| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Driver for Future Domain TMC-16x0 and TMC-3260 SCSI host adapters | |
| * Copyright 2019 Ondrej Zary | |
| * | |
| * Original driver by | |
| * Rickard E. Faith, faith@cs.unc.edu | |
| * | |
| * Future Domain BIOS versions supported for autodetect: | |
| * 2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61 | |
| * Chips supported: | |
| * TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70 | |
| * Boards supported: | |
| * Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX | |
| * Future Domain TMC-3260 (PCI) | |
| * Quantum ISA-200S, ISA-250MG | |
| * Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead] | |
| * IBM ? | |
| * | |
| * NOTE: | |
| * | |
| * The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it. | |
| * Use the aic7xxx driver for this board. | |
| * | |
| * The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right | |
| * driver for that card. Unfortunately, the boxes will probably just say | |
| * "2920", so you'll have to look on the card for a Future Domain logo, or a | |
| * letter after the 2920. | |
| * | |
| * If you have a TMC-8xx or TMC-9xx board, then this is not the driver for | |
| * your board. | |
| * | |
| * DESCRIPTION: | |
| * | |
| * This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680 | |
| * TMC-1650/1670, and TMC-3260 SCSI host adapters. The 1650 and 1670 have a | |
| * 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin | |
| * high-density external connector. The 1670 and 1680 have floppy disk | |
| * controllers built in. The TMC-3260 is a PCI bus card. | |
| * | |
| * Future Domain's older boards are based on the TMC-1800 chip, and this | |
| * driver was originally written for a TMC-1680 board with the TMC-1800 chip. | |
| * More recently, boards are being produced with the TMC-18C50 and TMC-18C30 | |
| * chips. | |
| * | |
| * Please note that the drive ordering that Future Domain implemented in BIOS | |
| * versions 3.4 and 3.5 is the opposite of the order (currently) used by the | |
| * rest of the SCSI industry. | |
| * | |
| * | |
| * REFERENCES USED: | |
| * | |
| * "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation, | |
| * 1990. | |
| * | |
| * "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain | |
| * Corporation, January 1992. | |
| * | |
| * "LXT SCSI Products: Specifications and OEM Technical Manual (Revision | |
| * B/September 1991)", Maxtor Corporation, 1991. | |
| * | |
| * "7213S product Manual (Revision P3)", Maxtor Corporation, 1992. | |
| * | |
| * "Draft Proposed American National Standard: Small Computer System | |
| * Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109, | |
| * revision 10h, October 17, 1991) | |
| * | |
| * Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric | |
| * Youngdale (ericy@cais.com), 1992. | |
| * | |
| * Private communication, Tuong Le (Future Domain Engineering department), | |
| * 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and | |
| * TMC-18C30 detection.) | |
| * | |
| * Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page | |
| * 60 (2.39: Disk Partition Table Layout). | |
