| // SPDX-License-Identifier: GPL-2.0-or-later | |
| /* | |
| * Copyright (C) 2011 Alexander Stein <alexander.stein@systec-electronic.com> | |
| * | |
| * The LM95245 is a sensor chip made by TI / National Semiconductor. | |
| * It reports up to two temperatures (its own plus an external one). | |
| * | |
| * This driver is based on lm95241.c | |
| */ | |
| #include <linux/err.h> | |
| #include <linux/init.h> | |
| #include <linux/hwmon.h> | |
| #include <linux/i2c.h> | |
| #include <linux/module.h> | |
| #include <linux/regmap.h> | |
| #include <linux/slab.h> | |
| static const unsigned short normal_i2c[] = { | |
| 0x18, 0x19, 0x29, 0x4c, 0x4d, I2C_CLIENT_END }; | |
| /* LM95245 registers */ | |
| /* general registers */ | |
| #define LM95245_REG_RW_CONFIG1 0x03 | |
| #define LM95245_REG_RW_CONVERS_RATE 0x04 | |
| #define LM95245_REG_W_ONE_SHOT 0x0F | |
| /* diode configuration */ | |
| #define LM95245_REG_RW_CONFIG2 0xBF | |
| #define LM95245_REG_RW_REMOTE_OFFH 0x11 | |
| #define LM95245_REG_RW_REMOTE_OFFL 0x12 | |
| /* status registers */ | |
| #define LM95245_REG_R_STATUS1 0x02 | |
| #define LM95245_REG_R_STATUS2 0x33 | |
| /* limit registers */ | |
| #define LM95245_REG_RW_REMOTE_OS_LIMIT 0x07 | |
| #define LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT 0x20 | |
| #define LM95245_REG_RW_REMOTE_TCRIT_LIMIT 0x19 | |
| #define LM95245_REG_RW_COMMON_HYSTERESIS 0x21 | |
| /* temperature signed */ | |
| #define LM95245_REG_R_LOCAL_TEMPH_S 0x00 | |
| #define LM95245_REG_R_LOCAL_TEMPL_S 0x30 | |
| #define LM95245_REG_R_REMOTE_TEMPH_S 0x01 | |
| #define LM95245_REG_R_REMOTE_TEMPL_S 0x10 | |
| /* temperature unsigned */ | |
| #define LM95245_REG_R_REMOTE_TEMPH_U 0x31 | |
| #define LM95245_REG_R_REMOTE_TEMPL_U 0x32 | |
| /* id registers */ | |
| #define LM95245_REG_R_MAN_ID 0xFE | |
| #define LM95245_REG_R_CHIP_ID 0xFF | |
| /* LM95245 specific bitfields */ | |
| #define CFG_STOP 0x40 | |
| #define CFG_REMOTE_TCRIT_MASK 0x10 | |
| #define CFG_REMOTE_OS_MASK 0x08 | |
| #define CFG_LOCAL_TCRIT_MASK 0x04 | |
| #define CFG_LOCAL_OS_MASK 0x02 | |
| #define CFG2_OS_A0 0x40 | |
| #define CFG2_DIODE_FAULT_OS 0x20 | |
| #define CFG2_DIODE_FAULT_TCRIT 0x10 | |
| #define CFG2_REMOTE_TT 0x08 | |
| #define CFG2_REMOTE_FILTER_DIS 0x00 | |
| #define CFG2_REMOTE_FILTER_EN 0x06 | |
| /* conversation rate in ms */ | |
| #define RATE_CR0063 0x00 | |
| #define RATE_CR0364 0x01 | |
| #define RATE_CR1000 0x02 | |
| #define RATE_CR2500 0x03 | |
| #define STATUS1_ROS 0x10 | |
| #define STATUS1_DIODE_FAULT 0x04 | |
| #define STATUS1_RTCRIT 0x02 | |
| #define STATUS1_LOC 0x01 | |
| #define MANUFACTURER_ID 0x01 | |
| #define LM95235_REVISION 0xB1 | |
| #define LM95245_REVISION 0xB3 | |
| /* Client data (each client gets its own) */ | |
| struct lm95245_data { | |
| struct regmap *regmap; | |
| int interval; /* in msecs */ | |
| }; | |
| /* Conversions */ | |
| static int temp_from_reg_unsigned(u8 val_h, u8 val_l) | |
| { | |
| return val_h * 1000 + val_l * 1000 / 256; | |
| } | |
| static int temp_from_reg_signed(u8 val_h, u8 val_l) | |
| { | |
| if (val_h & 0x80) | |
| return (val_h - 0x100) * 1000; | |
| return temp_from_reg_unsigned(val_h, val_l); | |
| } | |
| static int lm95245_read_conversion_rate(struct lm95245_data *data) | |
| { | |
| unsigned int rate; | |
| int ret; | |
| ret = regmap_read(data->regmap, LM95245_REG_RW_CONVERS_RATE, &rate); | |
