpio_priv *priv; | |
| void __iomem *gpio_base; | |
| int irq, err; | |
| priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); | |
| if (!priv) | |
| return -ENOMEM; | |
| gpio_base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(gpio_base)) | |
| return PTR_ERR(gpio_base); | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq < 0) | |
| return irq; | |
| priv->gpio_out_en = gpio_base + GPIO_9XX_OUTPUT_EN; | |
| priv->gpio_paddrv = gpio_base + GPIO_9XX_PADDRV; | |
| priv->gpio_intr_stat = gpio_base + GPIO_9XX_INT_STAT; | |
| priv->gpio_intr_type = gpio_base + GPIO_9XX_INT_TYPE; | |
| priv->gpio_intr_pol = gpio_base + GPIO_9XX_INT_POL; | |
| priv->gpio_intr_en = gpio_base + GPIO_9XX_INT_EN00; | |
| bitmap_zero(priv->gpio_enabled_mask, XLP_MAX_NR_GPIO); | |
| gc = &priv->chip; | |
| gc->owner = THIS_MODULE; | |
| gc->label = dev_name(&pdev->dev); | |
| gc->base = 0; | |
| gc->parent = &pdev->dev; | |
| gc->ngpio = 70; | |
| gc->direction_output = xlp_gpio_dir_output; | |
| gc->direction_input = xlp_gpio_dir_input; | |
| gc->set = xlp_gpio_set; | |
| gc->get = xlp_gpio_get; | |
| spin_lock_init(&priv->lock); | |
| girq = &gc->irq; | |
| gpio_irq_chip_set_chip(girq, &xlp_gpio_irq_chip); | |
| girq->parent_handler = xlp_gpio_generic_handler; | |
| girq->num_parents = 1; | |
| girq->parents = devm_kcalloc(&pdev->dev, 1, | |
| sizeof(*girq->parents), | |
| GFP_KERNEL); | |
| if (!girq->parents) | |
| return -ENOMEM; | |
| girq->parents[0] = irq; | |
| girq->first = 0; | |
| girq->default_type = IRQ_TYPE_NONE; | |
| girq->handler = handle_level_irq; | |
| err = gpiochip_add_data(gc, priv); | |
| if (err < 0) | |
| return err; | |
| dev_info(&pdev->dev, "registered %d GPIOs\n", gc->ngpio); | |
| return 0; | |
| } | |
| #ifdef CONFIG_ACPI | |
| static const struct acpi_device_id xlp_gpio_acpi_match[] = { | |
| { "BRCM9006" }, | |
| { "CAV9006" }, | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(acpi, xlp_gpio_acpi_match); | |
| #endif | |
| static struct platform_driver xlp_gpio_driver = { | |
| .driver = { | |
| .name = "xlp-gpio", | |
| .acpi_match_table = ACPI_PTR(xlp_gpio_acpi_match), | |
| }, | |
| .probe = xlp_gpio_probe, | |
| }; | |
| module_platform_driver(xlp_gpio_driver); | |
| MODULE_AUTHOR("Kamlakant Patel <kamlakant.patel@broadcom.com>"); | |
| MODULE_AUTHOR("Ganesan Ramalingam <ganesanr@broadcom.com>"); | |
| MODULE_DESCRIPTION("Netlogic XLP GPIO Driver"); | |
| MODULE_LICENSE("GPL v2"); |