| * | |
| * "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page | |
| * 6-1. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/delay.h> | |
| #include <linux/pci.h> | |
| #include <linux/workqueue.h> | |
| #include <scsi/scsicam.h> | |
| #include <scsi/scsi_cmnd.h> | |
| #include <scsi/scsi_device.h> | |
| #include <scsi/scsi_host.h> | |
| #include "fdomain.h" | |
| /* | |
| * FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the | |
| * 18C30 chip have a 2k cache). When this many 512 byte blocks are filled by | |
| * the SCSI device, an interrupt will be raised. Therefore, this could be as | |
| * low as 0, or as high as 16. Note, however, that values which are too high | |
| * or too low seem to prevent any interrupts from occurring, and thereby lock | |
| * up the machine. | |
| */ | |
| #define FIFO_COUNT 2 /* Number of 512 byte blocks before INTR */ | |
| #define PARITY_MASK ACTL_PAREN /* Parity enabled, 0 = disabled */ | |
| enum chip_type { | |
| unknown = 0x00, | |
| tmc1800 = 0x01, | |
| tmc18c50 = 0x02, | |
| tmc18c30 = 0x03, | |
| }; | |
| struct fdomain { | |
| int base; | |
| struct scsi_cmnd *cur_cmd; | |
| enum chip_type chip; | |
| struct work_struct work; | |
| }; | |
| static struct scsi_pointer *fdomain_scsi_pointer(struct scsi_cmnd *cmd) | |
| { | |
| return scsi_cmd_priv(cmd); | |
| } | |
| static inline void fdomain_make_bus_idle(struct fdomain *fd) | |
| { | |
| outb(0, fd->base + REG_BCTL); | |
| outb(0, fd->base + REG_MCTL); | |
| if (fd->chip == tmc18c50 || fd->chip == tmc18c30) | |
| /* Clear forced intr. */ | |
| outb(ACTL_RESET | ACTL_CLRFIRQ | PARITY_MASK, | |
| fd->base + REG_ACTL); | |
| else | |
| outb(ACTL_RESET | PARITY_MASK, fd->base + REG_ACTL); | |
| } | |
| static enum chip_type fdomain_identify(int port) | |
| { | |
| u16 id = inb(port + REG_ID_LSB) | inb(port + REG_ID_MSB) << 8; | |
| switch (id) { | |
| case 0x6127: | |
| return tmc1800; | |
| case 0x60e9: /* 18c50 or 18c30 */ | |
| break; | |
| default: | |
| return unknown; | |
| } | |
| /* Try to toggle 32-bit mode. This only works on an 18c30 chip. */ | |
| outb(CFG2_32BIT, port + REG_CFG2); | |
| if ((inb(port + REG_CFG2) & CFG2_32BIT)) { | |
| outb(0, port + REG_CFG2); | |
| if ((inb(port + REG_CFG2) & CFG2_32BIT) == 0) | |
| return tmc18c30; | |
| } | |
| /* If that failed, we are an 18c50. */ | |
| return tmc18c50; | |
| } | |
| static int fdomain_test_loopback(int base) | |
| { | |
| int i; | |
| for (i = 0; i < 255; i++) { | |
| outb(i, base + REG_LOOPBACK); | |
| if (inb(base + REG_LOOPBACK) != i) | |
| return 1; | |
| } | |
| return 0; | |
| } | |
| static void fdomain_reset(int base) | |
| { | |
| outb(BCTL_RST, base + REG_BCTL); | |
| mdelay(20); | |
| outb(0, base + REG_BCTL); | |
| mdelay(1150); | |
| outb(0, base + REG_MCTL); | |
| outb(PARITY_MASK, base + REG_ACTL); | |
| } | |
| static int fdomain_select(struct Scsi_Host *sh, int target) | |
| { | |
| int status; | |
| unsigned long timeout; | |
| struct fdomain *fd = shost_priv(sh); | |
| outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL); | |
| outb(BIT(sh->this_id) | BIT(target), fd->base + REG_SCSI_DATA_NOACK); | |