| if (ret < 0) | |
| return ret; | |
| switch (rate) { | |
| case RATE_CR0063: | |
| data->interval = 63; | |
| break; | |
| case RATE_CR0364: | |
| data->interval = 364; | |
| break; | |
| case RATE_CR1000: | |
| data->interval = 1000; | |
| break; | |
| case RATE_CR2500: | |
| default: | |
| data->interval = 2500; | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int lm95245_set_conversion_rate(struct lm95245_data *data, long interval) | |
| { | |
| int ret, rate; | |
| if (interval <= 63) { | |
| interval = 63; | |
| rate = RATE_CR0063; | |
| } else if (interval <= 364) { | |
| interval = 364; | |
| rate = RATE_CR0364; | |
| } else if (interval <= 1000) { | |
| interval = 1000; | |
| rate = RATE_CR1000; | |
| } else { | |
| interval = 2500; | |
| rate = RATE_CR2500; | |
| } | |
| ret = regmap_write(data->regmap, LM95245_REG_RW_CONVERS_RATE, rate); | |
| if (ret < 0) | |
| return ret; | |
| data->interval = interval; | |
| return 0; | |
| } | |
| static int lm95245_read_temp(struct device *dev, u32 attr, int channel, | |
| long *val) | |
| { | |
| struct lm95245_data *data = dev_get_drvdata(dev); | |
| struct regmap *regmap = data->regmap; | |
| unsigned int regs[2]; | |
| unsigned int regval; | |
| u8 regvals[2]; | |
| int ret; | |
| switch (attr) { | |
| case hwmon_temp_input: | |
| regs[0] = channel ? LM95245_REG_R_REMOTE_TEMPL_S : | |
| LM95245_REG_R_LOCAL_TEMPL_S; | |
| regs[1] = channel ? LM95245_REG_R_REMOTE_TEMPH_S : | |
| LM95245_REG_R_LOCAL_TEMPH_S; | |
| ret = regmap_multi_reg_read(regmap, regs, regvals, 2); | |
| if (ret < 0) | |
| return ret; | |
| /* | |
| * Local temp is always signed. | |
| * Remote temp has both signed and unsigned data. | |
| * Use signed calculation for remote if signed bit is set | |
| * or if reported temperature is below signed limit. | |
| */ | |
| if (!channel || (regvals[1] & 0x80) || regvals[1] < 0x7f) { | |
| *val = temp_from_reg_signed(regvals[1], regvals[0]); | |
| return 0; | |
| } | |
| ret = regmap_bulk_read(regmap, LM95245_REG_R_REMOTE_TEMPH_U, regvals, 2); | |
| if (ret) | |
| return ret; | |
| *val = temp_from_reg_unsigned(regvals[0], regvals[1]); | |
| return 0; | |
| case hwmon_temp_max: | |
| ret = regmap_read(regmap, LM95245_REG_RW_REMOTE_OS_LIMIT, | |
| ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = regval * 1000; | |
| return 0; | |
| case hwmon_temp_crit: | |
| regs[0] = channel ? LM95245_REG_RW_REMOTE_TCRIT_LIMIT : | |
| LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT; | |
| ret = regmap_read(regmap, regs[0], ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = regval * 1000; | |
| return 0; | |
| case hwmon_temp_max_hyst: | |
| regs[0] = LM95245_REG_RW_REMOTE_OS_LIMIT; | |
| regs[1] = LM95245_REG_RW_COMMON_HYSTERESIS; | |
| ret = regmap_multi_reg_read(regmap, regs, regvals, 2); | |
| if (ret < 0) | |
| return ret; | |
| *val = (regvals[0] - regvals[1]) * 1000; | |
| return 0; | |
| case hwmon_temp_crit_hyst: | |
| regs[0] = channel ? LM95245_REG_RW_REMOTE_TCRIT_LIMIT : | |
| LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT; | |
| regs[1] = LM95245_REG_RW_COMMON_HYSTERESIS; | |
| ret = regmap_multi_reg_read(regmap, regs, regvals, 2); | |
| if (ret < 0) | |
| return ret; | |
| *val = (regvals[0] - regvals[1]) * 1000; | |
| return 0; | |
| case hwmon_temp_type: | |