| /* Stop arbitration and enable parity */ | |
| outb(PARITY_MASK, fd->base + REG_ACTL); | |
| timeout = 350; /* 350 msec */ | |
| do { | |
| status = inb(fd->base + REG_BSTAT); | |
| if (status & BSTAT_BSY) { | |
| /* Enable SCSI Bus */ | |
| /* (on error, should make bus idle with 0) */ | |
| outb(BCTL_BUSEN, fd->base + REG_BCTL); | |
| return 0; | |
| } | |
| mdelay(1); | |
| } while (--timeout); | |
| fdomain_make_bus_idle(fd); | |
| return 1; | |
| } | |
| static void fdomain_finish_cmd(struct fdomain *fd) | |
| { | |
| outb(0, fd->base + REG_ICTL); | |
| fdomain_make_bus_idle(fd); | |
| scsi_done(fd->cur_cmd); | |
| fd->cur_cmd = NULL; | |
| } | |
| static void fdomain_read_data(struct scsi_cmnd *cmd) | |
| { | |
| struct fdomain *fd = shost_priv(cmd->device->host); | |
| unsigned char *virt, *ptr; | |
| size_t offset, len; | |
| while ((len = inw(fd->base + REG_FIFO_COUNT)) > 0) { | |
| offset = scsi_bufflen(cmd) - scsi_get_resid(cmd); | |
| virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd), | |
| &offset, &len); | |
| ptr = virt + offset; | |
| if (len & 1) | |
| *ptr++ = inb(fd->base + REG_FIFO); | |
| if (len > 1) | |
| insw(fd->base + REG_FIFO, ptr, len >> 1); | |
| scsi_set_resid(cmd, scsi_get_resid(cmd) - len); | |
| scsi_kunmap_atomic_sg(virt); | |
| } | |
| } | |
| static void fdomain_write_data(struct scsi_cmnd *cmd) | |
| { | |
| struct fdomain *fd = shost_priv(cmd->device->host); | |
| /* 8k FIFO for pre-tmc18c30 chips, 2k FIFO for tmc18c30 */ | |
| int FIFO_Size = fd->chip == tmc18c30 ? 0x800 : 0x2000; | |
| unsigned char *virt, *ptr; | |
| size_t offset, len; | |
| while ((len = FIFO_Size - inw(fd->base + REG_FIFO_COUNT)) > 512) { | |
| offset = scsi_bufflen(cmd) - scsi_get_resid(cmd); | |
| if (len + offset > scsi_bufflen(cmd)) { | |
| len = scsi_bufflen(cmd) - offset; | |
| if (len == 0) | |
| break; | |
| } | |
| virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd), | |
| &offset, &len); | |
| ptr = virt + offset; | |
| if (len & 1) | |
| outb(*ptr++, fd->base + REG_FIFO); | |
| if (len > 1) | |
| outsw(fd->base + REG_FIFO, ptr, len >> 1); | |
| scsi_set_resid(cmd, scsi_get_resid(cmd) - len); | |
| scsi_kunmap_atomic_sg(virt); | |
| } | |
| } | |
| static void fdomain_work(struct work_struct *work) | |
| { | |
| struct fdomain *fd = container_of(work, struct fdomain, work); | |
| struct Scsi_Host *sh = container_of((void *)fd, struct Scsi_Host, | |
| hostdata); | |
| struct scsi_cmnd *cmd = fd->cur_cmd; | |
| struct scsi_pointer *scsi_pointer = fdomain_scsi_pointer(cmd); | |
| unsigned long flags; | |
| int status; | |
| int done = 0; | |
| spin_lock_irqsave(sh->host_lock, flags); | |
| if (scsi_pointer->phase & in_arbitration) { | |
| status = inb(fd->base + REG_ASTAT); | |
| if (!(status & ASTAT_ARB)) { | |
| set_host_byte(cmd, DID_BUS_BUSY); | |
| fdomain_finish_cmd(fd); | |
| goto out; | |
| } | |
| scsi_pointer->phase = in_selection; | |
| outb(ICTL_SEL | FIFO_COUNT, fd->base + REG_ICTL); | |
| outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL); | |
| outb(BIT(cmd->device->host->this_id) | BIT(scmd_id(cmd)), | |