| ret = regmap_read(regmap, LM95245_REG_RW_CONFIG2, ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = (regval & CFG2_REMOTE_TT) ? 1 : 2; | |
| return 0; | |
| case hwmon_temp_offset: | |
| ret = regmap_bulk_read(regmap, LM95245_REG_RW_REMOTE_OFFH, regvals, 2); | |
| if (ret < 0) | |
| return ret; | |
| *val = temp_from_reg_signed(regvals[0], regvals[1]); | |
| return 0; | |
| case hwmon_temp_max_alarm: | |
| ret = regmap_read(regmap, LM95245_REG_R_STATUS1, ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = !!(regval & STATUS1_ROS); | |
| return 0; | |
| case hwmon_temp_crit_alarm: | |
| ret = regmap_read(regmap, LM95245_REG_R_STATUS1, ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = !!(regval & (channel ? STATUS1_RTCRIT : STATUS1_LOC)); | |
| return 0; | |
| case hwmon_temp_fault: | |
| ret = regmap_read(regmap, LM95245_REG_R_STATUS1, ®val); | |
| if (ret < 0) | |
| return ret; | |
| *val = !!(regval & STATUS1_DIODE_FAULT); | |
| return 0; | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static int lm95245_write_temp(struct device *dev, u32 attr, int channel, | |
| long val) | |
| { | |
| struct lm95245_data *data = dev_get_drvdata(dev); | |
| struct regmap *regmap = data->regmap; | |
| unsigned int regval; | |
| u8 regvals[2]; | |
| int ret, reg; | |
| switch (attr) { | |
| case hwmon_temp_max: | |
| val = clamp_val(val / 1000, 0, 255); | |
| ret = regmap_write(regmap, LM95245_REG_RW_REMOTE_OS_LIMIT, val); | |
| return ret; | |
| case hwmon_temp_crit: | |
| reg = channel ? LM95245_REG_RW_REMOTE_TCRIT_LIMIT : | |
| LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT; | |
| val = clamp_val(val / 1000, 0, channel ? 255 : 127); | |
| ret = regmap_write(regmap, reg, val); | |
| return ret; | |
| case hwmon_temp_crit_hyst: | |
| ret = regmap_read(regmap, LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT, | |
| ®val); | |
| if (ret < 0) | |
| return ret; | |
| /* Clamp to reasonable range to prevent overflow */ | |
| val = clamp_val(val, -1000000, 1000000); | |
| val = regval - val / 1000; | |
| val = clamp_val(val, 0, 31); | |
| ret = regmap_write(regmap, LM95245_REG_RW_COMMON_HYSTERESIS, | |
| val); | |
| return ret; | |
| case hwmon_temp_offset: | |
| val = clamp_val(val, -128000, 127875); | |
| val = val * 256 / 1000; | |
| regvals[0] = val >> 8; | |
| regvals[1] = val & 0xe0; | |
| ret = regmap_bulk_write(regmap, LM95245_REG_RW_REMOTE_OFFH, regvals, 2); | |
| return ret; | |
| case hwmon_temp_type: | |
| if (val != 1 && val != 2) | |
| return -EINVAL; | |
| ret = regmap_update_bits(regmap, LM95245_REG_RW_CONFIG2, | |
| CFG2_REMOTE_TT, | |
| val == 1 ? CFG2_REMOTE_TT : 0); | |
| return ret; | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static int lm95245_read_chip(struct device *dev, u32 attr, int channel, | |
| long *val) | |
| { | |
| struct lm95245_data *data = dev_get_drvdata(dev); | |
| switch (attr) { | |
| case hwmon_chip_update_interval: | |
| *val = data->interval; | |
| return 0; | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static int lm95245_write_chip(struct device *dev, u32 attr, int channel, | |
| long val) | |
| { | |
| struct lm95245_data *data = dev_get_drvdata(dev); | |
| switch (attr) { | |
| case hwmon_chip_update_interval: | |
| return lm95245_set_conversion_rate(data, val); | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static int lm95245_read(struct device *dev, enum hwmon_sensor_types type, | |