| fd->base + REG_SCSI_DATA_NOACK); | |
| /* Stop arbitration and enable parity */ | |
| outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | |
| goto out; | |
| } else if (scsi_pointer->phase & in_selection) { | |
| status = inb(fd->base + REG_BSTAT); | |
| if (!(status & BSTAT_BSY)) { | |
| /* Try again, for slow devices */ | |
| if (fdomain_select(cmd->device->host, scmd_id(cmd))) { | |
| set_host_byte(cmd, DID_NO_CONNECT); | |
| fdomain_finish_cmd(fd); | |
| goto out; | |
| } | |
| /* Stop arbitration and enable parity */ | |
| outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | |
| } | |
| scsi_pointer->phase = in_other; | |
| outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, fd->base + REG_ICTL); | |
| outb(BCTL_BUSEN, fd->base + REG_BCTL); | |
| goto out; | |
| } | |
| /* fdomain_scsi_pointer(cur_cmd)->phase == in_other: this is the body of the routine */ | |
| status = inb(fd->base + REG_BSTAT); | |
| if (status & BSTAT_REQ) { | |
| switch (status & (BSTAT_MSG | BSTAT_CMD | BSTAT_IO)) { | |
| case BSTAT_CMD: /* COMMAND OUT */ | |
| outb(cmd->cmnd[scsi_pointer->sent_command++], | |
| fd->base + REG_SCSI_DATA); | |
| break; | |
| case 0: /* DATA OUT -- tmc18c50/tmc18c30 only */ | |
| if (fd->chip != tmc1800 && !scsi_pointer->have_data_in) { | |
| scsi_pointer->have_data_in = -1; | |
| outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN | | |
| PARITY_MASK, fd->base + REG_ACTL); | |
| } | |
| break; | |
| case BSTAT_IO: /* DATA IN -- tmc18c50/tmc18c30 only */ | |
| if (fd->chip != tmc1800 && !scsi_pointer->have_data_in) { | |
| scsi_pointer->have_data_in = 1; | |
| outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK, | |
| fd->base + REG_ACTL); | |
| } | |
| break; | |
| case BSTAT_CMD | BSTAT_IO: /* STATUS IN */ | |
| scsi_pointer->Status = inb(fd->base + REG_SCSI_DATA); | |
| break; | |
| case BSTAT_MSG | BSTAT_CMD: /* MESSAGE OUT */ | |
| outb(MESSAGE_REJECT, fd->base + REG_SCSI_DATA); | |
| break; | |
| case BSTAT_MSG | BSTAT_CMD | BSTAT_IO: /* MESSAGE IN */ | |
| scsi_pointer->Message = inb(fd->base + REG_SCSI_DATA); | |
| if (scsi_pointer->Message == COMMAND_COMPLETE) | |
| ++done; | |
| break; | |
| } | |
| } | |
| if (fd->chip == tmc1800 && !scsi_pointer->have_data_in && | |
| scsi_pointer->sent_command >= cmd->cmd_len) { | |
| if (cmd->sc_data_direction == DMA_TO_DEVICE) { | |
| scsi_pointer->have_data_in = -1; | |
| outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN | | |
| PARITY_MASK, fd->base + REG_ACTL); | |
| } else { | |
| scsi_pointer->have_data_in = 1; | |
| outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK, | |
| fd->base + REG_ACTL); | |
| } | |
| } | |
| if (scsi_pointer->have_data_in == -1) /* DATA OUT */ | |
| fdomain_write_data(cmd); | |
| if (scsi_pointer->have_data_in == 1) /* DATA IN */ | |
| fdomain_read_data(cmd); | |
| if (done) { | |
| set_status_byte(cmd, scsi_pointer->Status); | |
| set_host_byte(cmd, DID_OK); | |
| scsi_msg_to_host_byte(cmd, scsi_pointer->Message); | |
| fdomain_finish_cmd(fd); | |
| } else { | |
| if (scsi_pointer->phase & disconnect) { | |
| outb(ICTL_FIFO | ICTL_SEL | ICTL_REQ | FIFO_COUNT, | |
| fd->base + REG_ICTL); | |
| outb(0, fd->base + REG_BCTL); | |
| } else | |
| outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, | |
| fd->base + REG_ICTL); | |
| } | |
| out: | |
| spin_unlock_irqrestore(sh->host_lock, flags); | |
| } | |
| static irqreturn_t fdomain_irq(int irq, void *dev_id) | |
| { | |
| struct fdomain *fd = dev_id; | |
| /* Is it our IRQ? */ | |
| if ((inb(fd->base + REG_ASTAT) & ASTAT_IRQ) == 0) | |
| return IRQ_NONE; | |
| outb(0, fd->base + REG_ICTL); | |
| /* We usually have one spurious interrupt after each command. */ | |
| if (!fd->cur_cmd) /* Spurious interrupt */ | |
| return IRQ_NONE; | |
| schedule_work(&fd->work); | |
| return IRQ_HANDLED; | |
| } | |
| static enum scsi_qc_status fdomain_queue(struct Scsi_Host *sh, | |
| struct scsi_cmnd *cmd) | |
| { | |
| struct scsi_pointer *scsi_pointer = fdomain_scsi_pointer(cmd); | |
| struct fdomain *fd = shost_priv(cmd->device->host); | |
| unsigned long flags; | |
| scsi_pointer->Status = 0; | |
| scsi_pointer->Message = 0; | |
| scsi_pointer->have_data_in = 0; | |
| scsi_pointer->sent_command = 0; | |
| scsi_pointer->phase = in_arbitration; | |
| scsi_set_resid(cmd, scsi_bufflen(cmd)); | |
| spin_lock_irqsave(sh->host_lock, flags); | |
| fd->cur_cmd = cmd; | |
| fdomain_make_bus_idle(fd); | |
| /* Start arbitration */ | |
| outb(0, fd->base + REG_ICTL); | |
| outb(0, fd->base + REG_BCTL); /* Disable data drivers */ | |
| /* Set our id bit */ | |
| outb(BIT(cmd->device->host->this_id), fd->base + REG_SCSI_DATA_NOACK); | |
| outb(ICTL_ARB, fd->base + REG_ICTL); | |
| /* Start arbitration */ | |
| outb(ACTL_ARB | ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | |
| spin_unlock_irqrestore(sh->host_lock, flags); | |
| return 0; | |
| } | |
| static int fdomain_abort(struct scsi_cmnd *cmd) | |
| { | |
| struct Scsi_Host *sh = cmd->device->host; | |
| struct fdomain *fd = shost_priv(sh); | |
| unsigned long flags; | |
| if (!fd->cur_cmd) | |
| return FAILED; | |
| spin_lock_irqsave(sh->host_lock, flags); | |
| fdomain_make_bus_idle(fd); | |
| fdomain_scsi_pointer(fd->cur_cmd)->phase |= aborted; | |
| /* Aborts are not done well. . . */ | |
| set_host_byte(fd->cur_cmd, DID_ABORT); | |
| fdomain_finish_cmd(fd); | |
| spin_unlock_irqrestore(sh->host_lock, flags); | |
| return SUCCESS; | |
| } | |
| static int fdomain_host_reset(struct scsi_cmnd *cmd) | |
| { | |
| struct Scsi_Host *sh = cmd->device->host; | |
| struct fdomain *fd = shost_priv(sh); | |
| unsigned long flags; | |
| spin_lock_irqsave(sh->host_lock, flags); | |
| fdomain_reset(fd->base); | |
| spin_unlock_irqrestore(sh->host_lock, flags); | |
| return SUCCESS; | |
| } | |
| static int fdomain_biosparam(struct scsi_device *sdev, | |
| struct gendisk *disk, sector_t capacity, | |
| int geom[]) | |
| { | |
| unsigned char *p = scsi_bios_ptable(disk); | |
| if (p && p[65] == 0xaa && p[64] == 0x55 /* Partition table valid */ | |
| && p[4]) { /* Partition type */ | |
| geom[0] = p[5] + 1; /* heads */ | |
| geom[1] = p[6] & 0x3f; /* sectors */ | |
| } else { | |
| if (capacity >= 0x7e0000) { | |
| geom[0] = 255; /* heads */ | |
| geom[1] = 63; /* sectors */ | |