| u32 attr, int channel, long *val) | |
| { | |
| switch (type) { | |
| case hwmon_chip: | |
| return lm95245_read_chip(dev, attr, channel, val); | |
| case hwmon_temp: | |
| return lm95245_read_temp(dev, attr, channel, val); | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static int lm95245_write(struct device *dev, enum hwmon_sensor_types type, | |
| u32 attr, int channel, long val) | |
| { | |
| switch (type) { | |
| case hwmon_chip: | |
| return lm95245_write_chip(dev, attr, channel, val); | |
| case hwmon_temp: | |
| return lm95245_write_temp(dev, attr, channel, val); | |
| default: | |
| return -EOPNOTSUPP; | |
| } | |
| } | |
| static umode_t lm95245_temp_is_visible(const void *data, u32 attr, int channel) | |
| { | |
| switch (attr) { | |
| case hwmon_temp_input: | |
| case hwmon_temp_max_alarm: | |
| case hwmon_temp_max_hyst: | |
| case hwmon_temp_crit_alarm: | |
| case hwmon_temp_fault: | |
| return 0444; | |
| case hwmon_temp_type: | |
| case hwmon_temp_max: | |
| case hwmon_temp_crit: | |
| case hwmon_temp_offset: | |
| return 0644; | |
| case hwmon_temp_crit_hyst: | |
| return (channel == 0) ? 0644 : 0444; | |
| default: | |
| return 0; | |
| } | |
| } | |
| static umode_t lm95245_is_visible(const void *data, | |
| enum hwmon_sensor_types type, | |
| u32 attr, int channel) | |
| { | |
| switch (type) { | |
| case hwmon_chip: | |
| switch (attr) { | |
| case hwmon_chip_update_interval: | |
| return 0644; | |
| default: | |
| return 0; | |
| } | |
| case hwmon_temp: | |
| return lm95245_temp_is_visible(data, attr, channel); | |
| default: | |
| return 0; | |
| } | |
| } | |
| /* Return 0 if detection is successful, -ENODEV otherwise */ | |
| static int lm95245_detect(struct i2c_client *new_client, | |
| struct i2c_board_info *info) | |
| { | |
| struct i2c_adapter *adapter = new_client->adapter; | |
| int address = new_client->addr; | |
| const char *name; | |
| int rev, id; | |
| if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) | |
| return -ENODEV; | |
| id = i2c_smbus_read_byte_data(new_client, LM95245_REG_R_MAN_ID); | |
| if (id != MANUFACTURER_ID) | |
| return -ENODEV; | |
| rev = i2c_smbus_read_byte_data(new_client, LM95245_REG_R_CHIP_ID); | |
| switch (rev) { | |
| case LM95235_REVISION: | |
| if (address != 0x18 && address != 0x29 && address != 0x4c) | |
| return -ENODEV; | |
| name = "lm95235"; | |
| break; | |
| case LM95245_REVISION: | |
| name = "lm95245"; | |
| break; | |
| default: | |
| return -ENODEV; | |
| } | |
| strscpy(info->type, name, I2C_NAME_SIZE); | |
| return 0; | |
| } | |
| static int lm95245_init_client(struct lm95245_data *data) | |
| { | |
| int ret; | |
| ret = lm95245_read_conversion_rate(data); | |
| if (ret < 0) | |
| return ret; | |
| return regmap_update_bits(data->regmap, LM95245_REG_RW_CONFIG1, | |
| CFG_STOP, 0); | |
| } | |
| static bool lm95245_is_writeable_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case LM95245_REG_RW_CONFIG1: | |
| case LM95245_REG_RW_CONVERS_RATE: | |
| case LM95245_REG_W_ONE_SHOT: | |
| case LM95245_REG_RW_CONFIG2: | |
| case LM95245_REG_RW_REMOTE_OFFH: | |
| case LM95245_REG_RW_REMOTE_OFFL: | |
| case LM95245_REG_RW_REMOTE_OS_LIMIT: | |
| case LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT: | |
| case LM95245_REG_RW_REMOTE_TCRIT_LIMIT: | |