| } else if (capacity >= 0x200000) { | |
| geom[0] = 128; /* heads */ | |
| geom[1] = 63; /* sectors */ | |
| } else { | |
| geom[0] = 64; /* heads */ | |
| geom[1] = 32; /* sectors */ | |
| } | |
| } | |
| geom[2] = sector_div(capacity, geom[0] * geom[1]); | |
| kfree(p); | |
| return 0; | |
| } | |
| static const struct scsi_host_template fdomain_template = { | |
| .module = THIS_MODULE, | |
| .name = "Future Domain TMC-16x0", | |
| .proc_name = "fdomain", | |
| .queuecommand = fdomain_queue, | |
| .eh_abort_handler = fdomain_abort, | |
| .eh_host_reset_handler = fdomain_host_reset, | |
| .bios_param = fdomain_biosparam, | |
| .can_queue = 1, | |
| .this_id = 7, | |
| .sg_tablesize = 64, | |
| .dma_boundary = PAGE_SIZE - 1, | |
| .cmd_size = sizeof(struct scsi_pointer), | |
| }; | |
| struct Scsi_Host *fdomain_create(int base, int irq, int this_id, | |
| struct device *dev) | |
| { | |
| struct Scsi_Host *sh; | |
| struct fdomain *fd; | |
| enum chip_type chip; | |
| static const char * const chip_names[] = { | |
| "Unknown", "TMC-1800", "TMC-18C50", "TMC-18C30" | |
| }; | |
| unsigned long irq_flags = 0; | |
| chip = fdomain_identify(base); | |
| if (!chip) | |
| return NULL; | |
| fdomain_reset(base); | |
| if (fdomain_test_loopback(base)) | |
| return NULL; | |
| if (!irq) { | |
| dev_err(dev, "card has no IRQ assigned"); | |
| return NULL; | |
| } | |
| sh = scsi_host_alloc(&fdomain_template, sizeof(struct fdomain)); | |
| if (!sh) | |
| return NULL; | |
| if (this_id) | |
| sh->this_id = this_id & 0x07; | |
| sh->irq = irq; | |
| sh->io_port = base; | |
| sh->n_io_port = FDOMAIN_REGION_SIZE; | |
| fd = shost_priv(sh); | |
| fd->base = base; | |
| fd->chip = chip; | |
| INIT_WORK(&fd->work, fdomain_work); | |
| if (dev_is_pci(dev) || !strcmp(dev->bus->name, "pcmcia")) | |
| irq_flags = IRQF_SHARED; | |
| if (request_irq(irq, fdomain_irq, irq_flags, "fdomain", fd)) | |
| goto fail_put; | |
| shost_printk(KERN_INFO, sh, "%s chip at 0x%x irq %d SCSI ID %d\n", | |
| dev_is_pci(dev) ? "TMC-36C70 (PCI bus)" : chip_names[chip], | |
| base, irq, sh->this_id); | |
| if (scsi_add_host(sh, dev)) | |
| goto fail_free_irq; | |
| scsi_scan_host(sh); | |
| return sh; | |
| fail_free_irq: | |
| free_irq(irq, fd); | |
| fail_put: | |
| scsi_host_put(sh); | |
| return NULL; | |
| } | |
| EXPORT_SYMBOL_GPL(fdomain_create); | |
| int fdomain_destroy(struct Scsi_Host *sh) | |
| { | |
| struct fdomain *fd = shost_priv(sh); | |
| cancel_work_sync(&fd->work); | |
| scsi_remove_host(sh); | |
| if (sh->irq) | |
| free_irq(sh->irq, fd); | |
| scsi_host_put(sh); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL_GPL(fdomain_destroy); | |
| #ifdef CONFIG_PM_SLEEP | |
| static int fdomain_resume(struct device *dev) | |
| { | |
| struct fdomain *fd = shost_priv(dev_get_drvdata(dev)); | |
| fdomain_reset(fd->base); | |
| return 0; | |
| } | |
| static SIMPLE_DEV_PM_OPS(fdomain_pm_ops, NULL, fdomain_resume); | |
| #endif /* CONFIG_PM_SLEEP */ | |
| MODULE_AUTHOR("Ondrej Zary, Rickard E. Faith"); | |
| MODULE_DESCRIPTION("Future Domain TMC-16x0/TMC-3260 SCSI driver"); | |
| MODULE_LICENSE("GPL"); |