| case LM95245_REG_RW_COMMON_HYSTERESIS: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static bool lm95245_is_volatile_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case LM95245_REG_R_STATUS1: | |
| case LM95245_REG_R_STATUS2: | |
| case LM95245_REG_R_LOCAL_TEMPH_S: | |
| case LM95245_REG_R_LOCAL_TEMPL_S: | |
| case LM95245_REG_R_REMOTE_TEMPH_S: | |
| case LM95245_REG_R_REMOTE_TEMPL_S: | |
| case LM95245_REG_R_REMOTE_TEMPH_U: | |
| case LM95245_REG_R_REMOTE_TEMPL_U: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static const struct regmap_config lm95245_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .writeable_reg = lm95245_is_writeable_reg, | |
| .volatile_reg = lm95245_is_volatile_reg, | |
| .cache_type = REGCACHE_MAPLE, | |
| .use_single_read = true, | |
| .use_single_write = true, | |
| }; | |
| static const struct hwmon_channel_info * const lm95245_info[] = { | |
| HWMON_CHANNEL_INFO(chip, | |
| HWMON_C_UPDATE_INTERVAL), | |
| HWMON_CHANNEL_INFO(temp, | |
| HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_HYST | | |
| HWMON_T_CRIT_ALARM, | |
| HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MAX_HYST | | |
| HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_FAULT | | |
| HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM | | |
| HWMON_T_TYPE | HWMON_T_OFFSET), | |
| NULL | |
| }; | |
| static const struct hwmon_ops lm95245_hwmon_ops = { | |
| .is_visible = lm95245_is_visible, | |
| .read = lm95245_read, | |
| .write = lm95245_write, | |
| }; | |
| static const struct hwmon_chip_info lm95245_chip_info = { | |
| .ops = &lm95245_hwmon_ops, | |
| .info = lm95245_info, | |
| }; | |
| static int lm95245_probe(struct i2c_client *client) | |
| { | |
| struct device *dev = &client->dev; | |
| struct lm95245_data *data; | |
| struct device *hwmon_dev; | |
| int ret; | |
| data = devm_kzalloc(dev, sizeof(struct lm95245_data), GFP_KERNEL); | |
| if (!data) | |
| return -ENOMEM; | |
| data->regmap = devm_regmap_init_i2c(client, &lm95245_regmap_config); | |
| if (IS_ERR(data->regmap)) | |
| return PTR_ERR(data->regmap); | |
| /* Initialize the LM95245 chip */ | |
| ret = lm95245_init_client(data); | |
| if (ret < 0) | |
| return ret; | |
| hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, | |
| data, | |
| &lm95245_chip_info, | |
| NULL); | |
| return PTR_ERR_OR_ZERO(hwmon_dev); | |
| } | |
| /* Driver data (common to all clients) */ | |
| static const struct i2c_device_id lm95245_id[] = { | |
| { .name = "lm95235" }, | |
| { .name = "lm95245" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, lm95245_id); | |
| static const struct of_device_id __maybe_unused lm95245_of_match[] = { | |
| { .compatible = "national,lm95235" }, | |
| { .compatible = "national,lm95245" }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, lm95245_of_match); | |
| static struct i2c_driver lm95245_driver = { | |
| .class = I2C_CLASS_HWMON, | |
| .driver = { | |
| .name = "lm95245", | |
| .of_match_table = of_match_ptr(lm95245_of_match), | |
| }, | |
| .probe = lm95245_probe, | |
| .id_table = lm95245_id, | |
| .detect = lm95245_detect, | |
| .address_list = normal_i2c, | |
| }; | |
| module_i2c_driver(lm95245_driver); | |
| MODULE_AUTHOR("Alexander Stein <alexander.stein@systec-electronic.com>"); | |
| MODULE_DESCRIPTION("LM95235/LM95245 sensor driver"); | |
| MODULE_LICENSE("GPL"); |